• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.590-595
• /
• 2006

This paper presents the friction and anti-wear characteristics of nano-oil with a mixture of a refrigerant oil and carbon nano-particles in the thrust slide-bearing of scroll compressors. Frictional loss in the thrust slide-bearing occupies a large part of total mechanical loss in scroll compressors. The characteristics of friction and anti-wear using nano-oil are evaluated using the thrust bearing tester for measuring friction surface temperature and the coefficient of friction at the thrust slide-bearing as a function of normal loads up to 4,000 N and orbiting speed up to 3,200 rpm. It is found that the coefficient of friction increases with decreasing orbiting speed and normal force. The friction coefficient of carbon nano-oil is 0.015, while that of pure oil is 0.023 under the conditions of refrigerant gas R-22 at the pressure of 5 bars. It is believed that carbon nano-particles can be coated on the friction surfaces and the interaction of nano-particles between surfaces can be improved the lubrication in the friction surfaces. Carbon nano-oil enhances the characteristics of the anti-wear and friction at the thrust slide-bearing of scroll compressors.

• Tribology and Lubricants
• /
• 제38권5호
• /
• pp.205-212
• /
• 2022

This paper presents experimental measurements of the structural characteristics of a two-pad beam-type gas foil journal bearing and its rotordynamic performance for a high-speed motor-driven turbocompressor. The test bearing had two top foils and two beam foils, each with an arc length of ~180°. Each beam foil was etched to obtain 40 beams with six geometries of different lengths and widths. The insertion of beam foils into the bearing housing produces equivalent beam heights. The structural tests of the bearing with a non-rotating journal revealed a smaller bearing clearance and larger structural stiffness for the load-on-pad configuration than for the load-between-pads configuration. Rotordynamic performance measurements during driving tests up to 100 krpm demonstrated synchronous vibrations and subsynchronous vibrations with large amplitudes. The test was repeated after inserting the shim between the top foil and beam foil to reduce the bearing radial clearance. The reduced bearing clearance resulted in a reduction in the peak amplitude of the synchronous vibrations and an increase in the speed at which the peak amplitude occurred. In addition, the onset speed and amplitude of the subsynchronous vibrations were dramatically increased and diminished, respectively. The rotor coast-down tests at 100 krpm show that the reduction in the bearing clearance extends the time to rotor stop, thus implying an improvement in hydrodynamic pressure generation and a reduction in bearing frictional torque.

• 대한조선학회논문집
• /
• 제43권4호
• /
• pp.512-520
• /
• 2006

The effects of flexibilities of supporting structures on shaft alignment are growing as ship sizes are Increasing mainly for container carrier and LNG carrier. But, most of classification societies not only do not suggest any quantitative guidelines about the flexibilities but also do not have shaft alignment design program considering the flexibility of supporting structures. A newly developed program, which is based on innovative shaft alignment technologies including nonlinear elastic multi-support bearing concept and hull deflection database approach, has S basic modules : 1)fully automated finite element generation module, 2) hull deflection database and it's mapping module on bearings, 3) squeezing and oil film pressure calculation module, 4) optimization module and 5) gap & sag calculation module. First module can generate finite element model including shafts, bearings, bearing seats, hull and engine housing without any misalignment of nodes. Hull deflection database module has built-in absolute deflection data for various ship types, sizes and loading conditions and imposes the transformed relative deflection data on shafting system. The squeezing of lining material and oil film pressures, which are relatively solved by Hertz contact theory and built-in hydrodynamic engine, can be calculated and visualized by pressure calculation module. One of the most representative capabilities is an optimization module based on both DOE and Hooke-Jeeves algorithm.

• 대한통합의학회지
• /
• 제9권1호
• /
• pp.41-48
• /
• 2021

Purpose : The purpose of this study is to find out if it helps to improve static balance ability and weight bearing rate for chronic stroke patients with poor balance in clinical intervention through a method of correcting movement errors while performing a task by vibrotactile bio-feedback providing pressure information. Methods : Fifteen chronic stroke patients (12 male and 3 female) were participated in this study. To examine the effects of vibrotactile bio-feedback and general standing without bio-feedback on static balance ability and weight distribution symmetric index in all subjects randomized with R Studio. The static balance ability and weight distribution symmetric index of the participants was evaluated using a force plate. A paired t-test was used for comparison of each conditions. Statistical significance was set at α=0.05. Results : The comparisons of static balance ability and weight distribution symmetric index in chronic stroke patients after two different condition are as follows. In the static balance ability and weight distribution symmetric index, the vibrotactile feedback providing pressure information showed a significant difference compared to none feedback (p<.001). Conclusion : The vibrotactile bio-feedback providing pressure information in real time can support an improve in static balance ability, uniform weight bearing rehabilitation in chronic stroke patients. In the future, it is hoped that a follow-up study that provides a better direction of intervention compared to various feedback interventions commonly used in clinical practice.

• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.168-192
• /
• 2020

In recently designed diesel engines, the running conditions for piston-pin bearings have become severe because of the higher combustion pressure and increased temperature. Moreover, the metal removal from the bushing material has strongly reduced the ability of the antifriction material to accept asperity contacts. Therefore, it is necessary to find ways of reducing wear scar on the connecting-rod small-end bushing and piston-pin boss bearing related to the higher combustion pressure on the power cell of an engine. In this work, the position and level of material removal from the surfaces of the bushing and bearing under such severe operating conditions - for example, maximum power and torque conditions of a passenger car diesel engine - are estimated for several combinations of surface roughness. First, piston-pin rotating motion is investigated by calculating the friction coefficient at piston-pin bearings, the oil film thickness, and the frictional torques induced by hydrodynamic shear stress. Subsequently, the wear scarring on the surfaces of a connecting-rod small-end bushing and two piston-pin boss bearings related to piston-pin rotational motion is numerically calculated under the maximum power and torque operating conditions. This work is helpful to determine the reasonable surface roughness of the bushing and bearing for reducing wear volume occurring at the interface between a bearing and a shaft.

• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.13-18
• /
• 2013

Slider bearing is a widely used load-carrying element in the industry. While a large number of studies have investigated the effect of overall surface curvature, very few have considered sinusoidal surface. Recently, consideration of surface roughness/waviness or intentional wave design has been identified as an important issue in the manufacture of hard disk driver, mechanical seal, hydraulic machine, and etc. This study investigated the load-carrying capacity of a finite-width slider bearing with a wavy surface. Film thickness ratios, length-width ratio, ambient pressure, amplitude, and partial distribution were selected as the simulation parameters. The calculation results showed that the load-carrying capacity rapidly varied at small film thickness ratio, but the waviness near the area of minimum film thickness made much more influence with an increase in film thickness ratio. As the length-width ratio of bearing was increased, ambient pressure became more influential at small film thickness ratios. Furthermore a particular partial distribution of the wavy area led to higher load-carrying capacity than did the whole distribution. Consequently, the results of this study are expected to be of use in surface micro-machining of finite-width slider bearings.

• 한국지반환경공학회 논문집
• /
• 제2권2호
• /
• pp.13-22
• /
• 2001

본 연구에서는 제지회를 성토재로 활용할 경우 제지회의 지지력 특성을 파악하기 위하여 원심모형실험을 실시하였다. 모형실험은 기초폭과 중력수준을 변화시켜 실시하였으며, 하중재하에 따른 침하와 수직토압을 측정하였다. 모형실험결과는 지지력 이론 및 유한차분 해석프로그램인 FLAC을 이용한 수치해석 결과와 비교 분석하였다. 실험결과, 하중-침하특성은 침하비 s/B가 약 25~30%에서 변곡점을 나타내는 국부전단파괴 양상을 보이며, g-level과 기초폭이 증가할수록 하중강도가 증가하고 있다. 실험에서 측정된 극한지지력은 Terzaghi 이론에 의한 결과와 유사한 것으로 나타났다. 기초 중심에서 이격거리가 증가할수록 수직토압이 크게 감소하였으며, E/B가 7이상에서는 하중재하에 따른 응력증가가 거의 발생하지 않았다. 하중재하에 의한 수직변위는 기초 직하부에서 가장 크며, 깊이 4cm 이상, 이격거리 E/B=5.0 이상에서는 거의 발생하지 않는 것으로 나타났다.

• Tribology and Lubricants
• /
• 제40권1호
• /
• pp.17-23
• /
• 2024

This study analyzes the thermal effects on the performance of an air foil thrust bearing (AFTB) using COMSOL Multiphysics to approximate actual bearing behavior under real conditions. An AFTB is a sliding-thrust bearing that uses air as a lubricant to support the axial load. The AFTB consists of top and bump foils and supports the rotating disk through the hydrodynamic pressure generated by the wedge effect from the inclined surface of the top foil and the elastic deformation of the bump foils, similar to a spring. The use of air as a lubricant has some advantages such as low friction loss and less heat generation, enabling air bearings to be widely used in high-speed rotating systems. However, even in AFTB, the effects of energy loss due to viscosity at high speeds, interface frictional heat, and thermal deformation of the foil caused by temperature increase cannot be ignored. Foil deformation derived from the thermal effect influences the minimum decay in film thickness and enhances the film pressure. For these reasons, performance analyses of isothermal AFTBs have shown few discrepancies with real bearing behavior. To account for this phenomenon, a thermal-fluid-structure analysis is conducted to describe the combined mechanics. Results show that the load capacity under the thermal effect is slightly higher than that obtained from isothermal analysis. In addition, the push and pull effects on the top foil and bump foil-free edges can be simulated. The differences between the isothermal and thermal behaviors are discussed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 기초기술위원회 워크샵
• /
• pp.1-26
• /
• 2002

This study addresses preliminary design and construction specification for micropiles. Especially several design methods for micropiles in sands, clays or mixed soil layers are described. The bearing capacity of micropiles are mainly depended upon the shaft resistance. Therefore, the pressure of grouting is one of the most important design parameters for the bearing capacity evaluation of micropile. There is no theoretical way to evaluate the shaft resistance of micropile up to now because grouting method is another key parameter for micropile design approach. Because of above reasons, the present design approaches of the micropile are based on the collected field data The bearing capacities of designed micropiles should be verified by static load tests before and after construction at the planned site.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.93-98
• /
• 2000

Turbulence on the journal bearing operation is examined. And the thermal variability is studied for isothermal, convective and adiabatic conditions on the walls within some degree of journal misalignment. An efficient algorithm for the solution of the coupled turbulent Reynolds and energy equations is used to examine the effects of the various factors. The calculation data of turbulent analysis are compared with the ones of laminar analysis. Heat convection is found to play but a small role in determining friction and load. The friction distribution patterns through inside a journal bearing now appear different with high values at the front part of the bearing due to the high speed and low temperature, and a sudden decrease past the pressure maximum.