• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.3
• /
• pp.195-207
• /
• 2017

Recently, the SAR-GMTI mode is becoming increasingly essential in airborne radar systems. While SAR requires wideband waveforms for high resolution imaging, GMTI requires narrowband waveforms for doppler processing, which makes general LFM waveforms difficult to use for SAR-GMTI. This paper analyses the FJB(Frequency Jump Burst) waveform, which is studied for the SAR-GMTI waveform, and presents the method for the pulse compression and SAR image formation using FJB waveforms. Simulation results show that there is little difference in performances between the FJB waveform and the LFM waveform.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.5
• /
• pp.49-54
• /
• 2013

We designed a burst mode optical receiver for 1.25Gbps PON(Passive Optical Network), fabricated it using $0.8{\mu}m$ BiCMOS foundry. We minimized the loss of the data in the front of the burst by reducing AGC(Automatic Gain Control) signal generation time using an exponential amplifier. We confirmed that AGC of the burst mode optical receiver functioned well and showed good performance in measurement. However, although the eye of the eye pattern was opened the jitter characteristic was deteriorated due to the heavy waveform distortion.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.6
• /
• pp.541-549
• /
• 2007

This work describes an investigation into the feasibility of using an acoustic emission (AE) technique to evaluate the integrity of a composite actuator with a PZT ceramic under electromechanical cyclic loading. AE characteristics have been analyzed in terms of the behavior of the AE count rate and signal waveform in association with the performance degradation of the composite actuator during the cyclic tests. The results showed that the fatigue cracking of the composite actuator with a PZT ceramic occurred only in the PZT ceramic layer, and that the performance degradation caused by the fatigue damage varied immensely depending on the existence of a protecting composite bottom layer. We confirmed the correlations between the fatigue damage mechanisms and AE signal types for the actuators that exhibited multiple modes of fatigue damage; transgranular micro damage, intergranular fatigue cracking, and breakdown by a short circuiting were related to a burst type signal showing a shortly rising and slowly decaying waveform with a comparably low voltage, a continuous type signal showing a gradual rising and slowly decaying waveform with a very high voltage and a burst and continuous type signal with a high voltage, respectively. Results from the present work showed that the evolution of fatigue damage in the composite actuator with a PZT ceramic can be nondestructively identified via in situ AE monitoring and microscopic observations.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1983.10a
• /
• pp.102-104
• /
• 1983

This paper analyzes the patterns of Toneburst Waveform that generated Volumetarily in Broadband, as various Parameters, and applicate in the case that it is mixed Random Noise. As a result, it prooves that auto correlation function is Optimal parameter in analysis of Tone Burst wave form but reference signal.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.931-932
• /
• 2010

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.14-17
• /
• 2006

To diagnosis abnormal compressor conditions in an air-conditioner, the acoustic emission (AE) signal, which is derived from wear condition, compressed air, and assembly error, was analyzed experimentally. Burst and continuous type AE signals resulted from metal contact and compressed air, and the raw AE signal of compressors was acquired in the production line. After extracting samples using waveforms, the Early Life Test (ELT) was conducted and the waveform was classified as normal or abnormal. Efficient parameters in the waveform pattern were investigated in time and frequency domains and a diagnosis algorithm for air-conditioners using Neural Network estimation is suggested.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.11
• /
• pp.125-129
• /
• 2004

For the diagnosis of compressor abnormal condition in air-conditioner, AE signal which is derived from wear condition, compressed air and assembly error is analyzed experimentally. The burst and continuous type AE signal occurred by metal contact and compressed air and AE raw signal of compressors were directly acquired in production line. After extracting samples according to waveforms, Early Life Test(ELT) is conducted and classified to normal and abnormal waveform. The efficient parameters of waveform pattern are investigated in time and frequency domain and the diagnosis algorithm of air-conditioner by Neural Network estimation is suggested.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.9
• /
• pp.930-937
• /
• 2014

Inverse synthetic aperture radar (ISAR) images can be generated by radar which radiates the electromagnetic wave to a target and receives signal reflected from the target. ISAR images can be widely used to target detection and recognition. This paper proposed a method of generation of high resolution ISAR images by synthesizing frequency spectrums of each stepped chirp waveform in one burst and sub-sampling in frequency domain. This process is performed over entire bursts during coherent processing interval. Conventional ISAR image generation method using stepped frequency waveform has a severe problem of short unambiguous range, loading to ghost phenomenon. However, this problem can be resolved by the proposed method. In simulations, we generate high resolution ISAR image of the moving target which is Boeing-737 aircraft model composed of several ideal point scatterers.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.1
• /
• pp.59-64
• /
• 2016

In this study, the application was developed for the simulation of functional electrical stimulation. It functions to calculate the electrical energy which is transmitted to the patient, to visualize the electrical stimulation waveform, Therapy, Burst and Pulse section as setup of time period requested. The application was verified by comparing the oscilloscope and the graph of the application. XML schema was developed to utilize the contents of simulation which consist of the standard codes that are identified by OID. Using the application, medical experts will be able to research and share the contents of simulation.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.79-86
• /
• 1995

The structural materials for cryogenic technology have been recently developed to support the many modern large-scale application from superconducting magnets for nuclear fusion reactor, magnetic levitation railway to LNG tankers. However it is pointed out that quenching phenomenon is one of the serious problems for the integrity of these applications, which is mainly attributed to the rapid temperature rising in the material due to some extrinsic factors of structures. From the viewpoint of fracture mechanics, it is therefore very important to clarify the mechanism of temperature rising of structural material due to cyclic loading at cryogenic temperature. From this purpose, fatigue test was carried out for high manganese steel at liquid helium temperature(4.2K) using triangular stress waveform to identify both the mechanism of temperature rising near crack tip and the effect of loading stress waveform on temperature rising near crack tip and the effect of loading stress waveforms on temperature rising. As the results, two types of temperature rising, that is, regular and burst types were observed. And a periodical temperature rising corresponding to the stress waveforms was also found. The peaks of the temperature rising were recorded near both the maximum and the minimum values of the applied stress. The sudden temperature rises, which indicated the higher values than those of periodical temperature rises under the repetition of stress, were observed at the final region of crack growth. It was shown that the peak values of the temperature rising increased with stress intensity factor range.