• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.5
• /
• pp.99-105
• /
• 2004

A shared-capacitor charge-sharing ROM (SCCS-ROM) using dummy bit lines is proposed. The SCCS-ROM reduces the bit line swing voltage using the charge-sharing technique of the conventional charge-sharing ROM (CS-ROM). Although the CS-ROM needs three small capacitors per output bit, the proposed SCCS-ROM shares the capacitors so that it needs only three capacitors. The SCCS-ROM implements the capacitors using dummy bit lines. This not only increases noise immunity but also reduces power. A SCCS-ROM with 8K${\times}$15bits implemented in a 0.35${\mu}{\textrm}{m}$ CMOS process. The SCCS-ROM consumes 8.63㎽ at 100MHz with 3.3V The simulation results show that the SCCS-ROM reduces 8.4% power compared to the CS-ROM.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.3
• /
• pp.69-80
• /
• 2015

This paper is writing about developing magnet power supply. It is very important for power supply to obtain output current in high precision and high stability. As a switching noise and a power noise are the cause of disrupting the stability of output current, to remove these at the front end, low pass filter with 300Hz cutoff frequency is designed and placed. And also to minimize switching noise of the current into magnet and to stop abrupt fluctuations, output filter should be designed, when doing this, we design it by considering load has high value inductance. As power supply demands the stability of less than 5ppm, high precision 24bit(300nV/bit) analog digital converter is needed. As resolving power of 24bit(300nV/bit) analog digital converter is high, it is also very important to design the input stage of analog digital converter. To remove input noise, 4th order low pass filter is composed. Due to the limitation of clock, to minimize quantization error between 15bit DPWM and output of ADC having 24bit resolving power, ${\Sigma}-{\Delta}$ modulation is used and bit contracted DPWM is constituted. And before implementing, to maximize efficiency, simulink is used.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.2
• /
• pp.481-487
• /
• 2013

To successfully accomplish a bit synchronization, a synchronizer should exploit a preamble pattern. A MFM (modified frequency modulation) flag is uses as a preamble in a PJM (phase jitter modulation) mode RFID standard. In the recent work, a synchronizer for a PJM mode tag was proposed, which is composed of several correlators. In this paper, we present a new bit synchronizer in which a coarse synchronization is done as in the previous work while a fine synchronization is performed via exploiting a violation bit included in the MFM flag. We show that the proposed synchronizer can significantly reduce the overall hardware complexity at the expense of slight burden to a demodulator structure. Through simulation, we also show that its performance is comparable to that of the previous system despite its hardware simplicity.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.7
• /
• pp.125-131
• /
• 1989

This paper proposes a new ABTC (Adaptive Block Truncation Coding) algorithm which improves the BTC algorithm for image data compression. A new adaptive block truncation coding which adopts a selective coding scheme depending on the local characteristics of an image has been described. The characteristics of the ABTC algorithm can be summarized as high compression ratio and the algorithm simplicity. Using this algorithm, color images can be coded at a variable bit rate from 1.0 (bit/pel) to 2.56 (bit/pel) and high compression rate (1.3-105 bit/pel) can be achieved without conspicuous image degradation compared with original images.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.11
• /
• pp.10-17
• /
• 1999

In this paper, CMOS IADC(Current-mode Analog-to-Digital Converter) which consists of only CMOS transistors is proposed. Each stages is made up 1.5-bit bit cells composed of CSH(Current-mode Sample-and-Hold) and CCMP(Current Comparator). The differential CSH which designed to eliminate CFT(Clock Feedthrough), to meet at least 9-bit resolution, is placed at the front-end of each bit cells, and each stages of bit cell ADSC (Analog-to-Digital Subconverter) is made up two latch CCMPs. With the HYUNDAI TEX>$0.65\mu\textrm{m}$ CMOS parameter, the ACAD simulation results show that the proposed IADC can be operated with 47 dB of SINAD(Signal to Noise- Plus-Distortion), 50dB(8-bit) of SNR(Signal-to-Noise) and 37.7 mW of power consumption for input signal of 100 KHz at 20 Ms/s.

• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.5
• /
• pp.310-318
• /
• 2016

Emerging technologies such as the Internet of Things (IoT) and the Advanced Driver Assistant System (ADAS) often have image transmission functions with tough constraints, like low power and/or low delay, which require that they adopt line-based, low memory compression methods instead of existing frame-based image compression standards. Bit rate control in the conventional frame-based compression systems requires a lot of hardware resources when the scope of handled data falls at the frame level. On the other hand, attempts to reduce the heavy hardware resource requirement by focusing on line-level processing yield uneven image quality through the frame. In this paper, we propose a bit rate control that maintains consistency in image quality through the frame and improves the legibility of text regions. To find the line characteristics, the proposed bit rate control tests each line for ease of compression and the existence of text. Experiments on the proposed bit rate control show peak signal-to-noise ratios (PSNRs) similar to those of conventional bit rate controls, but with the use of significantly fewer hardware resources.

• Analytical Science and Technology
• /
• v.5 no.3
• /
• pp.295-301
• /
• 1992

A versatile data acquisition and control adaptor for IBM personal computers has been developed. The data acquisition and control adaptor developed contains major components necessary for computerized data acquisition and control instrumentaions. Up to 4 differential analog signals can be acquired through a choice of dual 12-bit analog-to digital converters depending on the experimental requirements. Also, dual 12-bit digital-to-analog converters, three 16-bit programmable most computerized laboratory data acquisition and control instrumentation. The design principle and its applications are described.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.109-113
• /
• 2006

The Arithmetic Logic Unit (ALU) is a core element of a computer processor that performs arithmetic and logic operations on the operands in computer instruction words. We have developed and tested an RSFQ multi-bit ALU constructed with half adder unit cells. To reduce the complexity of the ALU, We used half adder unit cells. The unit cells were constructed of one half adder and three de switches. The timing problem in the complex circuits has been a very important issue. We have calculated the delay time of all components in the circuit by using Josephson circuit simulation tools of XIC, $WRspice^{TM}$, and Julia. To make the circuit work faster, we used a forward clocking scheme. This required a careful design of timing between clock and data pulses in ALU. The designed ALU had limited operation functions of OR, AND, XOR, and ADD. It had a pipeline structure. The fabricated 1-bit, 2-bit, and 4-bit ALU circuits were tested at a few kilo-hertz clock frequency as well as a few tens giga-hertz clock frequency, respectively. For high-speed tests, we used an eye-diagram technique. Our 4-bit ALU operated correctly at up to 5 GHz clock frequency.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.8
• /
• pp.671-677
• /
• 2016

A Controller Area Network (CAN) is a serial communication protocol that is highly reliable and efficient in many aspects, such as wiring cost and space, system flexibility, and network maintenance. Therefore, it is chosen for the communication protocol between a single chip controller based on Field Programmable Gate Array (FPGA) and peripheral devices. In this paper, the design and implementation of CAN IP, which is written in VHSIC Hardware Description Language (VHDL), is presented. The implemented CAN IP is based on the CAN 2.0A specification. The CAN IP consists of three processes: clock generator, bit timing, and bit streaming. The clock generator process generates a time quantum clock. The bit timing process does synchronization, receives bits from the Rx port, and transmits bits to the Tx port. The bit streaming process generates a bit stream, which is made from a message received from a micro controller subsystem, receives a bit stream from the bit timing process, and handles errors depending on the state of the CAN node and CAN message fields. The implemented CAN IP is synthesized and downloaded into SmartFusion FPGA. Simulations using ModelSim and chip test results show that the implemented CAN IP conforms to the CAN 2.0A specification.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.24 no.4
• /
• pp.585-592
• /
• 2014

In this paper, we study the LEA[1] block cipher system in UICC-16bit only. Also, we explain a key-schedule function and encryption/decryption structures, propose an advanced modified key-scheduling, and perform LEA in UICC-16bit that we proposed advanced modified key-scheduling. Also, we compare LEA with ARIA that proposed domestic standard block cipher, and we evaluate the efficiency on the LEA algorithm.