• Steel and Composite Structures
• /
• 제49권2호
• /
• pp.215-230
• /
• 2023

Cable-girder anchorage joint is the critical part of cable-supported bridges. Tensile-plate anchorage (TPA) is one of the most commonly used types of cable-girder anchorage joints in steel girder cable-supported bridges. In recent years, it has been proposed by bridge designers to apply TPA to concrete girder cable-supported bridges to form composite cable-girder anchorage joint (CCGAJ). In this paper, the mechanical performance of CCGAJ under tensile force is studied through experimental and numerical analyses. Firstly, the effects of the external prestressing (EP) and the bearing plate (BP) on the mechanical performance of CCGAJ were investigated through three tests. Then, finite element model was established for parametrical study, and was verified by the experimental results. Then, the effects of shear connector forms, EP, BP, vertical rebar rate, and perforated rebar rate on the tensile capacity of CCGAJ were investigated through numerical analyses. The results show that the tensile capacity of CCGAJ depends on the first row of PR. The failure mode of CCGAJ using headed stud connectors is to form a shear failure surface at the end of the studs while the failure mode using PBLs is similar to the bending of a deep girder. Finally, based on the strut-and-tie model (STM), a calculation method for CCGAJ tensile capacity was proposed, which has a high accuracy and can be used to calculate the tensile capacity of CCGAJ.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.770-773
• /
• 2004

The full-width, full-depth precast panel system is very efficient for the rehabilitation of deteriorated decks as well as for new bridge construction.. The horizontal bond strength at the interface between the two interconnected elements is of primary importance in order to achieve composite action. The strength of the bond between the two precast members should be high enough to prevent any progressive slip from taking place. However, the case when both of the interconnected elements are precast members bonded by means of grout, is not currently addressed by KBDC or AASHTO. This is the main impetus for this study. A total 43 push-off tests were performed to evaluate the horizontal bond strength and to recommend the best practice for the system. Test parameters included different interface surface conditions, different amount and different types of shear connectors. The presence of the shear keys at the top surface of the beam increased the interface bond capacity tremendously compared to the bond capacity with a different surface conditions.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.295-302
• /
• 2000

Slab guideway, surface treatment, heat line installation, and joint connection for Automated Guideway Transit with rubber tire are researched. While the AGT with rubber tire is constructed in city, the precast slab guideway must be considered a reduction of the construction period and the noise under construction. which related with environment. To do that, a basic design and the structural analysis for the precast slab guideway with rubber tire are studied. The surface treatment and the heat line installation of that are also compared with currently used methods. Tining method is applied to the surface treatment adopted from the concrete pavement application currently in use. The connection method between the slab of bridge and precast guideway are suggested with a bolt type and a bond type. To minimize noise and vibration of the connection while the AGT is in driving, the slop connection method can be enhanced the serviceability.

• Journal of Mechanical Science and Technology
• /
• 제20권11호
• /
• pp.1942-1949
• /
• 2006

Typically, condensate forms as droplets on the fin surfaces and may bridge the space between the fin surfaces. This is due to the dry characteristics inherent to the fin surface. The droplets increase the air-side pressure drop. In the case of high air velocities, these droplets may be blown off the fins and entrained in the air stream. To minimize the formation of condensate droplet, the wet ability of the fins must be improved. The carry-over velocity is affected by fin surface characteristics. To avoid carry-over in the air conditioner having the highest air velocity of 1.5 m/sec, the dynamic contact angle (DCA) should be at least lowly under $60^{\circ}$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.721-725
• /
• 1996

The microfabricated test structures were used in order to evaluate the stress characteristics in films. The test structures were fabricated using surface micromachining technique, including HF vapor phase etching as an effective release method. The fabricated structures were micro strain gauge, cantilever-type vernier gauge and bridge for stress measurement, and cantilever for stress gradient measurement. The strain was measures by observing the deformation of the structures occurred after release etching and the amount of deformation can be detected by micro vernier gauge, which has gauge resolution of 0.2${\mu}{\textrm}{m}$. The detection principles and the degree of precision for the measured strain were also discussed. The characteristics of residual stress in LPCVD polysilicon films were studied using these test structures. The stress gradient due to the stress variation through the film thickness was calculated by measuring the deflection at the cantilever free end.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.335-336
• /
• 2018

This study discusses the development of asphalt based waterproofing sheet applied on the blind side of the concrete substrate. The inorganic coating membrane is applied on top of the waterproofing sheet surface for protection, and adhesive bond to the concrete substrate surface is secured via hydration reaction the cement. The study reveals the experimental results of the overlap section tensile strength to observe the effects of the adhesion strength of this material.

• 천문학회지
• /
• 제45권1호
• /
• pp.19-24
• /
• 2012

Microthermal fluctuations are introduced by atmospheric turbulence very near the ground. In order to detect microthermal fluctuations at Fuxian Solar Observatory (FSO), a microthermal instrument has been developed. The microthermal instrument consists of a microthermal sensor, which is based on a Wheatstone bridge circuit and uses fine tungsten filaments as resistance temperature detectors, an associated signal processing unit, and a data collection, & communication subsystem. In this paper, after a brief introduction to surface layer seeing, we discuss the instrumentation behind the microthermal detector we have developed and then present the results obtained. The results of the evaluation indicate that the effect of the turbulent surface boundary layer to astronomical seeing would become sufficiently small when installing a telescope at a height of 16m or higher from the ground at FSO.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.7-8
• /
• 2014

Latex-modified concrete using ready mix concrete (R-LMC) was developed for application of building construction project (specifically, the rooftop of a parking garage unable to use heavy equipments for bridge deck overlay) due to three major outstanding properties of R-LMC; bond strength, resistance of cracks at early age, and resistance of freezing and thawing. However, R-LMC at the placement stage is required to be sufficiently cured because R-LMC is very sensitive to rate of evaporation of surface moisture. This study focused on effects of different curing methods and climate condition on cracks on the surface of hardened R-LMC considering the chart of rate of evaporation of surface moisture from concrete provided by American Concrete Institute in manual for placement of latex modified concrete.

• Earthquakes and Structures
• /
• 제7권3호
• /
• pp.385-400
• /
• 2014

Pounding damage to bridges and buildings is observed in most major earthquakes. The damage mainly occurs in reinforced concrete slabs, e.g. building floors and bridge decks. This study presents the results from pounding of reinforced concrete slabs. A parametric investigation was conducted involving the mass of the pendulums, the relative velocities of impact and the geometry of the contact surface. The effect of these parameters on the coefficient of restitution and peak impact acceleration is shown. In contrast to predictions from numerical force models, it was observed that peak acceleration is independent of mass. The coefficient of restitution is affected by the impact velocity, total participating mass and the mass ratio of striker and struck block.

• 한국건설관리학회:학술대회논문집
• /
• 한국건설관리학회 2003년도 학술대회지
• /
• pp.180-185
• /
• 2003

도로를 통과하는 차량 통행량의 증가는 장기적으로 교량에 구조적인 손상을 유발시키기 때문에 교량의 유지관리 측면에서 심각한 문제로 대두되고 있으며 준공 단계부터 구조물의 유지관리에 대하여 관심을 기울이지 않으면 공용기간 중 만족할 만한 기능의 유지 및 확보는 불가능하다. 또한, 공황 중에 균열이나 변형 등과 같은 열화손상을 조기에 발견하여 기능상의 장애나 사고를 미연에 방지하기 위해서는 정기적인 점검을 통하여 유지관리를 실시해야 하나 이에 관한 관심도가 상대적으로 낮아 구조물 유지관리에 대한 새로운 인식의 전환과 이와 관련된 기술개발이 절실히 요구되고 있다. 본 연구는 현재 굴절차 또는 점검차에 점검 인력이 직접 탑승하여 실시하는 육안조사를 대체하기 위하여 작은 카메라가 부착된 로봇(Machine Vision System)이 장착된 Linear Motion Control of System을 교량 하부에 설치하고 작업자는 교량 상부에서 외관조사를 수행함으로써 점검자에 따라 주관적으로 점검결과가 도출되는 문제를 근본적으로 해결하고 점검시 안전성을 대폭 개선하며 화상에 검측된 열화 손상 자료를 이미지 프로세싱 기법을 이용하여 객관적이고 정량적인 자료로 저장 및 제공함으로써 교량 유기관리시스템을 위한 데이터베이스를 구축하는데 기여할 수 있는 교량 하부 외관조사 자동화 시스템을 개발하는 데에 그 목적을 두고 있으며 본 시스템을 통하여 교량의 보수 보강 시기를 보다 객관적으로 산정할 수 있어서 현재 매년 기하급수적으로 늘어나는 교량의 보수 보강 비용을 상당히 절감할 수 있을 것으로 기대된다.저장기간을 계산하면, 아세설팜칼륨의 혼용 비율이 높아질수록 저장기간이 길어져서, $50\%$로 혼용하였을 때 가장 긴 저장기간이 산정되어 $20^{\circ}C$에서는 178일, $30^{\circ}C$에서는 88일이 예측되었다. 아스파탐과 아세설팜칼륨의 혼용비율을 5:5, 7:3, 9:1로 달리하여 구연산 완충액 상에 녹인 후, 20, 40, $60^{\circ}C$에서 저장하였다 크기 추정법을 이용하여 단맛을 측정한 결과 20일간의 저장 기간 동안 $20^{\circ}C$와 $40^{\circ}C$에서는 단맛이 유지되는 것으로 나타났다.산도 $0.4\~0.8\%^{(10)}$에서도 식품 유해가능성을 가진 균이 상당수 검출되므로 원료의 수송, 김치의 제조 및 유통과정에서 병원균에 대한 오염방지에 유의하여야 할 것이다. 확인할 수 있었다. 이상의 결과에 의하면 고농도의 유기물이 함유된 음식물쓰레기는 Hybrid Anaerobic Reactor (HAR)를 이용하여 HRT 30일 정도에서 충분히 직접 혐기성처리가 가능하며, 이때 발생된 $CH_{4}$를 회수하여 이용하면 대체에너지원으로 활용 가치가 높은 것으로 판단된다./207), $99.2\%$(238/240), $98.5\%$(133/135) 및 $100\%$ (313)였다. 각각 두 개의 요골동맥과 우내흉동맥에서 부분협착이나