• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.64.2-64.2
• /
• 2010

In order to improve the overall power conversion efficiency in dye-sensitized solar cells (DSSCs), it is very important to secure the sufficient surface area of photocatalytic nanoparticles layer for absorbing dye molecules. It is because increasing the amount of dye absorbed generally results in increasing the amount of light harvesting. In this work, we proposed a new method for increasing the specific surface area of photocatalytic titanium oxide ($TiO_2$) nanoparticles by using an inorganic templating method. Salt-$TiO_2$ composite nanoparticles were synthesized in this approach by spray pyrolyzing both the titanium butoxide and sodium chloride solution. After aqueous removal of salt from salt-$TiO_2$ composite nanoparticles, mesoporous $TiO_2$ nanoparticles with pore size of 2~50 nm were formed and then the specific surface area of resulting porous $TiO_2$ nanoparticle was measured by Brunauer-Emmett-Teller (BET) method. Generally, commercially available P-25 with the average primary size of ~25 nm $TiO_2$ nanoparticles was used as an active layer for dye-sensitized solarcells, and the specific surface area of P-25 was found to be ~50 $m^2/g$. On the other hand, the specific surface area of mesoporous $TiO_2$ nanoparticles prepared in this approach was found to be ~286 $m^2/g$, which is 5 times higher than that of P-25. The increased specific surface area of $TiO_2$ nanoparticles will absorb relatively more dye molecules, which can increase the short curcuit current (Jsc) in DSSCs. The influence of nanoporous structures of $TiO_2$ on the performance of DSSCs will be discussed in terms of the amount of dye molecules absorbed, the fill factor, the short circuit current, and the power conversion efficiency.

• Clean Technology
• /
• v.8 no.3
• /
• pp.119-128
• /
• 2002

In the present study the membrane filtration characteristics of a commercially available synthetic water-based cutting oil through two kinds of ultrafiltration membranes (HF1-45-CM50 and HF1-43-CM100) with molecular weight cut-offs of 50,000 and 100,000, respectively, have been investigated in detail. Among these membranes, the hydrophilic one (HF1-45-CM50) was found to show a satisfactory result for both the permeate flux and the permeability of oil components, whereas the permeate flux obtained with the hydrophobic membrane (HF1-43-CM100) appears to be significantly low, indicating that synthetic cutting oil was easily wetted on the hydrophobic membrane surface and induced more membrane fouling. The effect of material characteristics of the membrane on the filtration characteristics was found to be much more significant compared with the mean pore size of the membrane. Backflushing by nitrogen gas was applied to reduce the formation of a gel layer and membrane fouling. With the hydrophilic membrane, the backflushing was found to increase the permeate flux, whereas the backflushing resulted in a decrease in flux for the hydrophobic membrane. The flux recovery was observed to be highest when the membranes fouled with waste synthetic cutting oil were immersed into a cleaning solution for more than 72 hours and then backflushed by nitrogen gas.

• Journal of Periodontal and Implant Science
• /
• v.36 no.1
• /
• pp.223-237
• /
• 2006

The purpose of the present study was to evaluate the effect of bone graft materials including deproteinized bovine bone(DBB), demineralized freeze-dried bone(DFDB), freeze-dried bone(FDB) on bone formation in guided bone regeneration using perforated titanium membrane(TM). 16 adult male rabbits(mean BW 2kg) were used in this study and 4 rabbits allotted to each test group. Intramarrow penetration(diameter 6.5mm) was done with round carbide bur on calvaria to promote blood supply and clot formation in the wound area. The test groups were devided into 4 groups as follows: TM only(test 1), TM +DBB(test 2), TM +DFDB(test 3), TM +FDB(test 4). Perforated titanium membrane was contoured in rectangular parallelepiped shape(0.5mm pore diameter, 10mm in one side, 2mm in inner height), filled the each graft material and placed on the decorticated carvaria. Perforated titanium membrane was fixed with resorbable suture materials. The animals were sacrificed at 2, 8 weeks after the surgery. Non-decalcified preparations were routinely processed for histologic analysis. The results of this study were as follows: 1. Perforated titanium membrane was biocompatible. 2. Perforated titanium membrane had capability of maintaining the space during the healing period but invasion of soft tissue through the perforations of titanium membrane decreased the space available for bone formation. 3. In test 1 group without bone graft material, the amount of bone formation and bone maturation was better than other test groups. 4. Among the graft materials, the effect of freeze-dried bone on bone formation was best. 5. In the test groups using deproteinized bovine bone, demineralized freeze-dried bone, bone formation was a little. The spacemaking capability of the membrane may be crucial for bone formation. The combined treatment with the perforated titanium membrane and deproteinized bovine bone or demineralized freeze-dried bone failed to demonstrate any added effect in the bone formation. Minimization of size and numbers of perforations of titanium membrane or use of occlusive titanium membrane might be effective to acquire predictable results in the vertical bone formation.

• Biomedical Science Letters
• /
• v.4 no.1
• /
• pp.65-72
• /
• 1998

Recently there have been frequent reports on human infection caused by the Diphyllobothridae in Korea. The adequate opportunities for Koreans to eat raw fish, the primary infection medium of cestodes and the human infection through drinking water by cyclops, the first intermediate host are believed to be main reasons for the infection. The first task of this study was to classify and diagnose the species by differentiating morphological characteristic between scolex and proglottids of cestodes. However, the initially available diagnosis was done with the patient's symptoms and the eggs obtained from his stool. It is important to differentiate the species by the eggs of Diphyllobothrium latum especially in that it can help get advance information for a more reliable analysis in the near future. The morphological and diagnostic results from proglottids and eggs of Diphyllobothrium latum, Diphyllobothrium latum parvum and Spirometra erinacei are as follows； In each kind of cestodes from the patient's stool, the shape and size of 50 eggs were measured. Eggs of Diphyllobothrium latum had an operculum and were ovoidal or ellipsoid to elliptical in shape. Eggs of Diphyllobothrium latum parvum were more ovoidal in shape and smaller in size than Diphyllobothrium latum. And eggs of Spirometra erinacei were asymmetrical in width and long and slender in shape. The average lengths and widths of Diphyllobothrium latum, Diphyllobothrium latum parvum and Spirometra erinacei were 61.4$\times$41.7 $\mu\textrm{m}$, 55.9$\times$41.4 $\mu\textrm{m}$ and 66.7$\times$36.4 $\mu\textrm{m}$, respectively. After the segments of each cestode were fixed, embedding and hematoxylin-eosin dyeing on a microtome-made specimen were done. The micrographs of the semicon's aceto-carmine dyed specimen showed that Diphyllobothrium latum and Diphyllobothrium latum parvum had a centrally-located genital gland and an opened uterine pore. The yolks were observed on both sides of proglottids and had a typical rosette pattern. Yet, Diphyllobothrium latum parvum was shown smaller than Diphyllobothrium latum in the micrograph. Proglottids of Spirometra erinacei displayed that the uterus was rolled spirally more than five to seven times, and connected successively to the seminal vesicle in the cirrus sac. Shown above, this study was performed to measure the size of eggs and analyze the morphological characteristics of proglottids and provided the measurements of three types of cestodes obtained by a light microscope.

• Korean Journal of Environmental Agriculture
• /
• v.20 no.4
• /
• pp.203-210
• /
• 2001

In order to environmentally use wood chips manufactured from low valued forest resources by forest tendering, wood chips were used for the evaluation on chips characteristics, decomposition capability of organic wastes, and field experiment and determination of conditions for decomposer. Bioclusters manufactured by Cryptomeria japonica, commercially available wood chips in Japan, showed higher pore ratio, water reservation and water resistance, and higher cellulose content with lower hot water solubles than domestic wood chips. The useful size of wood chips for swine manure decomposition was 10 (length) ${\times}$ 5 (width) ${\times}$ 2 (thickness) mm, and cellulose contents and alkali solubles of Pinus densiflora and Populus tomentiglandulosa were similar to those of bioclusters. According to the decomposition ratio depending on wood species, it was ordered as Pinus densiflora > Pinus koraiensis > Cryptomeria japonica. The swine manure decomposition ratio depending on treatment hours by Pinus koraiensis was constant with the ratio of 15 to 16 g per hour by 1 kg of chip, indicating of daily swine decomposition amount of 390 kg by 1 ton of chips which was equal to the amount of daily swine manure production by 70 swines. Analyzing by long term used wood chips during 40 days treatment, the treated wood chips characteristically showed stable total nitrogen content, suitable pH, high accumulation of inorganic contents such as calcium, phosphorus, potassium and sodium, and no odor. During winter, the inner temperature of decomposer was kept at $43^{\circ}C$, but air bubble was occurred due to high pH and viscosity of swine manure. The most appropriate mixing ratio between wood chips and swine manure was 1 versus 2 or 3, and at more than ratio 1 versus 3, ammonia gas was caused because of anaerobic fermentation status by high moisture content of wood chips. The mixing interval of decomposer was 3 mins. per hour for the best swine decomposition.