• 제어로봇시스템학회논문지
• /
• 제12권11호
• /
• pp.1088-1094
• /
• 2006

In this paper, an auto path generation and an active compliance grinding control using 3-axis farce sensor are presented. These control algorithms enable the grinding robot to follow unknown path of various workpiece shape pattern. The robot is able to go grinding along unknown paths by position controller managing tangential direction angle and cutting speed, with only information about the start position and the end position. Magnitude and direction of normal force are calculated using force data that go through low pass filter. Moreover, normal and tangential directions are separated for force control and velocity control, respectively.

• Journal of Biosystems Engineering
• /
• 제38권1호
• /
• pp.1-8
• /
• 2013

Purpose: Path planning and tracking algorithms applicable to various agricultural operations, such as tillage, planting, and spraying, are needed to generate steering angles for auto-guidance tractors to track a point ahead on the path. An optimal coverage path algorithm can enable a vehicle to effectively travel across a field by following a sequence of parallel paths with fixed spacing. This study proposes a path generation and tracking algorithm for an auto-guided Korean tractor with a tillage implement that generates a path with C-type turns and follows the generated path in a paddy field. A mathematical model was developed to generate a waypoint path for a tractor in a field. This waypoint path generation model was based on minimum tractor turning radius, waypoint intervals and LBOs (Limit of Boundary Offsets). At each location, the steering angle was calculated by comparing the waypoint angle and heading angle of the tractor. A path following program was developed with Labview-CVI to automatically read the waypoints and generate steering angles for the tractor to proceed to the next waypoint. A feasibility test of the developed program for real-time path tracking was performed with a mobile platform traveling on flat ground. The test results showed that the developed algorithm generated the desired path and steering angles with acceptable accuracy.

• 자동차안전학회지
• /
• 제11권2호
• /
• pp.17-22
• /
• 2019

This paper describes the tracking algorithm performance evaluation for autonomous vehicle using a safety envelope based path. As the level of autonomous vehicle technologies evolves along with the development of relevant supporting modules including sensors, more advanced methodologies for path generation and tracking are needed. A safety envelope zone, designated as the obstacle free regions between the roadway edges, would be introduced and refined for further application with more detailed specifications. In this paper, the performance of the path tracking algorithm based on the generated path would be evaluated under safety envelop environment. In this process, static obstacle map for safety envelope was created using Lidar based vehicle information such as current vehicle location, speed and yaw rate that were collected under various driving setups at Seoul National University roadways. A level of safety was evaluated through CarSim simulation based on paths generated with two different references: a safety envelope based path and a GPS data based one. A better performance was observed for tracking with the safety envelop based path than that with the GPS based one.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.687-692
• /
• 1993

This paper deals with the generation of laser scan path for manufacturing 3-dimensional body using StereoLithography. The purpose of this study is to develop one module of the StersoLithography system(SLA) for Rapid Protyping and Manufacturing. AutoCAD system is used to supply CAD information from model. The X-Y controller which was made for a special purpose is used to test this system. The system software developed is composed of 3 main modules, the first module is calculating the boundary point os laser scan path. The scound module is generating final output file which is used to down load on the controller. The result of this study shows a good algorithm to generate laser scan path on the basis of simple mathematical background.

• 한국레이저가공학회지
• /
• 제15권1호
• /
• pp.6-9
• /
• 2012

In TFT-LCD manufacturing process, various defects are generated by manufacturing machine trouble or particle. These defects can be repaired through the TFT-Laser repair process that only can't be automated in TFT-LCD manufacturing Process. In this Paper, we propose auto defect algorithm for TFT-LCD laser repair machine using image processing algorithm in order to automate process. Proposed algorithm can detect very small defects (< 2um) in 98% success ratio, and generated laser repair path guarantee highly precise position accuracy. Through proposed system, much of the work still done the old-fashioned way, by hand, can be automated and manufacturing company can be strengthed the competitiveness of cost.

• Journal of Positioning, Navigation, and Timing
• /
• 제8권4호
• /
• pp.193-200
• /
• 2019

The auto-encoder network which is a good candidate to handle the modeling of the signal strength attenuation is designed for denoising and compensating the distortion of the received data. It provides a non-linear mapping function by iteratively learning the encoder and the decoder. The encoder is the non-linear mapping function, and the decoder demands accurate data reconstruction from the representation generated by the encoder. In addition, the adaptive network width which supports the automatic generation of new hidden nodes and pruning of inconsequential nodes is also implemented in the proposed algorithm for increasing the efficiency of the algorithm. Simulation results show that the proposed method can improve the neural network training surface to achieve the highest possible accuracy of the signal modeling compared with the conventional modeling method.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.106-111
• /
• 2002

The object of this study is a manufacture of burr die using CAD/CAM systems. Systems are consist of AutoCAD, CAM software and CNC milling machine. CAM software is purpose of G-code generation for CNC programming. Then CAM software and CNC milling machine are connect to RS-232-C cable for networking.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.32-37
• /
• 1998

The object of this study is DNC application of progressive die production process. DNC systems are consis of Auto CAD, CAM software and CNC milling machine. CAM software is purpose of G-code generation for CNC programming. Then CAM software and CNC milling machine are connect to RS-232C cable.

• 자동차안전학회지
• /
• 제11권3호
• /
• pp.30-36
• /
• 2019

This paper suggests a car-following algorithm for urban environment, with multiple target candidates. Until now, advanced driver assistant systems (ADASs) and self-driving technologies have been researched to cope with diverse possible scenarios. Among them, car-following driving has been formed the groundwork of autonomous vehicle for its integrity and flexibility to other modes such as smart cruise system (SCC) and platooning. Although the field has a rich history, most researches has been focused on the shape of target trajectory, such as the order of interpolated polynomial, in simple single-lane situation. However, to introduce the car-following mode in urban environment, realistic situation should be reflected: multi-lane road, target's unstable driving tendency, obstacles. Therefore, the suggested car-following system includes both in-lane preceding vehicle and other factors such as side-lane targets. The algorithm is comprised of three parts: path candidate generation and optimal trajectory selection. In the first part, initial guesses of desired paths are calculated as polynomial function connecting host vehicle's state and vicinal vehicle's predicted future states. In the second part, final target trajectory is selected using quadratic cost function reflecting safeness, control input efficiency, and initial objective such as velocity. Finally, adjusted path and control input are calculated using model predictive control (MPC). The suggested algorithm's performance is verified using off-line simulation using Matlab; the results shows reasonable car-following motion planning.

• 한국정보처리학회논문지
• /
• 제3권6호
• /
• pp.1483-1492
• /
• 1996

본 논문에서는 지리정보시스템을 적용하는 우편 업무와 관련하여, 우편 경로에 대한 관리 및 의사 결정을 수행하는 우편 경로 최적화 시스템을 구성하는 주요 모듈 인 최단 경로 생성 알고리즘에 대한 설계 및 구현에 대하여 다루었다. 최단 경로 생 성 알고리즘 개발을 통하여 효율적인 우편 경로 최적화 시스템을 제시하기 위해 경로 최적화 시스템에 대한 사례 조사와 요구 사항을 분석하였다. 우편 경로 최적화 시스 템의 주요 모듈인 최단 경로 생성 알고리즘은 기존의 그래프 이론에서 제시된 Dijkstra알고리즘뿐 아니라 방향성을 고려한 탐색 방법을 적용하여 시스템이 빠르고 효과적인 경로 탐색을 할 수 있도록 하였다. 우편 경로 최적화 시스템은 최단 경로 생성기, 등거리 생성기, 경로 재배치 생성기의 주요 모듈로 이루어져 있고, 좌표 처 리를 위한 지리정보시스템 엔진과 지형 데이터를 취급하기 위해 공간 데이터베이스를 이용하였다. 이 시스템은 우편 배달 업무의 관리, 배달 구역 및 경로 관리, 경로 재 배치 등에 이용될 수 있으며, 향후에 택배 시스템, 도로 및 교통 정보 안내 등과, GPS(Global Positioning System)와의 연계를 통해 위치 추적 및 자동 운항 시스템에 도 적용될 수 있다.