Additives, such as sodium perborate and borax, were examined in dialdehyde wrinkle resistant finishing of cotton. Results indicated that the whiteness index(WI) of cotton treated with dialdehyde and additive showed about 90% of WI of the untreated cotton but with decrease in wrinkle recovery angle (WRA) due to inhibition effect of these additives. Effect of additive on the WRA reduction was more prominent with glutaraldehyde than with glyoxal. Reduction in WRA of cotton treated with both dialdehydes and boron compound was minimized by simultaneous addition of formic acid in the bath. Addition of formic acid was also generally beneficial in maintaining WI retentions after 8 months storage. Furthermore, boron compounds were also effective in improving retentions of mechanical properties. By FTIR analysis the residual aldehyde group was detected on the dialdehyde-finished cotton, whereas no peak was shown by addition of boron compounds. This suggested that the residual aldehyde group was a main cause of fabric yellowing on the dialdehyde-finished cotton. Dialhehyde with boron compound, therefore, can be used to replace a conventional formaldehyde-containing wrinkle resistant finishing of cotton.
Proceedings of the Korean Institute of Surface Engineering Conference
/
2009.05a
/
pp.153-153
/
2009
첨가제를 사용한 피로인산구리 도금욕에서 마그네슘 합금상에 직접 구리도금을 실시하였다. 피로인산구리 도금욕에서 첨가제가 마그네슘 합금 도재에 미치는 영향에 대하여 연구하였다. 연구에 따른 첨가제를 포함하는 피로인산구리 도금욕에서 구리도금층의 적합성을 확인하기 위하여 기존의 마그네슘 모재에 구리를 도금하기 위한 방법인 징케이트 처리 후 시안구리도금욕에서 구리도금하는 방법과 비교 고찰 하였다.
Journal of the Korean institute of surface engineering
/
v.32
no.3
/
pp.214-218
/
1999
The effect of additives in nickel and copper electroplating were investigated for MEMS applications. Saccharin and gelatin were used as additives in nickel and copper electroplating bath respectively. The morphology and surface hardness of electroplated coating were investigated with additive concentration. Microstructures were fabricated with optimum conditions.
Proceedings of the Membrane Society of Korea Conference
/
2003.07a
/
pp.107-114
/
2003
This study investigated the effect of 2-methoxy ethanol (2-Me) non-solvent as additive included in casting solution. Macroporous polymer membranes were prepared by using polyethersufone (PES)/N-methyl-2-pyrrolidone (NMP)/2-Me casting solution and water coagulant. The phase separation co-process of the vapor-induced phase separation (VIPS) and liquid-induced phase separation (LIPS) were used by means of membrane preparation method. The pore size and pore size distribution were controlled with additive (non-solvent), and measured with Automated Perm Porometer. By increasing additive (non-solvent) in the casting solution, the membranes produced changed from finger structure to sponge structure. That is due to the different diffusion rates. At slow diffusion process, sponge-like structure was formed and at fast diffusion process, finger-like structure was formed. Also relative humidity, evaporation time, temperature of casting solution and coagulation bath etc. had effects on the pore size distribution and the porosity of the membrane.
Journal of the Korean institute of surface engineering
/
v.17
no.4
/
pp.106-119
/
1984
Brass was electrodeposited over the range of the current densities from 2 to 8 A/$dm^2$ in cyanide bath at 20 and 40$^{\circ}C$. The cathode overpotential increased and the cathode efficiency was decreased respectively with decreasing temperature, increasing current density and addition of organic substance. The perferred orientation of the deposits were associated with the cathode overpotential and the nucleation energy of lattice planes. The (111) preferred orientation developed at the low current density and low cathode overpotential (440-520mV). On the other hand, the (111)+(100) preferred orientation developed at higher cathode overpotential (528-680mV). The (111)+(100) preferred orientation developed over the whole range of overpotential in the cyanide solution with organic additive. The copper content of deposit decreased with increasing current density and decreasing temperature. The morphology of the deposits with no additive was the polygonal body type of structure and the structure of the cross section was columnar structure. The morphology of the deposits with additive, on the other hand, was fine crystallite type of structure. And the structure of the cross section of them was the finer granular structure.
Journal of the Korean Crystal Growth and Crystal Technology
/
v.7
no.3
/
pp.456-464
/
1997
The effect of the additives on the Zn-Ni alloy electrocrystallization from a chloride bath was investigated by means of electrochemical methodes, scanning electron microscopy and measurement of surface appearance, X-ray diffraction patterns. The additives tested were the surfactant of naphtalene-derivative, saccharin and aliphatic alcohol. The resistance of electrodeposit increased by adding the additives, whereas the effect of additives on resistance was different with current density. The nickel content of alloy deposit was increased by the addition of alcohol, while decreased by the surfactant. The surface roughness, appearance and morphology of deposit were also influenced by the type of additive. The fine, compact grains and good surface roughness could be obtained from the surfactant or alcohol -added bath, and the surfactant or saccharin improved the surface appearance.
In this study, we prepared PVDF membranes via TIPS for water treatment applications. PVDF was used for its excellent chemical and mechanical properties. The effect of coagulation bath composition, temperature, and heat capacity on the overall membrane morphology was studied and observed using SEM. A mixture of DOP and DBP was used as the diluent, and silica was used as an additive. It was observed that as the heat capacity of the coagulation bath increased, the crystallization rate of PVDF decreased yielding larger pores. Also, as the heat capacity of the coagulation bath decreased, the crystallization rate of PVDF increased yielding smaller pores.
Park, Keun Yung;Uhm, Young Rang;Choi, Sun Ju;Park, Deok-Yong
Journal of the Korean Magnetics Society
/
v.23
no.1
/
pp.12-17
/
2013
Nanocrystalline nickel (Ni) tick films were synthesized by direct current electrodeposition at current density from 1 to $30mA/cm^2$ and pH = 4. The basic composition of the bath, which was prepared by dissolving Ni metal particles in HCl, was 0.2M Ni ions. The effects of the current density on the average grain size of Ni deposits were investigated by XRD and SEM techniques. The results showed that the surface roughness was decreased as the saccharin addition was increased up to 2 g/l. The experimental results showed that the increase in the current density had a considerable effect on the average grain size of the Ni deposits. The perpendicular magnetization was raised as the thickness of coating layer was increased.
Journal of the Korean institute of surface engineering
/
v.42
no.5
/
pp.191-196
/
2009
Nanocrystalline Cu thin films were electrodeposited from sulfate baths and investigated systematically the influences of $Cu^{2+}$ concentration and additives on current efficiency, residual stress, surface morphology, and XRD patterns of electrodeposited Cu film. Current efficiency was nearly 100% at from 0.2M to 1.0 M $Cu^{2+}$ concentration. but it was linearly increased with $Cu^{2+}$ concentration at less than 0.2M. The residual stress was observed in range of 7.9 to 18.4 MPa and tensile stress mode. Dendritic and powdered form was obtained at below 0.1 M. As increased with $Cu^{2+}$ concentration in solution, the main peak in the XRD pattern shifted (111) and (220) from (200). In the other hand, all about 100% current efficiency observed in all additive concentration systems, and residual stress observed in range of 20.4 to 26.3 MPa tensile stress. The condition 5(Ultra make-up - 10 ml/l, Ulta A - 0.5ml/l, Ultr B - 0.5 ml/l) was good surface morphology, and fcc(111) peak in XRD patterns increased with increasing additive concentration.
Journal of the Korean institute of surface engineering
/
v.37
no.2
/
pp.99-109
/
2004
The effect of trace metallic additives on microstructure, glossiness and hardness of Zinc electrodeposits was investigated by using sulfate bath and flow cell system. The preferred orientation of Zn deposits with Mg-Fe additives was (10$\ell$)+(002) mixed texture, while that of Zn deposits with Mg-Fe-Cr additives was ( $10\ell$). The preferred orientation of Zn deposits with Mg-Fe-X(X:Ni,Co) additives changed from ($10\ell$)+(002) to ($10\ell$) with increasing Mg additive from 5 to 10 g/$\ell$. The surface morphology of the Zinc deposits was closely related to the preferred orientation of the deposits. The glossiness of Zn deposits with Mg-Fe additives was similar to that of pure Zn deposit. The glossiness of Zn deposits with Mg-Fe-X(X:Ni,Cr) additives was lower than that of Zn deposits with Mg-Fe additives, while that of Zn deposits with Mg-Fe-Co additives was higher than that of Zn-Mg-Fe deposits. The hardness of Zn deposits with Mg-Fe-X(Ni,Co,Cr) increased with current density and amount of Mg additive. Hardness of Zn deposits was decreased and increased in comparison with Zn-Mg-Fe deposits for Mg-Fe-Co and Mg-Fe-Cr additives, respectively.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.