• Toxicological Research
• /
• v.13 no.1_2
• /
• pp.87-94
• /
• 1997

This study was carried out to investigate toxicity of insecticide carbofuran and compensatory effects of phenobarbital sodium (PB) in vivo and in vitro. Sprague Dawley male rats were used as experimental animals and divided into carbofuran only administered group and simultaneous application group of carbofuran and PB. At 30 rain and 1, 3, 6, 12, 24, 48 and 96 hrs after each treatment, the animals were sacrificed by decapitation. Kidney were immediately removed, immersed in fixatives, and processed with routine method for light microscopic study. Paraffin sections were stained with H-E, PAM and PAS. $5.0\times 10^4$ cell/ml of NIH 3T3 fibroblast in each well of 24 multidish were cultured: After 24 hours, the cells were treated with solution of six groups; control group cultured in media only, carbofuran $MTT_50$ or $NR_50$ group cultured in the media containing carbofuran $MTT_50$ or $NR_50$ and four experimental groups cultured in the media containing carbofuran $NR_50$ plus various concentratins of PB. After the NIH 3T3 fibroblast of all groups were cultured in same condition for 48 hours, Tetrazolium MTT (MTT) and NR (neutral red) assay were performed to evaluate the cytotoxicity of cell organelles. Under the light microscope, atrophic change of renal corpuscles were frequently observed in 1 and 2 days after carbofuran treatment. The increase of the mesangium was apparent in 1 and 2 days after carbofuran treatment. Necrotic changes of the epithelium and loss of brush border of proximal tubules were most severe at 2 and 3 days after carbofuran treatment, respectively. In contrast, there were no evidences of the toxic effects on renal tissues at 48hrs in carbofuran-PB treated groups. Carbofuran $MTT_50$ and $NR_50$ were 78$\mu M$, 82.5$\mu M$ respectively. MTT and NR quantities were significantly increased in carbofuran-PB 100$\mu M$ treatment group and carbofuran-PB 100$\mu M$ treatment group. On the basis of these results, it is obvious that PB has compensatory effects against carbofuran toxicity.

• Journal of Korean Academy of Nursing
• /
• v.38 no.1
• /
• pp.39-44
• /
• 2008

Purpose: The purpose of this study was to compare 1% chlorhexidine-gluconate/61% ethanol (CHG/Ethanol) emollient and 7.5% povidone-iodine (PVI) scrub for antimicrobial, residual effect, and skin condition. Method: CHG/Ethanol emollient hand hygiene was performed waterless, and brushless by operating doctors and nurses (N=20). PVI hand washing was performed with water and a brush (N=20) for 5 min. The subjects were asked to press their left hand in hand-shaped agar before a surgical scrub, immediately after a surgical scrub and after the operation. The amount of isolated microorganisms were calculated by counting the number of divided areas($1{\times}1cm$, 160 cell) which were culture positive in the hand culture plate. The skin condition was evaluated. Result: The antimicrobial count of CHG/Ethanol emollient and PVI immediately post surgical scrub was 0.0 vs. 4.1 (p>.05), and after the operation was 0.1 vs. 37.8 (p>.05)respectively. The Residual effect of CHG/Ethanol emollient immediately post surgical scrub and after the operation were 0.0 vs. 0.1 (p>.05), and PVI were 4.1 vs. 37.8 (p>.05)respectively. The skin condition and satisfaction of CHG/Ethanol emollient was higher than PVI (p<.05). Conclusion: The antimicrobial effect between CHG/Ethanol emollient and PVI were the same. Considering skin condition, satisfaction and allergic reaction CHG/Ethanol emollient for surgical scrub is recommended in Korea.

• Journal of Aerospace System Engineering
• /
• v.12 no.3
• /
• pp.1-8
• /
• 2018

The fuel pump, which is used for an aircraft, was first developed in Korea through the Civil-Military Dual Components Development Program. The BLDC motor type, which is superior to the DC brush motor when considering efficiency, endurance, and explosive environmental characteristics, was applied to the fuel pump given its capacity and operating condition. The magnetic flux of the permanent magnet was analyzed based on the magnet flux density equation, using the Maxwell equation and the environmental condition. The motor performance, according to the load, was analyzed using the finite element method in order to design validation. The motor assembly was developed by designing the motor drive and the EMI filters. The performance test results of the motor assembly for the fuel boost pump were consistent with the analysis.

• The Korean Journal of Physiology
• /
• v.28 no.2
• /
• pp.203-214
• /
• 1994

Using the methods of stopped-flow and epifluorescence microscopy with entrapped fluorophore, membrane permeability of $NH_3$ and weak acids in liposomes, renal brush border (BBMV) and basolateral membrane vesicles (BLMV), and primary culture cells from renal proximal tubule was measured. Permeability coefficient (cm/sec) of $NH_3$ was $(2.9{\times}10^{-2}$ in phosphatidylcholine liposome $25^{\circ}C)$, $5.9{\times}10^{-2}$ in renal proximal tubule cell $(37^{\circ}C)$, $4.0{\times}10^{-2}\;and\;2.4{\times}10^{-2}$ in BBMV and BLMV $(25^{\circ}C)$, respectively. Formic acid has the highest permeability coefficient among the weak acids tested, which was $4.9{\times}10^{-3}$ in liposome, $5.0{\times}10^{-3}$ in renal proximal tubule cell, $9.1{\times}10^{-3}$ in BBMV and $3.8{\times}10^{-3}$ in BLMV. There was a linear relationship between external concentration of nonionized formic acid and initial rate of flux of formic acid in liposome, and the slope coincided with the value of permeability coefficient of formic acid measured in pH 7.0. These results show that techniques of stopped-flow and epifluorescence microscopy with entrapped fluorophore provide the precise method of measurement of very rapid transport of nonelectrolytes through membranes with the advantages of instantaneous mixing effect, good resolution time and easy manipulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.918-921
• /
• 2002

Some investigators who have tried to achieve the highly smooth surface finish using electrochemical processes have reported that high current density produced lustrous surfaces while the opposite conditions produced a passive layer and had a tendency to produce a black surface. However, processing at a low current density may produce a non-lustrous surface but the improvement of dimensional accuracy of the surface is significant. The surface with pulse process was a bit more lustrous than with continuous current but the black passive layer still could be found at grooved surface. There are two ways to achieve highly smooth surface finish. One is brushing it with a brush the other is electrochemical machining (ECM) with high current. The former method is the most common polishing practice, but not only may the surface obtained differ from operator to operator, but precision smooth surface on micro grooves are difficult to obtain. The latter one recently has been used to produce a highly smooth surface after EDM process. However, the material removal rate in ECM with high current is relatively high. Hence the original shape of the micro grooves, which was formed by electrochemical micro-machining (EMM) process, may be destroyed. In this study, an electrochemical polishing process using pulse current is adopted as a possible alternative process when micro grooves formed by EMM process should be polished. Mirror-like micro grooves with lustrous and smooth surface can be produced electrochemically with pulse current because the voltage and current used can be lower than the case of continuous current. This study will discuss the accurate control of physical and electrical conditions so as to achieve mirror-like micro grooves with lustrous and smooth surface without destroying the original shape of micro grooves.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.3
• /
• pp.373-378
• /
• 2012

The purpose of this study was to develop an electric riding machine for cycle fitting to control riding posture easily, to measure frame size quantitatively, and to overcome disadvantages of the traditional systems. The electric riding machine consisted of actuator, load controller, and display & control unit. The actuator unit by BLDC(BrushLess Direct Current) motor drives the saddle height up and down, the crank forward and backward, the handlebar up and down, and the handlebar forward and backward. The load controller unit controls loads by Eddy current controller with electromagnet and aluminum circular plate. The display & control unit consisted of frame size controller and display panel which shows top tube length(485~663mm), head tube length(85~243mm), seat tube length(481~671mm), and seat tube angle($62.7{\sim}76.4^{\circ}$). The range of frame size control for developed electric riding machine did not have difference compared to traditional commercial systems, but quantitative and precise control with 0.1 mm length and $0.1^{\circ}$ angle was possible through digital measurement. Unlike traditional commercial systems, frame size control was possible during riding through motor driven method, thus fitting duration decreased. It is necessary for further improvement to have feedback from users. It is believed that developed electric riding machine can help to develop domestic fitting system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.6
• /
• pp.1333-1337
• /
• 2011

3D engines loading, and expansion of the usable capacity, next-generation smartphone game markets are rising briskly by the improvement in CPU processing speed of Phones (hardware of smartphone). Therefore, in creating 3D game characters, realistic and free-form animations in a small screen of a smartphone are becoming important. Through this paper, as a method of creating characters and operating for game characters to cause user's feeling, with NURBS data of MAYA, We completed a face in turns of eyes, a nose, and a mouth, and with Polygon Cube tool, modeled hands and feet. After dividing a cube into half and modeling it, through mirror copying We completed the whole body and modeled the low-polygon. Then to model realistic and free-form characters, We completed each detail with ZBrush and applied Divide level up to 4. Though they might look rough and exaggerated, We tried to express stuck-out parts and fallen-in parts effectively and smoothly with Smooth brush effect, map and design the low-polygon 3D characters.

• Toxicological Research
• /
• v.17 no.2
• /
• pp.123-129
• /
• 2001

This study were carried out to investigate cytotoxicity of paraquat and bentazon that is scattering to farm products were essensial for human diet and compensatory effects of 3-methylcholanthrene (3-MC) in vitro and in vivo. In vitro, The 5.0$\times$$10^4$ cell/ml of NIH 3T3 fibroblast in each well of 24 multidish were cultured. After 24 hours, the cells were treated with solution of paraquat and bentazon (1, 25, 50, 100 pM respectively). After the NIH 3T3 fibroblast of all groups were cultured in same condition for 48 hours, Sulfohordamin B Protein (SRB) assay were performed to evaluate the cytotoxicity of cell organelles. Paraquat and bentazon $SRB_50$ were 1860.73 $\mu\textrm{M}$, 1913.38 $\mu$M respectively. In vivo, Sprague Dawley male rats divided into paraquat and bentazon only administered group and simultaneous application group of paraquat and bentazon and 3-MC. At 30 min. and 1, 3, 6, 12, 24, 48 and 96 hrs. interval after each treatment, the animals were sacrificed by decapitation and kidney were immediately removed, immersed in fixatives, and processed with routine method for light microscopic study. Paraffin sections were stained with H-E, PAM, and PAS. Under the light microscope, atrophic change of renal corpuscles were frequently observed from 3 hrs after paraquat and bentazon treatment. The increase of the mesangium was apparent from 12 hrs later after paraquat and bentazon treatment. Necrotic changes of the epithelium and loss of brush border of proximal tubules were most severe at 48 hrs after paraquat and bentazon treatment, respectively. In contrast there were no evidences of the toxic effects on renal tissues at 48hrs in paraquat and bentazon plus 3-MC treated groups.

• International Journal of Vascular Biomedical Engineering
• /
• v.2 no.1
• /
• pp.17-24
• /
• 2004

Tumor angiogenesis was simulated using a two-dimensional computational model. The equation that governed angiogenesis comprised a tumor angiogenesis factor (TAF) conservation equation in time and space, which was solved numerically using the Galerkin finite element method. The time derivative in the equation was approximated by a forward Euler scheme. A stochastic process model was used to simulate vessel formation and vessel elongation towards a paracrine site, i.e., tumor-secreted basic fibroblast growth factor (bFGF). In this study, we assumed a two-dimensional model that represented a thin (1.0 mm) slice of the tumor. The growth of the tumor over time was modeled according to the dynamic value of bFGF secreted within the tumor. The data used for the model were based on a previously reported model of a brain tumor in which four distinct stages (namely multicellular spherical, first detectable lesion, diagnosis, and death of the virtual patient) were modeled. In our study, computation was not continued beyond the 'diagnosis' time point to avoid the computational complexity of analyzing numerous vascular branches. The numerical solutions revealed that no bFGF remained within the region in which vessels developed, owing to the uptake of bFGF by endothelial cells. Consequently, a sharp, declining gradient of bFGF existed near the surface of the tumor. The vascular architecture developed numerous branches close to the tumor surface (the brush-border effect). Asymmetrical tumor growth was associated with a greater degree of branching at the tumor surface.

• Journal of Biosystems Engineering
• /
• v.35 no.5
• /
• pp.330-335
• /
• 2010

Soybean (Glycine max Merr.) and corn (Zea mays L.) transplanting has increased because soybean and corn crops cultivated by the direct seeding method were often damaged by wild birds. The purpose of this study is to develop a seeder to sow soybean (Glycine max Merr.) and corn (Zea mays L.) in a plug tray. In order to find out design factors for a metering device of the seeder, metering characteristics on metering hole size and roller speed were experimentally investigated. Soybean (cv. 'Daewon') and corn (cv. 'Mibaekchal') were used as a materials for testing the seeder in this experiment. The metering hole size of roller suitable for Daewonkong and Mibaekchal was determined. Daewonkong was suitable for hole diameter of 10 mm and hole depth of 5.5 mm, and Mibaekcal was suitable for hole diameter of 9 mm and hole depth of 5.5 mm. At a brush length of 4 mm, one grain seeding rates of Daewonkong and Mibaekchal was 99% and 93% respectively. By inducing Mibaekchal to the hole by swing, one grain seeding rate of that increased from 91.9% to 97.7%. When roller speed is 4 m per minut, seeding efficiency of prototype was 110 sheets per hour.