• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.68-75
• /
• 2001

In this paper, a number of supported metal oxides and perovskite type catalysts were investigated for the NOx reduction from the diesel engine exhaust gas. All catalysts were made into pellets type with diameter of 3-4 mm alumina(Al$_2$O$_3$) as a supporter. These samples were tested by real diesel exhaust gas which contains CO, hydrocarbons and soot in the temperature range of 150~55$0^{\circ}C$ with the $3300h^{-1}$ space velocity (SV). Among the results, several promising catalysts showed NOx conversion above 50% in the temperature range of 150-35$0^{\circ}C$. From these results supported metal oxides catalysts and perovskite type could be recommended for the practical application to the automobile exhaust treatments.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.7
• /
• pp.510-519
• /
• 2002

The present study addresses a computational work of the weak shock wave propagating inside an automobile exhaust muffler. Several different types of the silencer systems are employed to investigate the magnitude of the shock wave during propagating through them. The Initial shock wave Mach number $M_s$ is varied between 1.01 and 1.30, and a normal shock wave is given at the inlet of the silencer systems. The second order total variation diminishing scheme Is employed to solve the two dimensional, compressible, unsteady Euler equations. The present computational results are compared with the previous experimental ones available. The present computations predict the experimental results with a quite good accuracy. Of the four silencer systems applied. the most desirable silencer system to reduce the peak pressure at the exalt of the exhaust pipe is discussed from the Point of view of the engineering design of the silencer systems.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.1
• /
• pp.23-30
• /
• 2014

To improve efficiency of diesel engine which requests high output recently and is used all kinds of industrial areas, this thesis experimented dynamic characteristics and exhaust gas characteristics of diesel engine installed by supercharger of correspondent output 200HP and natural inhalation diesel engine through the dynamometer and exhaust gas analyzer in same condition. As the result of experiment with natural inhalation diesel engine and diesel engine installed by supercharger, there were a few differences of output, but dynamic characteristics at high speed showed increased output and efficiency of the engine installed by supercharger. On the contrary, in exhaust gas characteristics, the model installed by supercharger showed increased exhaust gas such as $NO_X$, $O_2$, etc, but added value of exhaust gas is low if considering $CO_2$ reduction and efficiency of dynamic characteristic's increase. Based on the results, diesel engine installed by supercharger is expected to show higher economic feasibility than natural inhalation diesel than natural inhalation engine from an angle of efficiency. Keywords: 200hp class Turbocharger, Exhaust Gas, Engine Performance, Marine Diesel Engine.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.2594-2602
• /
• 2014

As environmental awareness increases, regulations on exhaust gas of automobile, which is a cause of air pollution, have been strengthened. In order to meet emission regulation, automobile companies and engine manufacturers have actively developed the related technologies. Because the emission control has become severe, the systems using electronic motor or solenoid valve for high precise control are needed. For this reason, it is required not only the optimization of composition of components for improving performance and efficiency of the system but also the development of optimal design technology of electronic control system by securing the designing and manufacturing technology of the components. In this paper, it is proposed the position characteristics for electronic EGR valve module through the applied control logic and experiment results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.6
• /
• pp.539-546
• /
• 2006

The Air Quality Sensor(AQS), located near the fresh air inlet, serves to reduce the amount of pollution entering the vehicle cabin through the HVAC(heating, ventilating, and air conditioning) system by sending a signal to close the fresh air inlet door/ventilation flap when the vehicle enters a high pollution area. The sensor module which includes two independent sensing elements for responding to diesel and gasoline exhaust gases, and temperature sensor and humidity sensor was designed for intelligent AQS in automobile. With this sensor module, AVR microcontroller was designed with back propagation neural network to a powerful gas/vapor pattern recognition when the motor vehicles pass a pollution area. Momentum back propagation algorithm was used in this study instead of normal backpropagation to reduce the teaming time of neural network. The signal from neural network was modified to control the inlet of automobile and display the result or alarm the situation in this study. One chip microcontroller, ATmega 128L(ATmega Ltd., USA) was used for the control and display. And our developed system can intelligently reduce the malfunction of AQS from the dampness of air or dense fog with the backpropagation neural network and the input sensor module with four sensing elements such as reducing gas sensing element, oxidizing gas sensing element, temperature sensing element and humidity sensing element.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.1825-1830
• /
• 2014

Environmental emission of recent automobile is drastically enhanced that it is one of the obvious assignments of exhaust system. This study is a purpose to establish of influence distribution on maxima and minima through the location of pressure on exhaust variable valve. The experiment are checked with real angles using camera which exhaust variable valve is opened side of point. Data has extracted to opening angles with internal flow, pressure. Exhaust variable valve through the floating analysis was analyzed the characteristic of location point about pressure and velocity. The pressures indicated the reduced results internal pressure within muffler. The velocity indicated an opposite results and vibration state of valve was verified to be operated as high speed from lower section. The conclusion to obtain from this study was found out the result to make the optimum back pressure condition as more increasing pressure distribution on valve face if the velocity location attracted by bottom point in order to improve for engine performance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.335-342
• /
• 2012

Nowadays, automobile manufacturers are focusing on the reduction of exhaust-gas emissions because of the harmful effects on humans and the environment, such as global warming by greenhouse gases. Gasoline direct injection (GDI) combustion is a promising technology that can improve fuel economy significantly compared to conventional port fuel injection (PFI) gasoline engines. In the present study, ultra-lean combustion with an excess air ratio of over 2.0 is realized with a spray-guided-type GDI combustion system, so that the fuel consumption is improved by about 13%. The level of exhaust-gas emissions and the operation performance with the multiple injection strategy and exhaust-gas recirculation (EGR) are examined in comparison with the emission regulations and from the point of view of commercialization.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4302-4307
• /
• 2011

Recently, various technologies for the fuel efficiency improvement are being developed. The purpose of this study is to evaluate the heat exchanging performance of a exhaust heat recirculation device and to propose a model with optimized performance. The device has been designed to warm up engine coolant as quickly as possible using wasted exhaust heat. To achieve these goals, heat transfer characteristics has been analyzed using CFD for the flow direction effect and in/out location effect of coolant. A method improving the effectiveness of heat exchange has been proposed. As a result, the highest efficiency in heat exchange was observed on condition that exhaust heat affects the coolant directly with a separate flow path between exhaust gas and coolant and that coolant flow rate is relatively low.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.7
• /
• pp.70-75
• /
• 2014

The experiment was done on traveling at the speed of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. The experimental method were employed to measure the waveform of secondary ignition coil and exhaust emission. In this experiment, the correlation between the secondary waveform coming from ignition coil and exhaust emission were measured in decrepit vehicle. The secondary waveform characterized by the value of effective discharge energy. The following results are obtained by analyzing the data relativity between the effective discharge energy and exhaust emission. The variation rate of effective discharge energy was largest 60km/h, 20km/h, 100km/h velocity in the ordered named. As the vehicle velocity increases, the average variation rate of CO and $NO_X$ decreases and that of HC and $CO_2$ decrease. The value of effective discharge energy, CO, $NO_X$ and fuel consumption is measured badly in case of car with failures in MAP, spark plug and good in case of car with before and after maintenance regardless of vehicle velocities. The value of effective discharge energy is to be nearly parabolic shape as vehicle velocity increases. As the value of effective discharge energy increases, the value of $NO_X$, HC and $CO_2$ decrease, the value of CO increase. The most sensible factors of exhaust emission were CO, $NO_X$, and the small variation factors were HC, $CO_2$.

• Journal of Arbitration Studies
• /
• v.22 no.1
• /
• pp.89-110
• /
• 2012

No-fault automobile insurance system is a statutory scheme to provide automobile accident victims with compensation for certain expenses arising from personal injuries occurring in car accidents. New York State has enacted No-Fault Law to ensure that the injured in automobile accidents be paid rapidly by their own insurance company for medical expenses, lost earnings regardless of fault, replacing common law system of reparation for personal injuries under tort law. Its primary purpose is to facilitate compensation without the need to exhaust time-consuming litigation over establishing the existence of fault and the extent of damages. No-Fault Law allows arbitration as a method for settling the no-fault insurance disputes. No-fault arbitration, however, differs in a significant way from general arbitration system. First, No-Fault Law provides the parties with the option to submit any dispute involving no-fault automobile insurance to arbitration. Second, no-fault arbitration attempts to speed its procedure incorporating various methods. Third, the parties are required to seek review of arbitral awards by master arbitrator prior to seeking court's review. Fourth, the parties have right to bring de novo action in court if master arbitrator's award exceeds $5,000. Given the current state of law in Korea, it may not be easy to introduce no-fault arbitration system into Korea in the context of automobile insurance disputes settlement as its law has a long-established reparation system based on tort liability and no-fault arbitration system has its own features that differ from general arbitration system. Nonetheless, it could be suggested that no-fault arbitration be introduced in other fields which require speedy dispute resolution and a third party's decision to settle the disputes. The optional right of submitting disputes to arbitration as provided by No-Fault Law of New York State may offer a ground to supprot the effectiveness of an optional arbitration agreement.