• Restorative Dentistry and Endodontics
• /
• v.34 no.6
• /
• pp.467-476
• /
• 2009

The aim of this study was to measure the dentinal tubular fluid flow (DFF) during and after amalgam and composite restorations. A newly designed fluid flow measurement instrument was made. A third molar cut at 3 mm apical from the CEJ was connected to the flow measuring device under a hydrostatic pressure of 15 $cmH_2O$. Class I cavity was prepared and restored with either amalgam (Copalite varnish and Bestaloy) or composite (Z-250 with ScotchBond MultiPurpose: MP, Single Bond 2: SB, Clearfil SE Bond: CE and Easy Bond: EB as bonding systems). The DFF was measured from the intact tooth state through restoration procedures to 30 minutes after restoration, and re-measured at 3 and 7days after restoration. Inward fluid flow (IF) during cavity preparation was followed by outward flow (OF) after preparation, In amalgam restoration, the OF changed to IF during amalgam filling and slight OF followed after finishing. In composite restoration, application CE and EB showed a continuous OF and air-dry increased rapidly the OF until light-curing, whereas in MP and SB, rinse and dry caused IF and OF, respectively. Application of hydrophobic bonding resin in MP and CE caused a decrease in flow rate or even slight IF. Light-curing of adhesive and composite showed an abrupt IF. There was no statistically significant difference in the reduction of DFF among the materials at 30 min. 3 and 7 days after restoration (p > 0.05).

• Resources Recycling
• /
• v.29 no.2
• /
• pp.8-17
• /
• 2020

In this study, adsorption and desorption characteristics of pulverized waste paper-mulberry pellet and bast fiber were measured to confirm the applicability to humidity control products. Paper-mulberry powder was classified by 710-355㎛, 355-100㎛, 100-45㎛ and less than 45㎛ and used in experiment. Specific surface area increased from 1.02㎡/g to 1.35㎡/g as the particle size decreased from 710㎛ to under 45㎛. Adsorption and desorption performance decreased in the order of 355-100㎛, 710-355㎛, 100-45㎛, less than 45㎛ and bast fiber, adsorption content on each particle sizes were 141.1g/㎡, 147.1g/㎡, 135.7g/㎡, 129.0g/㎡ and desorption content were 117.2g/㎡, 123.6g/㎡, 110.2g/㎡, 93.3g/㎡. As a result, adsorption and desorption performance of paper-mulberry powder were superior to those of the bast fiber and these phenomenon can be considered that it caused by pore distribution in pellet and damage of fiber.

• Journal of Embryo Transfer
• /
• v.28 no.4
• /
• pp.373-379
• /
• 2013

Spermatogonial stem cells (SSCs) developed into sperms through spermatogenesis have been utilized as a useful tool in the field of regenerative medicine and infertility. However, a small number of highly qualified SSCs are resided in the seminiferous tubule of testis, resulted in developing effective in-vitro culture system of SSCs for solving simultaneously quantitative and qualitative problems. Presently, SSCs can be enriched on testicular stromal cells (TSCs), but there are no systematic researches about TSC culture. Therefore, we tried to optimize culture condition of TSCs derived from mouse with different strains. For these, proliferation and viability were measured and compared by culturing ICR outbred or DBA/2 inbred mouse-derived TSCs at 35 or $37^{\circ}C$. In case of ICR strain, primary TSCs cultured at $37^{\circ}C$ showed significantly higher proliferation and viability than those at $35^{\circ}C$ and significant increase of proliferation and viability in sub-passaged TSCs was detected in the $35^{\circ}C$ culture condition. Moreover, sub-passage of primary TSCs at $35^{\circ}C$ induced no significant effects on proliferation and viability. In contrast, in case of DBA/2 strain, significantly improved proliferation were detected in the primary TSCs cultured at $35^{\circ}C$, which showed no significant difference in the viability, compared to those at $37^{\circ}C$. Furthermore, sub-passaged TSCs cultured at $37^{\circ}C$ showed no significant differences in proliferation and viability, compared to those at $35^{\circ}C$. However, with significant decrease of proliferation induced by sub-passage of primary TSCs at $35^{\circ}C$, no significant effects on proliferation and viability were resulted from sub-passage of primary TSCs at $37^{\circ}C$. From these results, culture temperature of primary TSCs derived from outbred and inbred strain of mouse could be separately optimized in primary culture and subculture.

• Microbiology and Biotechnology Letters
• /
• v.42 no.2
• /
• pp.190-193
• /
• 2014

CMP-Neu5Ac synthetase is a key enzyme for the synthesis of CMP-Neu5Ac, which is an essential precursor of sialylated glycoconjugates. For the soluble expression of the CMP-Neu5Ac synthetase gene (neuA) from Escherichia coli K1, various heat shock proteins were co-expressed in E. coli BL21 (DE3) Star. In order to do this, a pG-KJE8 plasmid, encoding genes for GroEL-ES and DnaK-DnaJ-GrpE, was co-transformed with neuA and was expressed at $20^{\circ}C$ by the addition of 0.01 mM IPTG and 0.005 mg/ml L-arabinose. The co-expression of a variety of heat shock proteins resulted in the remarkably improved production of soluble CMP-Neu5Ac synthetase in E. coli.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.51-56
• /
• 2017

Nitinol, a shape memory alloy (SMA), is manufactured from titanium and nickel and it used in various fields such as electrical applications, micro sensors. It is also recommended as a material in medical for implant because it has excellent organic compatibility. Nitinol is intended to be inserted into the human body, products require a high-quality surface and low residual stress. To overcome this problems, explore electrolyte polishing (EP) is being explored that may be appropriate for use with nitinol. EP is a particularly useful machining method because, as a non contact machining method, it produces neither machining heat nor internal stress in the machined materials. Sandpaper polishing is also useful machining method because, as a contact machining method, it can easily good surface roughness in the machined materials. The electrolyte polishing (EP) process has an effect of improving the surface roughness as well as the film polishing process, but has a characteristic that the residual stress is hardly generated because the work hardened layer is not formed on the processed surface. The sandpaper polishing process has the effect of improving the surface roughness but the residual stress remains in the surface. We experimented with three conditions of polishing process. First condition is the conventional polishing. Second condition is the electrochemical polishing(EP). And Last condition is a mixing process with the conventional polishing and the EP. Surface roughness and residual stress of the nitinol before a polishing process were $0.474{\mu}mRa$, -45.38MPa. Surface roughness and residual stress of the nitinol after mixing process of the conventional polishing and the EP were $1.071{\mu}mRa$, -143.157MPa. Surface roughness and residual stress of the nitinol after conventional polishing were $0.385{\mu}mRa$ and -205.15MPa. Surface roughness and residual stress of sandpaper and EP nitinol were $1.071{\mu}mRa$, -143.157MPa. The result shows that the EP process is a residual stress free process that eliminates the residual stress on the surface while eliminating the deformed layer remaining on the surface through composite surface machining rather than single surface machining. The EP process can be used for biomaterials such as nitinol and be applied to polishing of wafers and various fields.

• Restorative Dentistry and Endodontics
• /
• v.34 no.2
• /
• pp.120-129
• /
• 2009

The purpose of this study was to investigate the pulpal response to direct pulp capping with dentin sialoprotein (DSP) -derived synthetic peptide in teeth of dogs, and to compare its efficacy to capping substances $Ca(OH)_2$ and white mineral trioxide aggregate (WMTA). A total of 72 teeth of 6 healthy male beagle dogs were used. The mechanically exposed pulps were capped with one of the following: (1) DSP-derived synthetic peptide (PEP group): (2) $Ca(OH)_2$ (CH group): (3) a mixture paste of peptide and $Ca(OH)_2$ (PEP+CH group): or (4) white MTA (WMTA group). The access cavity was restored with a reinforced glass ionomer cement. Two dogs were sacrificed at each pre-determined intervals (2 weeks, 1 month, and 3 months). After the specimens were prepared for standard histological processing, sections were stained with hematoxylin and eosin. Under a light microscope, inflammatory response and hard tissue formation were evaluated in a blind manner by 2 observers. In the PEP group, only 3 of 17 specimens showed hard tissue formation, indication that the DSP-derived synthetic peptide did not induce proper healing of the pulp. Compared with the CH group, the PEP group demonstrated an increased inflammatory response and poor hard tissue formation. The CH and WMTA groups showed similar results for direct pulp capping in mechanically exposed teeth of dogs.

• Polymer(Korea)
• /
• v.28 no.3
• /
• pp.211-217
• /
• 2004

The sol to gel transition of aqueous solution of block copolymers consisting of methoxy poly (ethylene glycol) (MPEG) and biodegradable polyesters such as $\varepsilon$-caprolactone and L-lactide was investigated as a function of temperature. MPEG-PCL was prepared by ring opening polymerization of $\varepsilon$-caprolactone in the presence of HClㆍEt$_2$O as monomer activator at room temperature. Also, MPEG-PLLA was prepared by ring opening polymerization of L-lactide in the presence of stannous octoate at 115$^{\circ}C$. The properties of block copolymers were investigated by $^1$H-NMR, IR, and GPC as well as the observation of thermo sensitive phase transition in aqueous solution. As the hydrophobic block length increased, the sol to gel transition temperature increased and curve of that steepen to lower concentration. To confirm the gel formation at body temperature, we observed the formation of gel in the mice body after injection of 20 wt% aqueous solution of each block copolymer. After surging, we investigated the gelation in mice. The results obtained in this study confirmed the feasibility as biomaterials of injectable implantation for controlled release of drug and protein delivery.

• Polymer(Korea)
• /
• v.35 no.3
• /
• pp.189-195
• /
• 2011

The design of new bioactive scaffolds offering physiologic environment for tissue formation is an important frontier in biomaterials research. In this study, we performed compressive strength, water-uptake ability, and SEM analysis for physical property assessment of 3-D silk/PLGA scaffold, and investigated the adhesion, proliferation, phenotype maintenance, and inflammatory responses of RAW 264.7 and NIH/3T3 for cell compatibility. Scaffolds were prepared by the solvent casting/salt leaching method and their compressive strength and water-uptake ability were excellent at 20 wt% silk content. Result of cell compatibility assay showed that inflammatory responses distinctly decreased, and initial adhesion and proliferation were maximized at 20 wt% silk content. In conclusion, we suggest that silk/PLGA scaffolds may be useful to tissue engineering applications.

• Macromolecular Research
• /
• v.17 no.8
• /
• pp.616-622
• /
• 2009

In-depth understanding of the influence of hot pressing and melt processing on the properties of thermoplastic polyurethane (TPU) is critical for effective mechanical recycling of TPU scraps. Therefore, this study focused on the effects of hot pressing and melt mixing on molecular weight (MW), polydispersity index (PDI), melt index (MI), characteristic IR peaks, hardness, thermal degradation and mechanical properties of TPU. The original TPU pellet (o-TPU) showed two broad peaks at lower and higher MW regions. However, four TPU film samples, TPU-0 prepared only by hot pressing of o-TPU pellet and TPU-1, TPU-2 and TPU-3 obtained by hot pressing of melt mixed TPUs (where the numbers indicate the run number of melt mixing), exhibited only a single peak at higher MW region. The TPU-0 film sample had the highest $M_n$ and the lowest PDI and hardness. The TPU-1 film sample had the highest $M_w$ and tensile modulus. As the run number of melt mixing increased, the peak-intensity of hydrogen bonded C=O stretching increased, however, the free C=O peak intensity, tensile strength/elongation at break and average MW decreased. All the samples showed two stage degradations. The degradation temperatures of TPU-0 sample (359 $^{\circ}C$ and 394 $^{\circ}C$)were higher than those of o-TPU (342 $^{\circ}C$ and 391 $^{\circ}C$). While all the melt mixed samples degraded at almost the same temperature (365 $^{\circ}C$ and 381 $^{\circ}C$). The first round of hot pressing and melt mixing was found to be the critical condition which led to the significant changes of $M_n$/$M_w$/PDI, MI, mechanical property and thermal degradation of TPU.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.2
• /
• pp.238-247
• /
• 2015

Katsura tree (Cercidiphyllum japonicum Sieb. Et Zucc) leaves were collected, air-dried and extracted with 70% aqueous acetone, then concentrated and sequentially fractionated using n-hexane, $CH_2Cl_2$, EtOAc, and $H_2O$ to be freeze dried for antioxidant and ${\alpha}$-glucosidase inhibition activity tests. The antioxidant activity of the extracts was evaluated using DPPH (1,1-diphenyl 2-picrylhydrazyl) free radical scavenging assay. The test concentrations were adjusted to 500, 250, 125, 62.5, 31.25, 15.62, 7.81, 3.9, 1.95 and 0.97 ppm. The $H_2O$ and EtOAc fractions showed higher activities compared with the control, ${\alpha}$-tocopherol, at all concentrations. The crude fraction also gave better activity at the concentrations lower than 62.5 ppm. However, the nonpolar n-hexane and $CH_2Cl_2$ fractions gave prominently lower activities compared with the control at all concentrations. The $IC_{50}$ values of the crude, EtOAc, and $H_2O$ fractions exhibited 11.78, 4.29 and $9.80{\mu}g/m{\ell}$, respectively, compared with $12.08{\mu}g/m{\ell}$ of the control. But the n-hexane and $CH_2Cl_2$ fractions indicated 300 and $91.85{\mu}g/m{\ell}$ of $IC_{50}$, respectively. ${\alpha}$-Glucosidase inhibition activity was evaluated at the concentrations of 50, 25, 12.5, 6.3, 3.1, 1.6 and 0.8 ppm. The inhibition activities were increased according to as the increase of sample concentrations. However, the nonpolar n-hexane and $CH_2Cl_2$ fractions indicated very low inhibition activities compared with acarbose, a positive control. The EtOAc fraction showed very good capability as almost 100% compared with the control at the higher concentrations than 12.5 ppm and the crude fraction also indicated good potential as 95% and 100% at 25 and 50 ppm, respectively. The $H_2O$ fraction gave good inhibition value as 90% at 50 ppm although the value was lower than the control. These results showed that the polar fractions had better ${\alpha}$-glucosidase inhibition activities. The $IC_{50}$ values of the nonpolar fractions, n-hexane and $CH_2Cl_2$, showed very lower values as 468 and $103.6{\mu}g/m{\ell}$, respectively, than the control. ${\alpha}$-Glucosidase Inhibition Activity of the Extracts of Katsura Tree (Cercidiphyllum japonicum Sieb. Et Zucc) Leaves However, the polar fractions, crude, EtOAc and $H_2O$, showed 7.1, 3.7 and $13{\mu}g/m{\ell}$, respectively, indicating that these fractions can be used as natural bioresources for treating diabetes mellitus. Also ${\alpha}$-glucosidase inhibition activity had a positive correlation with antioxidant activity of the extracts.