• Transactions on Electrical and Electronic Materials
• /
• 제8권4호
• /
• pp.149-152
• /
• 2007

[ $(Ba_{0.6}Sr_{0.3}Ca_{0.1})TiO_3$ ](BSCT) thick films doped with 0.1 mol% $MnCO_3\;and\;Yb_2O_3(0.1{\sim}0.7mol%)$ were fabricated by the screen printing method on the alumina substrates. And the structural and electrical properties as a function of $Yb_2O_3$ amount were investigated. The exothermic peak was observed at around $680^{\circ}C$ due to the formation of the poly crystalline perovskite phase. The lattice constants of the BSCT thick film doped with 0.7 mol% is 0.3994 nm. The specimen doped with 0.7 mol% $Yb_2O_3$ showed dense and uniform grains with diameters of about $4.2{\mu}m$. The average thickness of all BSCT thick films was approximately $70{\mu}m$. Relative dielectric constant and dielectric loss of the specimen doped with 0.7 mol% $Yb_2O_3$ were 2823 and 3.4%, respectively. The Curie temperature of the BSCT thick films doped with 0.1 mol% $Yb_2O_3$ was $46^{\circ}C$.

• ETRI Journal
• /
• 제35권4호
• /
• pp.587-593
• /
• 2013

We demonstrate semitransparent organic photovoltaics (OPVs) based on thin metal electrodes and polymer photoactive layers consisting of poly(3-hexylthiophene) and [6,6]-phenyl $C_{61}$ butyric acid methyl ester. The power conversion efficiency of a semitransparent OPV device comprising a 15-nm silver (Ag) rear electrode is 1.98% under AM 1.5-G illumination through the indium-tin-oxide side of the front anode at 100 $mW/cm^2$ with 15.6% average transmittance of the entire cell in the visible wavelength range. As its thickness increases, a thin Ag electrode mainly influences the enhancement of the short circuit current density and fill factor. Its relatively low absorption intensity makes a Ag thin film a viable option for semitransparent electrodes compatible with organic layers.

• 한국자기학회지
• /
• 제23권1호
• /
• pp.12-17
• /
• 2013

금속 분말 니켈(Ni)을 HCl용액에 용해시킨 후 $H_3BO_3$, KOH을 첨가하여 Chloride 도금용액을 제조 후 Ni plate 기판에 도금하였다. 도금두께는 $3{\mu}m$로 일정하게 유지하였다. 전류밀도를 $1{\sim}30mA/cm^2$ 변화를 준 결과 전류밀도를 증가시킬수록 Ni 후막표면이 거칠어졌다. $25mA/cm^2$와 $30mA/cm^2$에서는 균열된 표면형상을 관찰하였다. 또한 XRD patterns 변화를 관찰한 결과 전류밀도가 증가할수록 FCC(111)과 FCC(220) 및 FCC(311)상의 강도는 증가한 반면 FCC(200)상의 강도는 감소하는 것을 관찰하였다. 전기도금된 Ni의 수평 및 수직 자화 값을 측정하였는데 기판에 의한 수평자화 값이 크게 나왔고, 코팅층 두께가 증가할수록 수직자화 값이 커지는 것을 확인하였다.

• 한국식품과학회지
• /
• 제23권4호
• /
• pp.437-441
• /
• 1991

원심식 박막증발기를 이용해 마늘착즙을 증발 농축하면서 급액속도가 증발표면에서의 액의 흐름상태와 운전 특성에 미치는 영향에 대해서 조사하였다. 급액속도 $25{\sim}125kg/h$의 운전 조건하에서 증발표면에서의 이론적인 박막의 두께는 $0.52{\sim}0.89mm$ 그리고 체류시간은 $1.77{\sim}6.75$초로 계산되었다. 한편 Reynolds number로 판단해 볼 때 증발표면에서의 마늘착즙의 흐름은 대체로 층류로 여겨졌다. 일정한 증기 및 증발온도 조건하에서 농축비는 급액속도가 증가함에 따라 감소한 반면 증발속도와 총괄열전달계수는 어느 일정한 값까지 증가하다가 감소하는 경향을 나타내었다. 그리고 급액속도 $25{\sim}125kg/h$(증발온도 $40^{\circ}C$, 증기온도 $95{\sim}120^{\circ}C$, 급액의 초기농도 $32^{\circ}Brix$)에서 농축비는 $1.04{\sim}2.04$, 총괄열전달계수는 $3,074.33{\sim}17,614.70kJ/m^{2}{\cdot}h{\cdot}^{\circ}C$ 였다.

• 한국진공학회지
• /
• 제20권6호
• /
• pp.456-460
• /
• 2011

최근 연구 중인 소자들의 크기가 점차 나노 크기를 가짐에 따라서 나노 영역에 대한 물성 분석 연구의 필요성이 대두되고 있다. 특히 나노 크기를 가지는 소자에 대한 기계적 특성은 기존의 마이크로 이상의 소자와는 다른 특성을 보이는 것으로 보고되고 있다. 그러나 이러한 나노 크기에 대한 연구에서 대부분을 차지하는 분광학적, 전기적 방법은 측정 영역 한계와 일정 깊이에 대한 평균적인 정보를 제공하게 된다. 본 연구에서는 나노트라이볼로지 분석의 대표적인 Nano-indenter 분석을 통하여 박막의 수 혹은 수십 나노 미만의 영역과 깊이에 대한 물리적 및 기계적 물성을 연구하였고, Scanning Probe Microscopy를 이용하여 시료 표면 형상을 분석하였으며, 이를 기반으로 수십 나노 이하 두께를 가지는 W-N 확산방지막에 대한 연구를 실시하였다. 연구 결과에 의하면, 박막의 표면 나노강도는 증착 중 질소 유량에 따라서 57.67 GPa에서 9.1 GPa로 급격한 감소가 나타내었고, 또한 탄성계수 역시 575.53 GPa에서 178.1 GPa로 감소되는 것을 확인하였다.

• 한국작물학회지
• /
• 제46권2호
• /
• pp.150-156
• /
• 2001

To explore the feasibility of recycled paper mulching in spring-grown potato the changes of soil environments and the growth and yield of potato under non-mulched control and three mulching treatments of recycled paper (RPM), transparent polyethylene film (TPFM), and black polyethylene film (BPFM) were examined over two spring seasons in 1998 and 1999 at Suwon, Korea. The mulching materials were a recycled mulch paper with 110 g/$m^2$ and a thickness of 0.1mm, which was manufactured from old corrugated containers for this experiment and the commercial polyethylene films with a thickness of 0.01mm. RPM lowered the average soil temperature at 5-cm depth during the potato growing period by 03$^{\circ}C$ compared with the control, whereas TPFM and BPFM raised it by 2.$0^{\circ}C$, and 1.8$^{\circ}C$, respectively. On a sunny day during sprout emergence, RPM reduced the maximum soil temperature by about 5$^{\circ}C$, while TPFM and BPFM enhanced it by about 11$^{\circ}C$ and 6.$0^{\circ}C$, respectively. The temperature difference between the control and the mulching treatments decreased with the development of canopy. All the mulching treatments had an advantage in preserving the soil moisture over the control. RPM and BPFM resulted in the effective control of weed by obstructing light transmission onto soil surface, but TPFM had no control effect of weed. Sprout emergence started two to three days earlier in TPFM and BPFM, but one day later in RPM than in the control due to the altered soil temperature by the mulching treatments. However, the final percentage of emergence was notably lower in TPFM than that in the control because of too high soil temperature during daytime, but was not different among the control, RPM, and BPFM. During the early stage of potato growth, the shoot and root growth under RPM was lower compared with the control, but afterwards, RPM outpaced the control. In 1998 experiment, the tuber yield under RPM and BPFM were significantly higher than those of the control and TPFM. In 1999 experiment, there was no significant difference in tuber yield between RPM and the control.

• 대한방사선기술학회지:방사선기술과학
• /
• 제20권2호
• /
• pp.49-55
• /
• 1997

This study was carried out to investigate radiographical and operating conditions of X-ray units and exposure doses to patients during chest radiography, so that the results could provide basic data used for reducing the exposure dose and for providing the diagnostic information with better quality. The conditions and exposure doses of 100 X-ray units mainly used for chest radiography were examined and also 100 radiological technologists mainly handling those apparatus at 76 medical facilities in Pusan were surveyed using a questionnaire from October 1 to December 31 in 1995. The following results were obtained from the study : 1. It was found that most units were capable of taking a high tube voltage radiography by showing 67% of the units equipped with the maximum tube voltage of 150 kV, 94% with more than 500 mA for the rating capacity and 85% with the full wave type of a signal phase. 2. For actual chest radiographical conditions, however, 80% of the units were operated at $60{\sim}100\;kVp$ and only 14% at 100 kVp and over for the high tube voltage. 3. The average exposure time was less than 0.1 second, and eighty four percent of the units adapted the X-ray tube currents ranging from 200 to 300 mA, 80% the focus-film distances between 180 and 210 cm, and 63% the focus sizes of more than 2.0 mm. 4. Most units(98%) employed additional filters made of aluminum, 75% the thickness of filters less than 2.0 mm, and only 2 units the compound filters. 5. Ortho chromatic system was only adopted in 13% of screen film system for the units, and 73% used the grid ratio at 8 : 1 for the low tube voltage during chest radiography. 6. The average exposure dose of all X-ray units during chest radiography was $371\;{\mu}Sv$ with a difference of about 16 times between the minimum to the maximum, and $386\;{\mu}Sv$ both at hospitals and at health centers, followed by $380\;{\mu}Sv$ at general hospitals and $263\;{\mu}Sv$ at university hospitals without showing any statistically significant differences. In conclusion, since patients during chest radiography at medical facilities in Pusan exposed to high levels of radiation, it is recommended that appropriate added filters and grids necessary for the high tube voltage radiography and high-speed screen systems should be adopted and used as soon as possible in order to reduce exposure dose to the patients.

• 한국전기전자재료학회논문지
• /
• 제37권2호
• /
• pp.164-168
• /
• 2024

(La_0.7Sr_0.3)(Mn_1-xFe_x)O₃ (LSMFO) (x = 0.03, 0.06, 0.09, 0.12) precursor solution are prepared by sol-gel method. LSMFO thin films are fabricated by the spin-coating method on Pt/Ti/SiO₂/Si substrate, and the sintering temperature and time are 800℃ and 1 hr, respectively. The average thickness of the 6-times coated LSMFO films is about 181 to 190 nm and average grain size is about 18 to 20 nm. As the amount of Fe added in the LSMFO thin film increased, the resistivity decreased, and the TCR and B_25/65-value increased. Electrical resistivity, TCR and B_25/65-value of the (La_0.7Sr_0.3)(Mn_0.88Fe_0.12)O₃ thin film are 0.0136 mΩ-cm, 0.358%/℃, and 328 K at room temperature, respectively. The resistivity properties of LSMFO thin films matched well with Mott's VRH model.

• 폴리머
• /
• 제39권1호
• /
• pp.88-98
• /
• 2015

폴리이미드(PI) 나노복합체 필름 제조에 사용된 작용기화 4-amino-N-hexadecylbenzamide graphene sheets (AHB-GSs)는 graphene oxide 분산액에 4-amino-N-hexadecylbenzamide(AHB)를 반응시켜 합성하였다. AHB-GS의 주사탐침 현미경(atomic force microscope, AFM) 이미지와 모식도를 통해서 AHB-GS의 평균 두께가 약 3.21 nm임을 확인하였다. PI는 4,4'-biphthalic anhydride와 bis(4-aminophenyl)sulfide를 사용하여 합성하였다. PI 나노복합체는 0-10 wt%의 다양한 함량의 AHB-GS를 용액 삽입(solution intercalation) 방법을 사용하여 합성하였고, 이미드화는 각각 $250^{\circ}C$ 및 $350^{\circ}C$까지 열 처리하였다. AHB-GS는 대부분 고분자 매트릭스에 잘 분산되었고 약간 뭉친 것도 있었지만 마이크로미터 수준의 입자는 관찰되지 않았다. TEM으로 관찰하였을 때, 평균적으로 입자의 두께는 10 nm 미만이었다. PI 복합체 필름 중 소량의 AHB-GS만으로도 가스 투과도와 전기 전도도는 향상되었지만, 반대로 유리전이 온도와 초기 분해 온도는 AHB-GS의 함량이 10 wt%까지 증가함에 따라 지속적으로 감소되는 경향을 보였다. 전체적으로는, $250^{\circ}C$까지 이미드화한 PI에 비해 $350^{\circ}C$까지 열처리한 PI 필름이 보다 향상된 특성을 보였다.

• 대한치과보철학회지
• /
• 제43권4호
• /
• pp.562-572
• /
• 2005

Statement of problem : Titanium is widely used as an implant material lot artificial teeth. Also, studies on surface treatment to form a fine passive film on the surface of commercial titanium or its alloys and improving bioactivity with bone have been carried out. However, there is insufficient data about the biocompatibility of the implant materials in the body. Purpose: The purpose of this study was to examine whether the precipitation of apatite on titanium metal is affected by surface modification. Materials and methods: Specimens chemically washed for 2 minute in a 1:1:1.5 (in vol%) mixture of 48% HF 60% $HNO_3$ and distilled water. Specimens were then chemically treated with a solution containing 97% $H_2SO_4$ and 30% $H_2O_2$ at $40^{\circ}C$S for 1 hour, and subsequently heat-treated at $400^{\circ}C$ for 1 hour. All specimens were immersed in the HBSS with pH 7.4 at $36.5^{\circ}C$ for 15 days, and the surface were examined with TF-XRD, SEM, EDX and XPS. Also, commercial purity Ti specimens with and without surface treatment were implanted in the abdominal connective tissue of mice for 4 weeks. Conventional aluminium and stainless steel 316L were also implanted for comparison. Results and conclusions : The results obtained were summarized as follows. 1. An amorphous titania gel layer was formed on the titanium surface after the titanium specimen was treated with a $H_2SO_4$ and $H_2O_2$ solution. The average roughness was $2.175{\mu}m$ after chemical surface treatment. 2. The amorphous titania was subsequently transformed into anatase by heat treatment at $400^{\circ}C$ for 1 hour. 3. The average thickness of the fibrous capsule surrounding the specimens implanted in the connective tissue was $46.98{\mu}m$ in chemically-treated Ti, and 52.20, 168.65 and $100.95{\mu}m$ respectively in commercial pure Ti, aluminum and stainless steel 316L without any treatment.