• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.1
• /
• pp.35-41
• /
• 2014

This paper presents a design method of programmable low pass filter(PLPF) which reduce an estimation error of a zero crossing point(ZCP) for a high speed brushless DC(BLDC) motor drive. BLDC motor sensorless drive is possible by estimation of ZCP. The ZCP estimated by detecting a change of back-EMF polarity has the estimation error because noises exist on the measured back-EMF. Therefore a calculated commutation timing using the ZCP is inaccurate. And the inexact commutation timing leads to ripples of 3-phase current and degradation of drive performance. This paper proposes the design method of the PLPF to overcome these problems. First, a speed calculated a inaccurate period of the ZCP is analyzed in the frequency domain. Then, the PLPF that has varying cut-off frequency according to change of the speed is designed on the frequency analysis result. The proposed method is verified by the experiment.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.75.2-75.2
• /
• 2011

국내 유인도서의 상당수는 전력의 대부분을 디젤발전으로 생산한다. 향후 발전설비의 교체 혹은 증설이 있을 경우 신재생에너지원 설비의 보급 여지가 있다. 이에 본 연구는 울릉도에 화력발전 설비만을 증설했을 경우와 이를 신재생에너지복합시스템 설비로 대체했을 때의 경제적 타당성을 비교분석한다. 우리는 복합발전 시스템을 풍력터빈, PV, 소수력발전 등의 신재생에너지 설비, Batteries, Converter와 같은 보조전원, 저장 및 back up을 위한 flywheel과 Diesel generator등으로 구성했다. 분석에 사용한 HOMER(Hybrid Optimization for Energy Renewable)는 신재생에너지복합 발전시스템 분석에 사용되며 결과를 NPC(Net Present Cost)의 오름차순으로 제시하여 발전설비구성의 조합들 중 최적의 시나리오를 보여준다. 분석결과 울릉도의 경우 신재생에너지복합 발전의 보급이 잠재적으로 가능할 것으로 보인다. 또한 계통운영의 기술적인 측면을 감안할 경우 정밀한 분석이 가능할 것이다. 따라서 본 연구는 계통운영과 경제성분석 연구의 연계를 위한 사전연구로써 그 의미를 갖는다.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.8 no.1
• /
• pp.12-17
• /
• 2009

In this paper, We play it for the purpose of study about the power amplifier which applied DGS and adaptive bias circuit structure to general Doherty amplifier for the efficiency of a RF power amplifier and a linearity improvement in the WiBro band. As for the IMD3, 3.4dBc was improved with -26.3dBc when we did the measurement result existing Doherty power amplifier and comparison of the Doherty power amplifier which applied an adaptive bias circuit and the DGS which proposed in this paper, and the mean power efficiency verified what was increased in 37%. Also, we were able to know PAE of 36.6% with output power 34.0dBm in P1dB when magnitude of an input signal was 25.6dBm. we did 6dB back off in output P1dB in order to confirm the ACPR which was a nonlinear characteristic and measured the ACPR. we showed the -34.55dBc which was a value of -34.5dBc or below in the 4.77MHz off-set that was a transmission standard. Therefore, we were able to know that we were satisfied with a spectrum mask standard.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.3
• /
• pp.118-123
• /
• 2020

In this paper, the design method of asynchronous nonvolatile memory module that can efficiently process and store large amounts of data without loss when the power turned off is proposed and implemented. PSRAM, which takes advantage of DRAM and SRAM, was used for data processing, and NAND flash memory was used for data storage and backup. The problem of a lot of signal interference due to the characteristics of memory devices was solved through PCB design using high-density integration technology. In addition, a boost circuit using the super capacitor of 0.47F was designed to supply sufficient power to the system during the time to back up data when the power is off. As a result, an asynchronous nonvolatile memory module was designed and implemented that guarantees reliability and stability and can semi-permanently store data for about 10 years. The proposed method solved the problem of frequent data loss in industrial sites and presented the possibility of commercialization by providing convenience to users and managers.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.6
• /
• pp.1135-1141
• /
• 2004

In this study, this system makes use of the analog infrared rays sensor and converts the feature of fish outline when sensor is operating with CPU(80C196KC). Then, after signal processing, this feature is classified a special feature and a outline of fish by using the neural network, one of the artificial intelligence scheme. This neural network classifies fish pattern of very simple and short calculation. This has linear activation function and the error back propagation is used as a teaming algorithm. And the neural network is learned in off-line process. Because an adaptation period of neural network is too long when random initial weights are used, off-line teaming is induced to decrease the progress time.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.90-95
• /
• 2007

Chaotic OOK(On-Off Keying) modulation method can be used in LDR(Low Data Rate) UWB systems. The chaotic generator in one of the most important circuit in this system. The traditional chaotic generator circuits using analog feed back technique have low yield characteristic due to the process variation. A novel quasi-chaotic signal generator using digital PN-sequence in proposed in this paper and verified in 0.18um CMOS teleology.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.174-175
• /
• 2007

A programmable metallization cell (PMC) memory structure with copper-saturated GeTe solid electrolyte films doped by nitrogen was prepared on a TiW bottom electrode by a co-sputtering technique at room temperature. The $Ge_{45}Te_{55}$ solid electrolyte films deposited with various $N_2$/Ar flow ratios showed an increase of crystallization temperature and especially, the electrolyte films deposited at $N_2$/Ar ratios above 30% showed a crystallization temperature above $400^{\circ}C$, resulting in surviving in a back-end process in semiconductor memory devices. The device with a 200 nm thick $Cu_{1-x}(Ge_{45}Te_{55})_x$ electrolyte switches at 1 V from an "off " state resistance, $R_{off}$, close to $10^5$ to an "on" resistance state, Ron, more than 20rders of magnitude lower for this programming current.

• Current Optics and Photonics
• /
• v.5 no.1
• /
• pp.8-15
• /
• 2021

An elliptical zone plate (EZP) array is important in off-axis optical systems because it provides two advantages. First, the residual beam and the main source are not focused in the same direction and second, the light from the observation plane is not reflected back towards the beam source. However, the fill factor of the previous EZP array was about 76% which was a little low. Hence, this EZP array could not collect the maximum amount of illumination light, which affected the overall optical performance of the lens array. In this study, we propose a new EZP array design with a 97.5% fill factor used in off-axis imaging system for enhancement of brightness and contrast. Then, direct laser lithography was used to fabricate the high fill factor EZP array by moving the XY linear stage of the system in a zigzag motion. The imaging properties of the proposed EZP array were experimentally verified at the focal plane and compared with the previous model.

• Composites Research
• /
• v.34 no.2
• /
• pp.77-81
• /
• 2021

Due to the high specific strength and stiffness of the composite materials, the composite materials have been extensively used in various industries. In particular, carbon fiber reinforced composites are widely used in many mechanical structures. In addition, since carbon fiber reinforced composites have anisotropic properties, to understand the fatigue behavior of composites with different fiber orientation is very important for the efficient structural design. Therefore, in this paper, the effect fiber orientation on the fatigue life of composite materials was experimentally evaluated. For this purpose, tensile and fatigue tests were performed on the off-axis specimens (0°, 10°, 30°, 45°, 60°, 90°) of the composite materials. As a result of the fatigue tests, the fatigue strength of the composites decreased significantly as the fatigue strength slightly deviated from 0 degrees. On the other hand, the more deviated, the less decreased. This is because the role of supporting the load of fibers decreased as the stacking angle increased. In addition, the fatigue behavior was analyzed by introducing a fatigue strength ratio (Ψ) that eliminates the fiber orientation dependence of the off-axis fatigue behaviors on the unidirectional composites. The off-axis fatigue S-N lines can be reduced to a single line regardless of the fiber orientation by using the fatigue strength ratio (Ψ). Using the fatigue Ψ-N line, it is possible to extract back to any off-axis fatigue S-N lines of the composites with different fiber orientations.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.489.2-489.2
• /
• 2014

The planar type flexible piezoelectric energy harvesters (PEH) based on PbZr0.52Ti0.48O3 (PZT) thin films on the flexible substrates are demonstrated to convert mechanical energy to electrical energy. The planar type energy harvesters have been realized, which have an electrode pair on the PZT thin films. The PZT thin films were deposited on double side polished sapphire substrates using conventional RF-magnetron sputtering. The PZT thin films on the sapphire substrates were transferred by PDMS stamp with laser lift-off (LLO) process. KrF excimer laser (wavelength: 248nm) were used for the LLO process. The PDMS stamp was attached to the top of the PZT thin films and the excimer laser induced onto back side of the sapphire substrate to detach the thin films. The detached thin films on the PDMS stamp transferred to adhesive layer coated on the flexible polyimide substrate. Structural properties of the PZT thin films were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). To measure piezoelectric power generation characteristics, Au/Cr inter digital electrode (IDE) was formed on the PZT thin films using the e-beam evaporation. The ferroelectric and piezoelectric properties were measured by a ferroelectric test system (Precision Premier-II) and piezoelectric force microscopy (PFM), respectively. The output signals of the flexible PEHs were evaluated by electrometer (6517A, Keithley). In the result, the transferred PZT thin films showed the ferroelectric and piezoelectric characteristics without electrical degradation and the fabricated flexible PEHs generated an AC-type output power electrical energy during periodically bending and releasing motion. We expect that the flexible PEHs based on laser transferred PZT thin film is able to be applied on self-powered electronic devices in wireless sensor networks technologies. Also, it has a lot of potential for high performance flexible piezoelectric energy harvester.