• Journal of the Korea Concrete Institute
• /
• v.20 no.4
• /
• pp.415-421
• /
• 2008

Reinforced concrete starts to corrode when the chloride ion concentration which is the sum of included in concrete and penetrated from environments exceeds a certain level of critical chloride concentration. Therefore each country regulates the upper bounds of chloride amount in concrete and the regulations are different for each country due to its circumstances. In this study, the critical threshold chloride content according to unit cement amount is empirically calculated to propose a reasonable regulation method on the chloride amount. As a result, the critical threshold chloride content increases considerably according to cement content and it agrees with the established theories. The present regulations on total chloride amount 0.3 or 0.6 kg chloride ions per $1\;m^3$ of concrete does not reflect the influences of mix design, environmental conditions and etc. So it can be said that it is more reasonable to regulate the critical threshold chloride content by the ratio of chloride amount per unit cement content than by the total chloride content in $1\;m^3$ of concrete.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.11
• /
• pp.51-60
• /
• 2014

Load and Resistance Factor Design (LRFD) is one of the limit state design methods, and has been used worldwide, especially in North America. Also, the study for LRFD has been actively conducted in Korea. However, the data for LRFD in Korea were not sufficient, so resistance factors suggested by AASTTO have been used for the design in Korea. But the resistance factors suggested by AASHTO represent the characteristics of bedrocks defined in the US, therefore, it is necessary to determine the resistance factors for designs in Korea, which can reflect the characteristics of bedrocks in Korea. Also, the calculated probabilities of failure from conventional reliability analyses which commonly use log-normal distribution are not realistic because of the lower tail that can be extended to zero. Therefore, it is necessary to calibrate the resistance factors considering the lower-bound resistance. Thus, this study calculates the resistance factors using thirteen sets of drilled shaft load test results, and then calibrates the resistance factors considering the lower-bound resistance corresponding to a target reliability index of 3.0. As a result, resistance factors from conventional reliability analyses were determined in the range of 0.13-0.32 for the shaft resistance, and 0.19-0.29 for the base resistance, respectively. Also, the lower bounds of resistance were determined based on the Hoek-Brown failure criteria (2002) and GSI downgrading. Considering the lower-bound resistances, resistance factors increased by 0~8% for the shaft, and 0~13% for the base, respectively.

• Korean Journal of Construction Engineering and Management
• /
• v.18 no.1
• /
• pp.3-16
• /
• 2017

Integrated project delivery (IPD) is suggested as an alternative to traditional delivery methods such as design-build (DB), design-bid-build (DBB), and construction management at risk (CMR). Many foreign research studies have approached IPD not only in the contractual aspect but also the work implementation method aspect. However, most research projects in Korea have focused on the contractual aspect of IPD for asserting that the characteristics are the critical matter. The Korean institutional and legal system does not permit the multi-party agreement; therefore, it is difficult to adopt IPD in Korea's construction industry. The researchers do not wait the system to be changed, but we do identify the possibility of adopting IPD in Korea in the perspective of work implementation method, except the contractual characteristics. Thus, the goal of this research is to identify one project that does not include IPD agreement but utilizes other IPD characteristics whose contractual results have similar performance to those that utilize all characteristics of IPD including agreement. This research is expected to enhance performance of the construction project in a Korean construction environment by embracing IPD characteristics as overcoming limits and bounds of the traditional delivery method.

• Asian Journal of Turfgrass Science
• /
• v.12 no.1
• /
• pp.49-78
• /
• 1998

Nowadays, there are increasing demands of golf courses and it is necessary to make more golf courses than the present. To do this, we need to improve the environmental problems with the regional inhabitants, and it is said that the first thing to be considered in developing any golf course in Korea is to preserve the environment. In this context, the purpose of this study is to set forth several design factors to lessen the negative impacts which are accompanied with the development of golf courses. 1. The present conditions of golf courses in Korea Many new golf courses have come into being, particularly since the late 1980s, and now, in the year of 1997, over one hundred of golf courses are doing their business, yet the number of golf course is still less than required. So far, over a half of them have been made in the vicinity of Seoul on account of various reasons, and this has adversely affected on our natural environment. This unreasonable development of golf courses has caused serious water pollution, landslides and the other problems. Also, the topography of Korea is not good for golf courses. Although the demands of golf courses are increasing, the suitable sites for them are very limited, and therefore it is sometimes unavoidable to make golf courses on steep hills. Consequently, in designing golf courses in Korea, the most important thing is the balance between natural environment and artificial environment. 2.Eco-friendly golf course design factors 1) The concept of eco-friendly golf courses Ecologically sustainable and sound golf courses which are made by eco-friendly approaches 2)Basic conditions of eco-friendly golf courses (1)The most suitable sites (2) Conservation of existing ground as much as possible (3)Proper use of agricultural chemicals which have great impacts on the environment (4) Reasonable use of fertilizers (5) Developing a specialized fertilizer only for grass (6) Adaptation of organic agriculture (7) Improvement of grass sorts (8) Establishing reservoirs for purifying the water from golf courses 3) Eco-friendly golf courses (1) Location-Enough area /Gentle slope/Winding ground/Including lakes or streams /Not crossing wind's main direction Facing south or southeast /Suitable soIl for grass /Good drainage /Low level of underground water (2)Course layout and design -Consideration about existing contours as much as possible -Adaptation of Scotish design trend -Various holes' configuration -Consideration toward surrounding landscapes -Reducing grass areas -Giving buffer zones -Adapting computer methods in the process of site analysis and design (3) Eco-friendly considerations in constructing and managing golf courses -Protection of wildlife -Reuse of existing forests and preservation of topsoil -Renovation of old-fashioned courses -Reducing grass areas -Purification of water -Standization of management -Strict regulations against chemicals -Recycling organic materials -Through separation of the water inside golf courses and out of bounds -Getting proper construction works done in a due time 4.Eco-friendly considerations from a viewpoint of cultural environment 1) Well-matched landscape design and events planning 2) Implement of identifications and awarding systerns 3)Acknowledgement of superintendents' qualitications in the maintenance of golf courses 4)Increasing public golf courses and keeping good relationships with the neighbors near golf courses Key words: Pro-environmental development, Golf course.

• Geophysics and Geophysical Exploration
• /
• v.18 no.4
• /
• pp.171-180
• /
• 2015

Electrical resistivity of 23 core samples from Ulleung Island at dry or saturated condition has been measured along with dry density and effective porosity, and the relations between the properties has also been discussed. Upper and lower bounds of electrical resistivity at room temperature can be provided by the dry- and saturated-resistivity, respectively. Injecting nitrogen gas to the pore space at the very end of drying process can prevent humid air from getting into the pore space, so that measurement of dry-resistivity can be less affected by humidity in the air. Dry density and porosity have very close correlation; the ratio between increase of porosity and the decrease of density showed distinct relation to the rock types, such that basaltic rocks showed higher ratio while trachytic rocks showed lower. Saturated resistivity showed close correlation to density and effective porosity of the rock sample, while dry resistivity didn't.

• Land and Housing Review
• /
• v.1 no.1
• /
• pp.103-111
• /
• 2010

The purpose of the paper is to research issues and implications on a large-scale enlargement of urban area in city management plan. This study investigated laws and regulations in force and carried out case study for three cities such as Yangju-si, Gimpo-si, Whaseong-si. As a result of analysis, three points at issue were abstracted and improvement ideas for each of them were suggested as follows. First, to set up adequate size of urban area, it is necessary to consider resonable planning for population, spatial structure, zone of life and land use in city comprehensive plan and city management plan. Second, to decrease arguments about scope and bounds of urban area, it is important to make general and specific guidelines to set up them. Third, to manage new urban area and its surroundings efficiently, it is necessary to subdivide zoning of non-urban area strictly, to restraint individual location of factories or cattle sheds, to make a proper infrastructure plan in advance, to administer strongly the permission of development behavior and to control strictly consecutive and joining development in non-urban area.

• Korean Journal of Acupuncture
• /
• v.25 no.4
• /
• pp.31-47
• /
• 2008

Objectives : The objective of this study is to apply the contents of "WaHyul(訛穴 : The errors of acupoint locations"of "ChimGuKyungHumBang" to modern acupoint locations. Methods : The text of "WaHyul" was closely examined and analyzed. "WHO standard acupuncture point locations in the western pacific region" was reviewed based on its contents. Results : According to the analysis, the correct 少商(LU11) was mentioned as a spot appropriately distanced from the corner of the nail root under the skin. This is the most accurate and reasonable synthesis of other related texts. Furthermore, the necessity of defining the locations of all the well points was also emphasized and their locations were mentioned that could be located by the same method. There is no further discussion of other acupoints apart from descriptions of their locations from other texts. Some parts that were pointed out as common errors included not only commonly made mistakes, but errors made in acupuncture texts as were true for 神門(HT7) and 肩井(GB21). The standards of 少商(LU11), 合谷(LI4) and 足三里(ST36) presented in the WHO Standardization are not only similar to what 「WaHyul」 indicated as errors in acupoint locations, but also deviate other acupuncture texts; appropriate corrections must be made. The standard of 肩井(GB21) presents a new acupoint locating method never mentioned before in received classic acupuncture texts and so a rediscussion is in need. Other standards, such as the 絶骨(GB39), had some points of controversy, yet somewhat incomplete while HT7 did not go beyond the bounds of "WaHyul". Conclusions : "WaHyul" can be used to revise WHO standards, and has practical value in modern acupoint locating.

• Korean Journal of Materials Research
• /
• v.5 no.6
• /
• pp.748-753
• /
• 1995

Solid solution of NaNb $O_3$70 mol% and SrTi $O_3$30 mol% was single phase. A broad dielectric peak was found at about l00K. Crystal structure was analysed at room temperature and 12K using Rietveld analysis. The unit cell was assigned to have a a doubled lattice parameter of simple perovskite sturcture at room temperatue, the structure was orthorombic with space group Pmmn. At 12K, the structure was also orthorombic with space group Pnma. This structure change with temperature was due to the distortion of oxygen octahedron. This distortion of oxygen octahedron was made by the decrease of (Ti, Nb)-O bounds length with no variation of (Ti, Nb)-O-(Ti, Nb) bound angle. Therefore the broad dielectirc peak about l00K was attributed to the structural change casued by oxygen octahedron distortion.

• Journal of KIISE:Databases
• /
• v.29 no.5
• /
• pp.367-380
• /
• 2002

Due to recent increase in applications requiring huge amount of data such as spatial data analysis and image analysis, clustering on large databases has been actively studied. In a hierarchical clustering method, a tree representing hierarchical decomposition of the database is first created, and then, used for efficient clustering. Existing hierarchical clustering methods mainly adopted the bottom-up approach, which creates a tree from the bottom to the topmost level of the hierarchy. These bottom-up methods require at least one scan over the entire database in order to build the tree and need to search most nodes of the tree since the clustering algorithm starts from the leaf level. In this paper, we propose a novel top-down hierarchical clustering method that uses multidimensional indexes that are already maintained in most database applications. Generally, multidimensional indexes have the clustering property storing similar objects in the same (or adjacent) data pares. Using this property we can find adjacent objects without calculating distances among them. We first formally define the cluster based on the density of objects. For the definition, we propose the concept of the region contrast partition based on the density of the region. To speed up the clustering algorithm, we use the branch-and-bound algorithm. We propose the bounds and formally prove their correctness. Experimental results show that the proposed method is at least as effective in quality of clustering as BIRCH, a bottom-up hierarchical clustering method, while reducing the number of page accesses by up to 26～187 times depending on the size of the database. As a result, we believe that the proposed method significantly improves the clustering performance in large databases and is practically usable in various database applications.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.12
• /
• pp.5420-5429
• /
• 2011

The study objectively examined the effects on education results from the educational programs developed by adopting competency units of NCS(National Competency Standards)' technology sectors. The objects of the study are divided to learners and instructors. The learners were set bounds to vocational college students to take a degree and incumbent company workers. Research materials had been collected from April of 2010 to June of 2011. We use test papers and structured questionnaire for studying. And we analyzed by SPSS/WIN 17.0. we examined that student's got 1.4 point out of 3 points in their self-test paper before taking classes, below average grades in understanding contents of learning. And as frequency analysis on the after taking classes performance evaluation 62.48% of them answered they can perform their duties in better ways. On average, the company workers got 1.4 point out 3 point before taking classes. And as frequency of analysis on the performance evaluation 85.45% of them answered the can perform their duties in better ways. After instructors took classes on NCS, they gave highly 5.58 out of 7 poins about learners' job competence. On the whole, the educational programs using NCS had positive effects on education results.