• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.764-767
• /
• 2001

Because using LB method, result that produce Arachidic acid and Stearic acid LB film and measure the accumulation characteristic and electrical characteristic is as following. Organic monolayers of surface of the water compression each 9 layer's LB film to slide glass and manufactured MIM device compressing molecular film only. Could confirm that accumulation was good seeing as absorption coefficient and SEM picture, AFM picture that prevent manufactured LB films. Formation of domain of coexistence form that prevent LB film is indefinite and distinction of border side was not clear, and could know that roughness appears greatly. Obtained current by applied voltage could know that is proportional almost, though Arachidic acid appeared as bulk of current that happen in equaler certification voltage than Stearic acid is less, this alkyl chain longer Arachidic acid that serving relations special quality is superior know can .

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.547-549
• /
• 2001

The dielectric constants and dielectric losses of ZrTiO$_4$thin films deposited by DC magnetron reactive sputtering were investigated. The paraelectric properties were measured in the 100kHz range. As the deposition temperature increased (up to 67$0^{\circ}C$), the dielectric losses (tan$\delta$) decreased (down to 0.017$\pm$0.007), while the dielectric constants ($\varepsilon$) were in the range of 35$\pm$7. Post annealing at 80$0^{\circ}C$ in oxygen for 2h reduced tan$\delta$ down to 0.005$\pm$0.001, higher than those of well-sintered bulk ZrTiO$_4$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.889-891
• /
• 1998

Copper films have been deposited on glass substrate via a thermal decomposition of copper(II) formate using a focused $Ar^+$ laser emitting at 514 nm. The growth kinetics of these Cu films was investigated as a function of laser power and scan speed which varied in the range of 70-150 mW and 0.1-20 mm/s, respectively. The resistivity of the copper films was a factor of about 20 higher than· that of bulk value, but the resistivity decreased due to changes in morphology and porosity of the deposit after annealing at $300^{\circ}C$, 5 min. and was about $10{\mu}{\Omega}cm$.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2007년도 춘계학술대회
• /
• pp.251-251
• /
• 2007

• 한국전기전자재료학회논문지
• /
• 제15권8호
• /
• pp.736-741
• /
• 2002

Phase intergrowth some kinds of the $Bi_2Sr_2Ca_{n-1}Cu_nO_y$ phases is observed in the thin film fabrication at ultralow co-deposition with multi targets by means of ion beam sputtering. The molar fraction of the Bi2212 phase in the mixed crystal of the grown films is investigated as a function of the applied ozone pressure and the substrate temperature. The activation energy for the phase transformation from the Bi2201 to the Bi2212 is estimated in terms of the Avrami equation. This study reveals that the formation of a liquid phase contributes significantly to the construction of the Bi2212 phase in the thin films, differing from the bulk synthesis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.490-493
• /
• 2002

Phase intergrowth some kinds of the Bi$_2$Sr$_2$Ca$\_$n-1/Cu$\_$n/O$\_$y/ phases is observed in the thin film fabrication at ultralow co-deposition with multi targets by means of ion beam sputtering. The molar fraction of the Bi2212 phase in the mixed crystal of the grown films is investigated as a function of the applied ozone pressure and the substrate temperature. The activation energy for the phase transformation from the Bi2201 to the Bi2212 is estimated in terms of the Avrami equation. This study reveals that the formation of a liquid phase contributes significantly to the construction of the Bi2212 phase in the thin films, differing from the bulk synthesis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.880-883
• /
• 2003

ZnO thin films for Film Bulk Acoustic Resonator(FBAR) were prepared by FTS (Facing Target Sputtering) system. The FTS methode enable to generate high density plasma, and it has a high deposition rate at 1mTorr pressure. Therefore, the ZnO thin films were deposited on $AZO/SiO_2/Si$ substrates with oxygen gas flow rate, and the other sputtering conditions were fixed such as a sputtering current of 0.8A, a substrate temperature at room temperature. AZO bottom electrode were deposited on $SiO_2/Si$ substrate and by Zn:Al(Al:2wt%) metal target. ZnO thin film thickness and the c-axis preferred orientation of ZnO thin film were evaluated by ${\alpha}-step$ and XRD.

• 전자공학회논문지A
• /
• 제29A권8호
• /
• pp.56-62
• /
• 1992

This paper is analyzed the charge trapping and electrical properties of 0(Oxide), NO(Nitrided oxide) and ONO(Reoxidized nitrided oxide) as dielectric films in MIS structures. We have processed bottom oxide and top oxide by the thermal method, and nitride(Si$_{3}N_{4}$) by the LPCVD(Low Pressure Chemical Vapor Deposition) method on P-type(100) Silicon wafer. We have studied the charge trapping properties of the dielectrics by using a computer controlled DLTS system. All of the dielectric films are shown peak nearly at 300K. Those are bulk traps. Many trap densities which is detected in NO films, but traps. Many trap densities which is detected in NO films. Varing the nitride thickness, the trap densities of thinner nitride is decreased than the thicker nitride. Finally we have found that trap densities of ONO films is affected by nitride thickness.

• 한국정밀공학회지
• /
• 제28권2호
• /
• pp.245-250
• /
• 2011

A high-resolution shadow mask, a nanostencil, is widely used for high resolution lithography. This high-resolution shadowmask is often fabricated by a combination of MEMS processes and focused ion beam (FIB) milling. In this study, FIB milling on 500-nm-thin SiN membrane was tested and characterized. 500 nm thick and $2{\times}2$ mm large membranes were made on a silicon wafer by micro-fabrication processes of LPCVD, photolithography, ICP etching and bulk silicon etching. A subsequent FIB milling enabled local membrane thinning and aperture making into the thinned silicon nitride membrane. Due to the high resolution of the FIB milling process, nanoscale apertures down to 60 nm could be made into the membrane. The nanostencil could be used for nanoscale patterning by local deposition through the apertures.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2007년도 추계종합학술대회
• /
• pp.211-214
• /
• 2007

In this paper, the resonance characteristics of ZnO-based film bulk acoustic resonator (FBAR) devices with thick bottom electrode are investigated. The ultra-thin Cr film (300 ${\AA}-thick$) between $SiO_2$ film and W film is formed by a sputtering-deposition in order to enhance the adherence at their interfaces. The resonance frequency of three different resonator devices was observed to be ${\sim}2.7$ GHz, and the resonance characteristics $(S_{11})$ of the FBAR devices were found to have a strong dependence on the thickness of bottom electrode.