• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.167-168
• /
• 2006

This paper is concerned about the development system that the bead width's size can be controlled. In order to control the bead width, DC motor driving slide on auto carriage is used. The adjustment of bead width is carried by amplitude and weaving shape is controlled by MCU(Micro Controller Unit). We confirmed the result by tracking experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.1
• /
• pp.201-210
• /
• 1994

A theoretical heat-flow model incorporating with a constant moving CO$_{2}$ laser beam has been analyzed to predict depth and the shape of bead section during last beam welding. The laser beam is exponentially attenuated with an abosrption coefficient in the material. The solution can be expressed in terms of normalized variables. The experimental data were generated by usint CW 2 CO$_{2}$ laser with multi beam mode and CW 3 kW CO$_{2}$laser with Gaussian mode. The specimens were made as bead-on-plate welds for SM 10C, STS 304, STS 316, STS 420 and pure Nickel. The maximum possible penetration depth and the shape of beas section for given sources of laser power, travel speed and beam spot size can be prdicted with this model in a given material.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.6
• /
• pp.615-621
• /
• 2015

In this paper diamond wire cutting method has been proposed to cut the rock in the tunnel face. Diamond wire saw method could cut the rock from tunnel face with very minor vibration and noise. In this study rock cutting process has been simulated with FEM method by using LS-DYNA explicit non-linear finite element code. Normal load act as an prime factor when cutting the rock surface. For observing the effect of normal load on bead, several experiments has been conducted by varying normal loads on the bead. From each experiment, cutting rate has been calculated to compare the cutting rate with different load conditions. By increasing the normal load on bead, cutting rate increases drastically.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.315-318
• /
• 2001

We are proposing a new mobile phone antenna, which has a specially manufactured Mn-Zn cylindrical ferrite bead inside of the helical coil of the antenna. The extended antenna radiation patters and the spatial peak SAR averaged over 1 gram simulated tissue with and without the ferrite bead insertion were measured at 824 MHz. The results show that the ferrite bead resulted in SAR reduction about 20 %, and reflection coefficient increase about 7 % for the extended antenna. The applicability of this scheme to the antenna mass production is quite feasible.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1690-1691
• /
• 2008

Micro cell stimulation device is interested in many researchers because it has several advantages such as saving time and reagents. We introduce new micro-bioreactor using micro bead and conduct cell stimulation experiments to verify effective time because cell have operated by cell-cycle (G1, S, G2, and M phase). Micro-bioreactor was made by soft lithography and CAPE (calf pulmonary artery endothelial cell) was cultured in PDMS (polydimethylsiloxane) micro device for 12 hour and cell starvation process was performed for 24 hours. Micro glass beads were rolled only by slating device every hour during 15 hour because of minimizing other stimulation force like flow and pressure. The result represents that cells under exposed under micro bead stimulation show higher growth rate than normal condition and earlier and later stimulation time are more effective.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2005.04a
• /
• pp.171-174
• /
• 2005

Suspected carcinogen, TCE and PCE, are the most common groundwater pollutants extensively used as a solvent and degreaser. In this study, oxygenases were immobilized in Ca-alginate and chitosan bead. TCE degradation by the immoblized enzyme beads were measured for various size, enzyme addition volume and TCE contact time. The degradation was decreased as increasing the bead size. For overnight , more than 20% of TCE was degraded. The variation of enzyme activity was tested for the repeated use of enzyme beads.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.16 no.3
• /
• pp.25-33
• /
• 1979

The relation between the welding conditions and welding distortions were studied with the weld parameters, current, welding speed and plate thickness, and the form of the distortions were derived theoretically. To derive these formulas, the temperature distribution on the plane normal to the direction of the weld line was assumed to be parabolic. Both the theoretical studies for the transverse shrinkage and angular distoction were compared with the experiments. The experiments were performed on the fundamental cases of a bead welds on rectangular mild steel plates. It was found that the distoction formulas were in good agreement with the results of the experiments. The formulas for the calculation of the distortion were established for the case of bead on plate weld using rectangular mild steel plate and the KS E4313, $4mm\phi$ welding rod.

• Journal of Welding and Joining
• /
• v.18 no.5
• /
• pp.63-69
• /
• 2000

A genetic algorithm was applied to an arc welding process to determine near optimal settings of welding process parameters which produce good weld quality. This method searches for optimal settings of welding parameters through systematic experiments without a model between input and output variables. It has an advantage of being able to find optimal conditions with a fewer number of experiments than conventional full factorial design. A genetic algorithm was applied to optimization of weld bead geometry. In the optimization problem, the input variables was wire feed rate, welding voltage, and welding speed and the output variables were bead height, bead width, and penetration. The number of level for each input variable is 16, 16, and 8, respectively. Therefore, according to the conventional full factorial design, in order to find the optimal welding conditions, 2048 experiments must be performed. The genetic algorithm, however, found the near optimal welding conditions from less than 40 experiments.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.2
• /
• pp.26-32
• /
• 2012

In this paper, the effects of irregular bead shapes on fatigue life were investigated. A modified S-N curve method was used to estimate the fatigue life, which considered the inherent multiaxiality caused by the geometrical feature produced by the welding process. The point method of the critical distance method was used to determine the fatigue effective stress. Three types of fillet joint models were tested in the fatigue experiments. For each model, real bead shapes were collected using a 3D laser scanner, and finite element analyses were performed. The results of the analyses with actual bead shapes were compared with those using an idealized bead shape model. The results of the present analytical methods showed good agreement with the experimental results.

• Journal of Welding and Joining
• /
• v.17 no.2
• /
• pp.53-60
• /
• 1999

Conventionally, CCD camera and vision sensor using the projected pattern of light is generally used to inspect the weld bead defects. But with this method, a lot of time is needed for image preprocessing, stripe extraction and thinning, etc. In this study, laser vision sensor using the scanning beam of light is used to shorten the time required for image preprocessing. The software for deciding whether the weld bead is in proper shape or not in real time is developed. The criteria are based upon the classification of imperfections in metallic fusion welds(ISO 6520) and limits for imperfections(ISO 5817).