• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.159-160
• /
• 2002

New S-shaped aeroelastic mesoflaps are utilized to control normal shock/boundary-layer interactions. New generation of the mesoflaps is designed f3r a better rigidness and a good flow uniformity across the ulteractions. ,Major advantages of the mesoflap system can be a better total pressure recovery downstream of the interactions due to the lambda shock structure over the flap system, and a rehabilitation of the thickened boundary layer due to bleeding through a cavity underneath the flap system. Skin friction has been measured downstream of the interactions, using the laser interferometer skin friction (LISF) meter, which optically detects the rate of thinning of an oil film applied to the test surface. Various flap-thicknesses of the S-shaped mesoflap arrays are tested, and the results are compared to the solid-wall reference case. Overall, not much difference in the level of skin friction is noticed for the S-shaped flap arrays of various thicknesses, and its level is lower than the skin friction downstream of the solid-wall interaction

• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.2116-2124
• /
• 2003

An experimental study providing additional knowledge of quasi-conical symmetry in swept shock wave/turbulent boundary-layer interactions is described. When a turbulent boundary layer on the flat plate is subjected to interact with a swept planar shock wave, the interaction flowfield far from fin leading edge has a nature of conical symmetry, which topological features of the interaction flow appear to emanate from a virtual conical origin. Surface streakline patterns obtained from the kerosene-lampblack tracings have been utilized to obtain representative surface features of the flow, including the location of the virtual conical origin. The scaling law for the sharp-fin interactions suggested by previous investigators has been reexamined for different freestream Mach numbers. It is noticed that the scaling law reasonably agrees with the present experimental data, however, that the law is not appropriate to estimate the location of the virtual conical origin. Further knowledge of the correlation for the virtual conical origin has thus been proposed.

• Journal of Mechanical Science and Technology
• /
• 제19권8호
• /
• pp.1682-1691
• /
• 2005

Direct numerical simulation database of an axial turbulent boundary layer is used to compute frequency and wave number spectra of the wall shear-stress fluctuations in a low-Reynolds number axial turbulent boundary layer. One-dimensional and two-dimensional power spectra of flow variables are calculated and compared. At low wave numbers and frequencies, the power of streamwise shear stress is larger than that of spanwise shear stress, while the powers of both stresses are almost the same at high wave numbers and frequencies. The frequency/streamwise wave number spectra of the wall flow variables show that large-scale fluctuations to the rms value is largest for the stream wise shear stress, while that of small-scale fluctuations to the rms value is largest for pressure. In the two-point auto-correlations, negative correlation occurs in streamwise separations for pressure, and in span wise correlation for both shear stresses.

• Journal of Mechanical Science and Technology
• /
• 제18권7호
• /
• pp.1258-1266
• /
• 2004

It is important to completely understand heat/mass transfer from a flat plate because it is a basic element of heat/mass transfer. In the present study, local heat/mass transfer coefficient is obtained for two flow conditions to investigate the effect of boundary layer using the naphthalene sublimation technique. Obtained local heat/mass transfer coefficient is converted to dimensionless parameters such as Sherwood number, Stanton number and Colburn j-factor. These also are compared with correlations of laminar and turbulent heat/mass transfer from a flat plate. According to experimental results, local Sherwood number and local Stanton number are in much better agreement with the correlation of turbulent region rather than laminar region, which means analogy between heat/mass transfer and momentum transfer is more suitable for turbulent boundary layer. But average Sherwood number and average Colburn j-factor representing analogy between heat/mass transfer and momentum transfer are consistent with the correlation of laminar boundary layer as well as turbulent boundary layer.

• 설비공학논문집
• /
• 제15권11호
• /
• pp.895-901
• /
• 2003

Direct numerical simulation database of an axial turbulent boundary layer is used to compute frequency and wave number spectra of the wall shear-stress fluctuations in a low-Reynolds number axial turbulent boundary layer. One-dimensional and two-dimensional power spectra of flow variables are calculated and compared. At low wave numbers and frequencies, the power of streamwise shear stress is larger than that of spanwise shear stress, while the powers of both stresses are almost the same at high wave numbers and frequencies. The frequency/streamwise wave number spectra of the wall flow variables show that large-scale fluctuations to the ms value is largest for the streamwise shear stress, while that of small-scale fluctuations to the rms value is largest for pressure. In the two-point auto-correlations, negative correlation occurs in streamwise separations for pressure and spanwise shear stress, and in spanwise correlation for both shear stresses.

• 한국가시화정보학회지
• /
• 제9권2호
• /
• pp.61-65
• /
• 2011

Several previous works on rocket nozzle flows have revealed the existence of the transition from FSS to RSS and the occurrence of asymmetric flow associated with the boundary layer separation, which can cause excessive side-loads of the propulsion system. Thus, it is of practical importance to investigate the asymmetric flow behaviors of the propulsion nozzle and to develop its control method. In the present study, the asymmetric flow control method using a cavity system was applied to supersonic nozzle flow. Time-dependent asymmetric flow was experimentally investigated with the rate of change of the nozzle pressure ratio. The results obtained showed that the cavity system installed on nozzle wall would be helpful in fixing the unsteady motions of the boundary layer separation, consequently reducing the possibility of the occurrence of the asymmetric flow.

• 대한기계학회논문집B
• /
• 제25권11호
• /
• pp.1476-1482
• /
• 2001

Turbulent boundary layer over a flat plate was disturbed by installing an elliptic cylinder with an axis ratio of AR=2. For comparison, the same experiment was carried out for a circular cylinder having the same vertical height. The surface pressure and the heat transfer coefficient on the flat plate were measured with varying the gap distance between the elliptic cylinder and the flat plate. The mean velocity and the turbulent intensity profile of the streamwise velocity component were measured using a hot-wire anemometry. As a result, the flow structure and the local heat transfer rate were modified by the interaction between the cylinder wake and the turbulent boundary layer as a function of the critical gap ratio where the regular vortices start to shed. For the elliptic cylinder, the critical gap ratio is increased and the surface pressure on the flat plate is recovered rapidly at downstream location, compared with the equivalent circular cylinder. The maximum heat transfer rate occurs at the gap ratio of G/B = 0.5, where the flow interaction between the lower shear layer of the cylinder wake and the turbulent boundary layer is strong.

• 설비공학논문집
• /
• 제17권9호
• /
• pp.799-807
• /
• 2005

The flow characteristics and the heat transfer rate on a surface by the interaction of a pair of vortices are studied numerically. To analyze the common flow up produced by vortex generators in a rectangular channel flow, the pseudo-compressibility viscous method is introduced into the Reynolds-averaged Navier-Stokes equation for 3-dimensional unsteady, incompressible viscous flows. To predict turbulence characteristics, a two-layer $k-\varepsilon$ turbulence model is used on the flat plate 3-dimensional turbulence boundary The computational results predict accurately Reynolds stress, turbulent kinetic energy and flow field generated by the vortex generators. The numerical results, such as thermal boundary layers, skin friction characteristics and heat transfers, are also reasonably close to the experimental data.

• 대한기계학회논문집B
• /
• 제25권3호
• /
• pp.330-338
• /
• 2001

This paper is concerned with the effect of cylinder wakes upstream on blade characteristics of compressor cascade(NCA 65 series). At first, it is found that the velocity defect ratio of cylinder wake varies according to the acceleration and deceleration in a flow field but, is conserved nearly constant at flow downstream the cascade, irrespective of the flow path in the cascade. When a cylinder wake flows along near the suction surface of the blade, or impinges on the leading edge, the turbulent velocities are supplied on or inside the outer edge of boundary layer near the leading edge of suction surface, and the transition to a transitional or turbulent boundary layers is induced, so that the laminar separation is prevented, but the profile loss increases. The transition of boundary layer to a transitional or turbulent one is strongly related with the strength of added turbulent velocities near the leading edge on the suction surface, which is influenced by the flow path of a cylinder wake.

• 한국항공우주학회지
• /
• 제47권10호
• /
• pp.720-727
• /
• 2019

하이브리드 로켓 연소의 저주파수 연소불안정은 고체연료의 열적지연(Thermal Lag)과 경계층 유동 변화에 의한 열전달 진동의 공진에 의해 발생한다. 본 연구는 연료 표면 근처의 경계층 유동의 교란이 어떤 물리적 과정에 의해 발생하여 연소불안정으로 발달하는지를 실험적으로 확인하였다. 특히 산화제의 스월 분사는 연소 안정화에 매우 큰 기여를 하므로 스월 강도를 증가시키며 경계층의 변화와 연소불안정의 발생과정을 연구하였다. 경계층 섭동을 확인하기 위하여 연소 유동장을 가시화하였고 이미지에 대한 POD(Proper Orthogonal Decomposition) 분석을 시도하였다. 스월 강도가 증가할수록 500Hz 대역 고주파수 p', q'의 결합이 약해지며 열적지연과 유사한 주파수 특성을 갖는 Rayleigh Index의 섭동 발생도 약해져 경계층 진동의 발생이 점차 감소하는 것을 관찰하였다. 따라서 고주파수 p', q'의 주기적인 결합에 의한 축 방향 경계층 진동이 나타나면 열적지연 주파수와 공진에 의한 연소불안정이 발생함을 확인하였다.