• Korean Journal of Metals and Materials
• /
• v.46 no.6
• /
• pp.329-337
• /
• 2008

During the continuous casting of boron-bearing steel, the corner cracks on the slab are formed by deformation with low strain rate and rapid cooling at the unbending temperature within the range of 800- $1000^{\circ}C$. Especially, the rapid cooling in the corner of slab during the continuous casting leads to as corner cracking. Therefore, in this study, the hot tensile tests applied to the different cooling rates were taken into account in order to study the effect of cooling rate on the hot ductility of boron-bearing steel. The results revealed that increasing cooling rate deteriorate the hot ductility of boron- bearing steel. Rapid decreasing of the hot ductility is caused by formation of a film-like ferrite and precipitate at the austenite grain boundaries. The morphology of the precipitates in the boron-bearing steel was monitored by PTA (Particle Tracking Autoradiography) and TEM, we observed MnS and BN compound and their morphology was quite different depending on the cooling rates. When the cooling rate is increased, rodshape MnS and BN precipitates can be formed along the austenite grain boundaries. It can cause that weakening the boundary region and decreasing the hot ductility of boron-bearing steel.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.5
• /
• pp.241-247
• /
• 2013

Hardenability and mechanical properties of boron-bearing steels containing C, Mo and Cr were investigated in this study. Using quench dilatometer, the steel specimens were cooled down to room temperature at different cooling rates to construct continuous cooling transformation diagrams and then the transformation products from austenite were examined. A critical cooling rate was introduced as an index to quantitatively evaluate the hardenability. The C addition to boron-bearing steels did not significantly affect hardenability compared to boron-free steels although it increases the hardenability. With the same content, the Mo addition largely increased the hardenability of boron-bearing steels than the Cr addition because it decreased both the transformation start and finish temperatures at low cooling rates. In particular, the Mo addition completely suppressed the formation of eutectoid ferrite even at the slow cooling rate of $0.2^{\circ}C/s$, whereas the Cr addition nearly suppressed it at the cooling rates above $3^{\circ}C/s$.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.302-305
• /
• 2009

This paper examines the effect of nitride formation on formability for Cu bearing high strength extra low carbon (ELC) steel sheets. For this purpose, we have investigated the effect of addition of aluminium (Al) and boron (B) on texture and precipitation behavior of the ELC steel during continuous annealing. Mechanical properties and microstructures of the ELC steel sheets were analyzed as well using uni-axial tensile test, electron back-scattered diffraction (EBSD) technique and transmission electron microscopy (TEM) following pilot rolling and continuous annealing. It has been found that the addition of Al and B increases the precipitation of AlN and BN. What is more, the scavange of solute nitrogen is effective in increasing the formability of the ELC steels. In addition, the Al and B addition improves the aging property of the ELC steel.

• Tribology and Lubricants
• /
• v.39 no.6
• /
• pp.228-234
• /
• 2023

In this study, reciprocating wear tests are performed on AISI 52100 bearing steel to investigate its tribological behavior in a hexagonal boron nitride (h-BN) water solution. The h-BN-based aqueous lubricant is prepared using an atoxic procedure called ultrasonic sonication in pure water. Ball-on-flat reciprocating sliding experiments are conducted, where the ball is slewed on a fixed flat at 50-㎛ displacement. The lubricating behavior of h-BN is compared with that of deionized (DI) water. Results show that the friction coefficient is higher in h-BN testing than that in DI tests, but the results are equalized as the friction coefficient reaches a stable level. Scanning electron microscopic images reveal significant material loss in the center and mild abrasion on the edge of the wear scar in h-BN tests. However, these effects are minor in DI water situations. The results of energy-dispersive X-ray spectroscopy show that considerable oxidation occurs in the central zone of the wear scar in h-BN cases with strong adhesion and material removal. These findings reveal the importance of determining ideal circumstances that can tolerate material friction and wear.

• International Journal of Korean Welding Society
• /
• v.3 no.2
• /
• pp.40-45
• /
• 2003

A series of experiments has been carried out to investigate the effect of titanium, boron and nitrogen on the microstructure and toughness of simulated heat affected zone (HAZ) in quenched and tempered (QT) type 490MPa yield strength steels. For acquiring the same strength level, the carbon content and carbon equivalent could be lowered remarkably with a small titanium and boron addition due to the hardenability effect of boron during quenching process. Following the thermal cycle of large heat input, the coarsened grain HAZ (CGHAZ) of conventional quenched and tempered (QT) type 490MPa yield strength steels exhibited a coarse bainitic or ferrite side plate structure with large prior austenite grains. While, titanium and boron bearing QT type 490MPa yield strength steels were characterized by the microstructure in the CGHAZ, consisting mainly of the fine intragranular ferrite microstructure. Toughness of the simulated HAZ was mainly controlled by the proper Ceq level, and the ratio of Ti/N rather than titanium and nitrogen contents themselves. In the titanium­boron added QT steels, the optimum Ti/N ratio for excellent HAZ toughness was around 2.0, which was much lower than the known Ti/N stoichiometric ratio, 3.4. With reducing Ti/N ratio from the stoichiometric ratio, austenite grain size in the coarse grained HAZ became finer, indicating that the effective fine precipitates could be sufficiently obtained even with lower Ti/N level by adding boron simultaneously. Along with typical titanium carbo­nitrides, various forms of complex titanium­ and boron­based precipitates, like TiN­MnS­BN, were often observed in the simulated CGHAZ, which may act as stable nuclei for ferrite during cooling of weld thermal cycles

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.395-399
• /
• 2004

Four microalloyed steels containing B were investigated in terms of hardenability, mechanical properties and microstructure depending upon the cooling rates in order to develop the steel grade for the cold forged fasners. The alloy with the largest DI value among 4 alloys, which contains $0.12\%\;C,\;1.54\%\;Mn,\;0.65\%\;Cr,\;0.11\%V,\;0.040\%Ti\;and\;0.0033\%B$, showed the larest shift to the right hand side in the TTT diagram, implying the wide allowable cooling rate range subsequent to hot rolling in long bar processing, Mechanical tests indicated that yield strength are dependent upon the DI value in water quenched specimens but other properties showed almost the same values. In the same grade of steel, the increase in cooling rates causes the decrease in elongation but the increase in strength, reduction of area and Charpy impact values. Microstructural examination in steel grade with the larest DI values revealed martensitic structure In the water quenched state, a mixture of martensite and bainite in the oil quenched, and ferrite + pearlite in the air cooled and the forced air cooled but the latter showed finer microstructure.