• KSTLE International Journal
• /
• v.3 no.2
• /
• pp.84-89
• /
• 2002

Clearance movements of engine piston are very related to the piston impact to the engine block as well as many tribological problems. Some of the major parameters that influence these kinds of performances are piston profiles, piston offsets and clearance magnitudes. In our study, computational investigation is performed about the piston movements in the clearance between piston and cylinder liner by changing the skirt profiles and piston offsets. Our results show that curved profile and more offset magnitude to thrust side have better performance that has low side impact during the engine cycle.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.2
• /
• pp.257-269
• /
• 1996

The puropose of this study was to investigate the movement-fitness according to the surface changing of lower limb The experimental items were divided into the lower limb movements (5) and body-shapes (7). This study was done by the expansion and contraction rate consideration of length, girth Also, the lower half of body shape-change on the movements and body-shapes by flat shell was done simultaneously. The summarized findings resulted from experiments and investigation are suggested as follows; First, when commpared the expansion and contraction rate of the length and girth items, the expansion rate of the back crotch length (14~20%), hip girth (10~ 21%) and knee girth (6.2~18.5%) in rabbit leap movement was the most notable among all variables considered in this experimentation. On the others hand, the front croth length (-22~-52%) contracted remarkably. And big-thigh type was the most notable on the body-shape comparision. Second, in comparision of the expansion and contraction rate of the area on the blocks, the expansion of the hip (50~200%) and knee (51~74%) block was the most remarkable. Especially, in the sit on knees movement of the hip-down type expanded 209.4%. Third, in comparision of the lower half of body shape-change, on the movements and body- shapes by the flat shell, under the influence of knee-joint and hip-joint the shape-changs of the hip and knee block was the most notable. But the shape-change of the waist, abdomen, calf, and ankle was feeble.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4C
• /
• pp.153-162
• /
• 2009

This paper investigates the effects of excavation-induced ground movements on nearby structures, considering soil-structure interactions of different soil and structural characteristics. The response of four and two-story block structures, which are subjected to excavation-induced advancing ground movements, are investigated in different soil conditions using numerical analysis. The structures for numerical analysis are modelled to have cracks when the shear and tensile stress exceed the maximum shear and tensile strength. The response of four and two-story block structures are investigated with advancing ground movement phases and compared with the response of structures which are subjected to excavation-induced total ground movement. The response of structures is compared among others in terms of the magnitude and shape of deformations and cracks in structures for different structure and ground conditions. The results of the comparison provide a background for better understandings for controlling and minimizing building damage on nearby structures due to excavation-induced ground movements.

• International Journal of Automotive Technology
• /
• v.5 no.1
• /
• pp.23-31
• /
• 2004

Secondary movements of piston in the bore clearance are closely related to the side impact to the engine block as well as many tribological problems. Some of the major parameters that influence these kinds of movements are piston profile shapes (barrel and flat), piston pin offsets and the magnitudes of bore clearances. In our study, computational investigations are performed about the piston movements in the bore clearance by changing the skirt profiles and piston offsets. In this work, it is found that curved profile and larger offset magnitude to thrust side provide better performance that has low side impact during the engine cycle.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.4
• /
• pp.327-332
• /
• 2002

The main problems of computational complexity in object tracking are definition of objects, segmentations and identifications in non-structured environments with erratic movements and collisions of objects. The object's information as a region that corresponds to objects without discriminating among objects are considered. This paper describes the algorithm that, automatically and efficiently, recognizes and keeps tracks of interest-regions selected by users in video or camera image sequences. The block-based feature matching method is used for the region tracking. This matching process considers only dominant feature points such as corners and curved-edges without requiring a pre-defined model of objects. Experimental results show that the proposed method provides above 96% precision for correct region matching and real-time process even when the objects undergo scaling and 3-dimen-sional movements In successive image sequences.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.43 no.1
• /
• pp.1-11
• /
• 2007

It is the basic studies for productivity improvement and laborsaving of purse seine fishery. Because the seine shape is apt to be transformed in seine shooting process due to the effect of tide, this study is intended to establish 4 steps, whose flow velocity are 0, 2, 4 and 6cm/sec, in flume tank and perform the experiment to review the character. We used two model seines designed on the scale of 1 to 180 based on the power block seine, which is the mackerel purse seine generally used in the near sea of Jeju Island and triplex seine, which is the mackerel purse seine of one boat system fishing expected in the future, for the experiment, analyzed of the sinking movements on the two seines and its results are as follows. In the setting over the flow velocity 6cm/sec, experiment was impossible because of flying and transformation of seine were severe. The sinking movements of P seine and T seine generally showed linear phenomenon and the sinking speed showed gentle curve shape. Sinking tendency was distinguished by existence of flow velocity. When there is flow velocity, it showed the phenomenon that it sinking by similar type. Although sinking depth and sinking speed did not show distinguished classification, P seine shows bigger than T seine. When there was in flow velocity, the elapsed time(Et) and sinking depth (PDp, TDp) of P seine and T seine can be shown such experimental equations as PDp=(0.21V+4.96)Et-(0.62V-0.10) and TDp=(0.19V+4.95)Et-(0.72V+0.34). When there was in flow velocity, the elapsed time and siking speed (PSp, TSp) of P seine and T seine can be shown such experimental equations as $PSp=-0.11Et^2+1.42Et+1.75\;and\;TSp=-0.11Et^2+1.41Et+1.37$.

• Journal of The Geomorphological Association of Korea
• /
• v.27 no.4
• /
• pp.29-39
• /
• 2020

This study estimated influences of the Ulsan Fault on tectonic movement and uplift characteristics in the Eastern Block of the Ulsan Fault. The averaged uplift rate in the Northern Coast of the Eastern Block was 0.202 m/ka, while the site in Seokbyeong-ri, Guryongpo-eup, Pohang-si, showed relatively high rate of 0.249 m/ka, attributable to influences of small fault movement, called the Gangsa Fault. Higher averaged rate of 0.270 m/ka than in the Northern Coast was calculated in the Southern Coast of the Eastern Block. The site in north of Haseo-ri, Yangnam-myeon, Gyeongju-si, showed the highest rate, suggesting influences of the Eupcheon Fault. The Western Block of the Ulsan Fault indicated the averaged rate of 0.208 m/ka, similar to that of the Northern Coast. The sites approximately 10 km apart from the Ulsan Fault showed 1.3 times higher rate in the Eastern Block than in the Western Block, while similar rates were calculated in the sites >20 km apart from the Ulsan Fault. These distributions of the rate suggest that the Ulsan Fault has significantly influenced development of marine terrace and tectonic movement in the study area, while local fault movements have also played a role.

• Journal of the Korea Society of Computer and Information
• /
• v.8 no.3
• /
• pp.87-93
• /
• 2003

The purpose of this research is to develop a virtual reality system which enables to actually experience the virtual reality through the visual sense of human. TSS was applied in tracing the movement of moving picture in this research. By applying TSS, it was possible to calculate multiple motion vectors from moving picture, and then camera's motion parameters were obtained by utilizing the relationship between the motion vectors. For the purpose of experiencing the virtual reality by synchronizing the camera's accelerated velocity and the simulator's movements, the relationship between the value of camera's accelerated velocity and the simulator's movements was analyzed and its result was applied to the neutral network training. It has been proved that the proposed virtual reality immersion system in this dissertation can dynamically control the movements of moving picture and can also operate the simulator quite similarly to the real movements of moving picture.

• Proceedings of the IEEK Conference
• /
• 2000.06d
• /
• pp.143-146
• /
• 2000

Motion Estimation/compensation(ME/MC) is one of the efficient interframe ceding techniques for its ability to reduce the high redundancy between successive frames of an image sequence. Calculating the blocking matching takes most of the encoding time. In this paper a new fast block matching algorithm(BMA) is developed for motion estimation and for reduction of the computation time to search motion vectors. The feature of the new algorithm comes from the center-biased checking concept and the trend of pixel movements. At first, Motion Vector(MV) is searched in ${\pm}$1 of search area and then the motion estimation is exploited in the rest block. The ASP and MSE of the proposed search algorithm show good performance.

• Journal of KIISE:Software and Applications
• /
• v.29 no.1_2
• /
• pp.114-125
• /
• 2002

In this paper, we are proposing a hierarchical segmentation method that first segments the video data into units of shots by detecting cut and dissolve, and then decides types of camera operations or object movements in each shot. In our previous work[1], each picture group is divided into one of the three detailed categories, Shot(in case of scene change), Move(in case of camera operation or object movement) and Static(in case of almost no change between images), by analysing DC(Direct Current) component of I(Intra) frame. In this process, we have designed two-stage hierarchical neural network with inputs of various multiple features combined. Then, the system detects the accurate shot position, types of camera operations or object movements by searching P(Predicted), B(Bi-directional) frames of the current picture group selectively and hierarchically. Also, the statistical distributions of macro block types in P or B frames are used for the accurate detection of cut position, and another neural network with inputs of macro block types and motion vectors method can reduce the processing time by using only DC coefficients of I frames without decoding and by searching P, B frames selectively and hierarchically. The proposed method classified the picture groups in the accuracy of 93.9-100.0% and the cuts in the accuracy of 96.1-100.0% with three different together is used to detect dissolve, types of camera operations and object movements. The proposed types of video data. Also, it classified the types of camera movements or object movements in the accuracy of 90.13% and 89.28% with two different types of video data.