• 한국지반환경공학회 논문집
• /
• 제5권2호
• /
• pp.23-31
• /
• 2004

본 연구에서는 침출수 차수재에 Zero Valent Iron (ZVI)를 포함 시켰을 경우, ZVI 함량과 pH에 따른 TCE, 6가 크롬, 질산성질소의 제거능의 변화를 살피고, 반응이 끝난 후 철과 벤토나이트 표면의 철 산화물을 라만 분광기를 통해서 알아보고자 하였다. ZVI의 함량을 중량비로 벤토나이트의 0, 3, 6, 10, 13, 16, 20, 30, 100 w/w% 로 맞춘 9가지의 샘플을 pH7의 완충 용액을 사용했을 경우와 완충 용액을 사용하지 않을 경우 두 가지로 나누어서 실험하였다. Kinetic test 결과, pH7의 완충 용액을 사용하였을 때가 사용하였지 않았을 때보다 TCE의 경우 330시간에서 300시간으로, 6가 크롬의 경우 20시간에서 4시간으로, 질산성질소는 140시간에서 5시간으로 제거 속도가 빨라졌다. 모든 오염물질의 경우 ZVI 함량이 증가할수록 제거 효율이 높아졌으며, pH 7의 완충 용액을 사용하였을 경우 제거 효율도 더 높아지는 것을 볼 수 있었다. 반응 후 철과 벤토나이트의 표면을 라만 분광기를 이용하여 분석한 결과 여러 가지 철산화물이 확인되었다. 이러한 철산화물은 좋은 흡착제의 역할을 할 수 있으며, 이 중 magnetite는 장기간 동안 오염물질의 제거 성능을 유지시켜 줄 수 있다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제30권8호
• /
• pp.1074-1080
• /
• 2017

Objective: The growth, carcass and retail cut yield records on 1,428 Hanwoo steers obtained through progeny testing were analyzed in this study, and their heritability and genetic relationships among the traits were estimated using animal models. Methods: Two different models were compared in this study. Each model was fitted for different fixed class effects, date of slaughter for carcass traits and batch of progeny test live measurement traits, and a choice of covariates (carcass weight in Model 1 or backfat thickness in Model 2) for carcass traits. Results: The differences in body composition among individuals were deemed being unaffected by their age at slaughter, except for carcass weight and backfat thickness. Heritability estimates of body size measurements were 0.21 to 0.36. Heritability estimates of retail cut percentage were high (0.56 from Model 1 and 0.47 from Model 2). And the heritability estimates for loin muscle percentage were 0.36 from Model 1 and 0.42 from Model 2, which were high enough to consider direct selection on carcass cutability traits as effective. The genetic correlations between body size measurements and retail cut ratio (RCR) were close to zero. But, some negative genetic correlations were found with chest girths measured at yearling (Model 1) or at 24 months of age or with chest widths. Loin muscle ratio (LMR) was genetically negatively correlated with body weights or body size measurements, in general in Model 1. These relationships were low close to zero but positive in Model 2. Phenotypic correlation between cutability traits (RCR, LMR) and live body size measurements were moderate and negative in Model 1 while those in Model 2 were all close to zero. Conclusion: Therefore, the body weights or linear body measurements at an earlier age may not be the most desirable selection traits for exploitation of correlated responses to improve loin muscle or lean meat yield.

• 유기물자원화
• /
• 제23권1호
• /
• pp.23-28
• /
• 2015

본 연구는 회분식 실험을 통해 수거 형태에 따른 음식물류 폐기물의 혐기성 분해 특성을 평가하였다. 일반 종량제 봉투 내 음식물류 폐기물 (sample A)의 경우 최종 메탄 수율은 $285.6mL\;CH_4/g$ volatile solids (VS)로 가장 낮게 나타났으며 반응 속도는 $0.215d^{-1}$로 가장 높게 나타났다. RFID 기반의 폐기물 용기 내 음식물류 폐기물 (sample C)의 최종 메탄 수율 $493.4mL\;CH_4/g$ VS로 가장 높게 나타났으며 반응 속도는 $0.162d^{-1}$로 가장 낮게 나타났다. 모든 시료의 율속 단계 결정 계수는 양수로 나타나 메탄 생성 단계가 율속 단계인 것으로 나타났다.

• 한국토양비료학회지
• /
• 제47권6호
• /
• pp.540-546
• /
• 2014

Acid mine drainage sludge (AMDS) has been classified as mine waste and generally deposited in land. For this reason, studies have been conducted to examine the possibility of recycling AMDS as an amendment for heavy metal stabilization in soil. The main objective of this study was to evaluate heavy metal stabilization efficiency of AMDS comparing with the widely used lime stone. Also, optimum mixing ratio was evaluated for enhancing heavy metal stabilization. AMDS and limestone were mixed at the ratio of 0:100, 25:75, 50:50, 75:25, and 100:0 with five different heavy metal solutions ($100mg\;L^{-1}$ of $NaAsO_2$, $CdCl_2$, $CuCl_2$, $Pb(NO_3)_2$, and $ZnSO_4{\cdot}7H_2O$). The amendments were added at a rate of 3% (w/v). In order to determine the stabilization kinetics, samples were collected at different reaction time of 0, 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024 minutes. The heavy metal stabilization by AMDS was faster and higher than those of limestone for all examined heavy metals. While limestone showed only 20% of arsenic (As) stabilization after 1,024 minutes, 96% of As was stabilized within 1 minute by AMDS. The highest effect on the stabilization of heavy metal (loid) was observed, when the two amendments were mixed at a ratio of 1:1. These results indicated that AMDS can be effectively used for heavy metal stabilization in soil, especially for As, and the optimum mixing ratio of AMDS and lime was 1:1 at a rate of 3% (w/v).

• 한국물환경학회지
• /
• 제26권6호
• /
• pp.1028-1033
• /
• 2010

Wastewater reuse for agricultural irrigation needs treatment and control of pathogens to minimize risks to human health and the environment. In order to evaluate the water quality of UV-treated reclaimed water, this study focused on the relationship between micro-pathogens and particulate matters. MS2 was selected as an index organism because it has similar characteristics to human enteric virus and strong resistance to UV disinfection. The turbidity and suspended solid (SS) were selected for test parameters. In this study, it was performed with different UV doses (30 and $60mJ/cm^2$) for estimation of the MS2 inactivation rate using collimated beam batch experiments in the laboratory. The experiment results by turbidity or SS concentration presented that the increased concentration of them lowered MS2 inactivation. At the turbidity (below 4.27 NTU) and SS (below 1.47 mg/L) of the low level range, the inactivation of 60 UV dose is higher than 30 UV dose. However, at the turbidity and SS of the high level, the increasing UV dose did not show apparent increasing the MS2 inactivation. In quantitative microbial risk assessment (QMRA), it can confirm the trend that $P_D$ and turbidity concentrations have positive correlationship at the low concentration, which was also observed in SS. The QMRA can be helpful in communication with public for safe wastewater reuse and be recommended.

• 상하수도학회지
• /
• 제19권1호
• /
• pp.68-77
• /
• 2005

This study was performed to evaluate the application of corrosion inhibitor and to examine the correlation between corrosion rate and red water in a series of batch tests and a test using auto corrosion monitoring system at A water treatment plant in Gyeonggido. The corrosion study in the auto corrosion monitoring system indicated that Fe concentration decreased by 30~50% and corrosion rate also reduced remarkably with corrosion inhibitor at $1.8mg\;PO_4/L$. After addition of corrosion inhibitor, it was indicated the effective adsorption of the inhibitor on the surface of the pipe line forming a protective film. The corrosion rate increases with the increase in Fe concentration. With $1.8mg\;PO_4/L$ of corrosion inhibitor, the corrosion rate decreased remarkably. Fe concentration had correlation to not only red water problems but also the corrosion rate that actually dissolved into the water, primarily due to the deposition of oxidized iron or other compounds as a scale, which serves as a large reservoir of corrosion by-product. Therefore, corrosion rate can be estimated by Fe concentration. For these reasons, an effective corrosion inhibitor is also an effective red water control reagent. The effect of the corrosion inhibition can last for some time even the application the corrosion inhibitor is discontinued. For the cost effective and efficient corrosion control, the concentration and timing of corrosion inhibitor addition must be determined properly.

• 한국환경보건학회지
• /
• 제35권5호
• /
• pp.411-416
• /
• 2009

This study was initiated to improve the cooling water quality by chemical coagulation and sedimentation in steel mills. Due to the inefficient flocculation in the settling tanks of blast furnace cooling water systems, the solid particles in the cooling water overflow accumulate and clog the cooling system. To protect the cooling water system from such fouling, proper flocculants must be continuously used. Laboratory tests were performed for the indirect cooling water system of a plate mill. The batch test in the gas scrubbing cooling water system of a blast furnace showed that the proposed coagulant was more effective for the improvement of coagulation and sedimentation than the existing one. During the tests, cationic flocculants were more effective than use of only an anionic flocculant. The suggested combination of anionic and cationic flocculants can probably improve the turbidity removal efficiency of the cooling water. Proper control of the overflow rate by the designed residence time would help turbidity removal efficiency in the settling tank. In addition, the settling can be enhanced by adopting rapid and slow mixing alternatively. Scale problems in blast furnace cooling water system were reduced to some extent by efficient settling.

• 한국환경과학회지
• /
• 제23권8호
• /
• pp.1419-1428
• /
• 2014

Electron beam-induced grafting polymerization was employed to prepare Acrylic acid-grafted bacterial cellulose (BC-g-AAc). BC-g-AAc as an adsorbent was applied to remove heavy metals (e.g., As, Pb, and Cd). This study examined followings; morphological change of surface, adsorptive behavior of BC-g-AAc, and interpretation of adsorptive kinetics. Specific surface areas of BC and BC-g-AAc were $0.9527m^2g^{-1}$ for BC and $0.2272m^2g^{-1}$ for BC-g-AAc, respectively as measured by BET nitrogen adsorption, revealing the morphological change of the surface of BC-g-AAc. Batch adsorption test was performed to investigate adsorptive behavior of BC-g-AAc in aqueous solution. The amounts of Pb and Cd adsorbed on BC-g-AAc were $69mg\;g^{-1}$ and $56mg\;g^{-1}$, respectively. However, As was not adsorbed on BC-g-AAc due to its neutral nature. Both the Benaissa model and the Kurniawan model were applied in the study to interpret adsorptive kinetics. From the value of correction coefficient ($R^2$), adsorptive kinetics of Pb and Cd were subjected to Kurniawan model referred to pseudo-second-order. Taken together, the results of this study show that BC-g-AAc has potential as a heavy metal (eg., Pb, Cd)-adsorbent made of an environmentally friendly material.

• 대한지하수환경학회지
• /
• 제5권1호
• /
• pp.30-36
• /
• 1998

저분자량 유기산을 이용한 in-situ flushing 토양세척기법의 실제 현장 적용성 검토를 위해 실험실에서 회분식 실험을 통하여 적당한 세척제를 선정하고 이에 따른 여러 가지 운전변수를 찾아보았다. 대상 중금속으로는 Cu를 택했고, 세척제로는 실제 토양환경에 영향이 비교적 적은 저분자량 유기산인 acetic, citric, oxalic, succinic acid를 이용했다. 유기산을 이용하여 처리한 결과 실험에 사용된 유기산들 모두 1 mM의 저농도에서는 효과를 나타내지 못했고 50 mM 이상의 고농도에서 보다 좋은 제거율을 보였는데, 50 mM과 100mM의 경우 제거율이 큰 차이를 보이지 못했다. citric arid와 oxalic acid의 경우 중성 및 약산성 상태에서 최대의 제거율이 나타났고 특히 citric arid의 경우 87.1%의 높은 제거율을 보였다. 유기산이 없을때는 강산성 상태에서 Cu의 최고제거율이 70% 정도였다. 그러나 각 경우에서의 speciation을 살펴보면 유기산이 없을 경우에는 추출된 Cu의 대부분이 유해한 free ion상태로 존재하게 되고 유기산이 있을 경우에는 추출된 Cu의 대부분이 유기산과 complex를 이룬다는 것을 알 수 있었다.

• Journal of Biosystems Engineering
• /
• 제43권2호
• /
• pp.110-118
• /
• 2018

Purpose: In this study, the potential for biogas production, degradation rates, and lag-phase of diauxic growth of carbohydrate-based material, which is one of the proximate compositions, were investigated. Methods: This study was conducted using starch as a carbohydrate-based material. In experimental condition 1, the biogas potential of carbohydrate-based material was measured. In experimental condition 2, the effect of feed to microorganism ratio (F/M ratio) on lag-phase of diauxic growth from carbohydrate-based material was tested. Biochemical methane potential tests were performed at five different feed to microorganism ratios (0.2, 0.4, 0.6, 0.8, and 1.0) under mesophilic conditions. The biogas production patterns, lag-phase, total volatile fatty acids to total alkalinity ratio (TVFA/TA ratio), and time required for 90 percent biogas production were used to evaluate biogas production based on the biochemical methane potential tests. Results: In experimental condition 1, unlike previous studies, biogas was produced in the TVFA/TA ratio ranging from 1.131 to 2.029 (approximately 13-19 days). The methane content in the biogas produced from the digesters was 7% on day 9 and increased rapidly until approximately day 27 (approximately 72%). In experimental condition 2, biogas yield was improved when the feed to microorganism ratio exceeded 0.6, with an initial lag-phase. Conclusions: Even if the TVFA/TA ratio was greater than 1.0, the biogas production was processed continuously, and the $CO_2$ content of the biogas production was as high as 60%. The biogas yield was improved when the F/M ratio was increased more than 0.6, but the lag-phase of carbohydrate-based material digestion became longer starting with high organic loading rate. To clarify the problem of the initial lag-phase, our future study will examine the microbial mechanisms during anaerobic digestion.