• 한국분무공학회지
• /
• 제18권3호
• /
• pp.140-145
• /
• 2013

Sub/supercritical spray experiments were conducted, and cryogenic nitrogen and gaseous argon were selected for simulants. liquid nitrogen and gaseous argon were injected in subcritical case, and supercritical nitrogen and near-critical gaseous argon were injected in near-critical/supercritical cases. shadowgraph method was used to visualize spray, and analyzed about the breakup length. The breakup length was measured from numbers of Instantaneous shadowgraph Images from each case, and they were compared with momentum flux ratios and density ratios. It was observed that the relation between breakup length and momentum flux ratio was fitted into former experiment results. and the reasonable constant was suggested about the relation between breakup length and density ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1584-1589
• /
• 2003

This work applies the equilibrium molecular dynamics simulation method to study a Lennard-Jones liquid thin film suspended in the vapor and calculates diffusion coefficients by Green-Kubo equation derived from Einstein relationship. As a preliminary test, the diffusion coefficients of the pure argon fluid are calculated by equilibrium molecular dynamics simulation. It is found that the diffusion coefficients increase with decreasing the density and increasing the temperature. When both argon liquid and vapor phases are present, the effects of the system temperature on the diffusion coefficient are investigated. It can be seen that the diffusion coefficient significantly increases with the temperature of the system.

• Bulletin of the Korean Chemical Society
• /
• 제24권2호
• /
• pp.178-182
• /
• 2003

The stress and the heat-flux auto-correlation functions in the Green-Kubo formulas for shear viscosity and thermal conductivity have non-decaying long-time tails. This problem can be overcome by improving the statistical accuracy by N (number of particles) times, considering the stress and the heat-flux of the system as properties of each particle. The mean square stress and the heat-flux displacements in the Einstein formulas for shear viscosity and thermal conductivity are non linear functions of time since the quantities in the mean square stress and the heat-flux displacements are not continuous under periodic boundary conditions. An alternative to these quantities is to integrate the stress and the heat-flux with respect to time, but the resulting mean square stress and heat-flux displacements are still not linear versus time. This problem can be also overcome by improving the statistical accuracy. The results for transport coefficients of liquid argon obtained are discussed.

• Journal of Welding and Joining
• /
• 제11권1호
• /
• pp.73-79
• /
• 1993

The phenomenon of metal transfer has been investigated for different transfer modes using a digital high speed motion analyzer and an arc shadow-graphing system based on a laser source and related optical system. It was observed that the pinch instability phenomenon did not occur for the globular transfer mode, since the liquid globule was then spherical rateher than a cylindrical liquid bar. On increasing the ratio of carbon dioxide to argon, the transition current from globular to spray transfer generally increased, but it is interesting that the transition was observed to occur at the lowest current in a 5% CO$_{2}$-95% argon gas mixture. For pure carbon dioxide and helium shielding gases, the drop frequency increased slowly with increasing current. At high currents or an argon based shielding gas, the length of liquid bar decreased as the carbon dioxide content increased. The acceleration of a droplet within the arc was determined using the gas drag force theory and was found to be greater than the experimental results.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.197-197
• /
• 2012

Device 제작에 사용된 graphene은 일반적인 lithography 공정에서 resist residue에 의한 오염을 피할 수 없으며 이로 인하여 graphene의 pristine한 성질을 잃어버린다. 본 연구에서는 graphene을 저밀도의 argon inductively coupled plasma (Ar-ICP)를 통해 처리함으로서 graphene based back-gated field effect transistor (G-FET)의 특성변화를 유도한 결과에 대해서 보고한다. Argon capacitively coupled plasma (Ar-CCP)은 에 노출된 graphene은 강한 ion bombardment energy로 인하여 쉽게 planar C-C ${\pi}$ bonding (bonding energy: 2.7 eV)이 breaking되어 graphene의 defect이 발생되었다. 하지만 우리의 경우 저밀도의 Ar-ICP가 적용될 때 graphene의 defect이 제한되며 이와 동시에 contamination 만을 제거할 수 있었다. 소자의 전기적 측정 (Gsd-Vbg)을 통하여 contamination으로 인하여 p-doping된 graphene은 pristine 상태로 회복되었으며 mobility도 회복됨이 확인되었다. Ar-ICP를 이용한 graphene cleaning 방법은 저온공정, 대면적 공정, 고속공정을 모두 만족시키며 thermal annealing, electrical current annealing을 대체하여 graphene 기반 소자를 생산함에 있어 쉽고 빠르게 적용할 수 있는 강점이 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.513-518
• /
• 2004

KARI(Korea Aerospace Research Institute) has developed smart unmaned aerial vehicle(UAV) since 2002. Smart UAV has tilt rotor configuration which can take off and land vertically. For designing and developing smart UAV, it is necessary to obtain design loads. ARGON which use the panel method is multidisciplinary aircraft design program developed and modified by KARI and TsAGI. Panel method is very useful to obtain aerodynamic loads, so it have been used widely for aircraft loads analysis. For flight loads analysis, we have to prepare regulations and load conditions, and then design aerodynamic panel model, mass model and structure model. In this paper, we introduce the flight loads analysis procedure briefly, and show the smart UAV loads analysis procedure and result using ARGON.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.94-97
• /
• 1997

We investigated the sheet resistance properties of tungsten nitride thin films deposited by RF and DC sputtering system. It deposited at various conditions that determine the sheet resistance. The properties of the sheet resistance of these films were measured under various conditions. Sheet resistance analysed under the flow rate of the argon gas and contents of nitrogen from nitrogen-argon gas mixtures. We found that these sheet resistance were largely depend on the temperature of substrate, gas flow rate and RF power. Very high and low sheet resistance of tungsten films obtained by DC sputtering. As the increase of contents of nitrogen gas obtained from nitrogen-argon gas mixture, tungsten nitride thin films deposited by the reactive DC sputtering and the sheet resistance of these films were increased.

• 한국표면공학회지
• /
• 제29권5호
• /
• pp.593-598
• /
• 1996

Previously, in trying to prepare perovskite type oxide powders by microwave heating, we found out a non-equilibrium argon plasma is generated around the powders and discharge continues stable at atmospheric pressure. In this study, we tried the plasma decomposition of heat-stable higher organic compound such as palmitic acid which is the principal constituent of the fimger fats. It was proved that suitable amount of coexistence of oxygen radicals into the argon flow accelerates the decomposition of palmitic acid. The argon-oxygen mixed gas plasma was able to perform a complete elimination of higher organic compound.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.299-301
• /
• 2004

Inductively coupled plasma is commonly used for electrodeless lamp due to its ease of plasma generation. Optical characteristics significantly depend on the RF power and gas pressure of the plasma. This paper describes the measurement of luminous efficacy as a function of RF power and gas pressure with a goal of finding optimal operating conditions of the electrodeless lamp. The gas pressure was varied from 10 [mTorr] to 100 [mTorr] and the RF power was varied from 10 [W] to 120 [W]. It was found that the luminous flux tends to be decreased when argon pressure is increased, and the luminous flux is increased as RF fewer is increased. It was also found that the luminance efficacy is high when the argon pressure is low and when the RF power is low.

• Metals and materials international
• /
• 제24권6호
• /
• pp.1303-1308
• /
• 2018

A new sintering technique for enhancing a densification and hardness of sintered titanium body by supplying hydrogen was developed (Hydrogen Sintering Process, HSP). The HSP was developed by only injecting hydrogen into an argon atmosphere during the core time. As a result, sound titanium sintered bodies with high density and hardness were obtained by the HSP. In addition, a pore size and number of the HSP specimens were smaller than those of the argon atmosphere specimen. It was found that the injecting hydrogen into the argon atmosphere by HSP can prevent the formation of oxide layers, resulting in enhanced densification and hardness.