• Textile Coloration and Finishing
• /
• v.5 no.2
• /
• pp.134-138
• /
• 1993

Wool, silk and nylon 6 fabrics were treated with low-temperature plasma under atmospheric pressure of acetone/argon or helium/argon for 30 and 180 sec, and then dyed with leveling type acid dye, C.I. Acid Red 18 and milling type acid dye, C.I. Acid Blue 83. In spite of short time of the plasma treatment for thirty seconds, the color depth of wool fabrics was increased remarkably with both of the plasma gases, aceton/argon or helium/argon and with the kinds of dyes i.e., levelin type or milling type. But the atmosperic low-temperature plasmas did not increase the depth of silk and nylon 6 fabrics dyed with both of the acid dyes regardless of the teated time and plasma gases. It seems that low-temperature plasma by atmospheric-pressure discharge is effective for improvement of dyeing of wools as is the same way with the low-temperature plasma by glow discharge. The kinds of plasma gases and treated time did not influnce the depth of wool fabric pretreted with the atmosperic low-temperature plasmas.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.4
• /
• pp.67-73
• /
• 2011

For loads analysis of airplane, applicable regulation should be determined. Then, loads conditions are prepared from the regulation. Modeling for aerodynamic, mass, and structure are performed. Panel method is usually adopted for aircraft loads analysis to obtain air loads. The ARGON which is a multidisciplinary fixed wing aircraft design software co-developed by the KARI and TsAGI are used for loads analysis. The ARGON can be utilized for flutter and stress analysis as well as for flight and ground loads analysis. In this paper, flight loads analysis for wing structural design of the regional aircraft at the conceptual design phase are performed with the ARGON. FAR 25 is used for the regulation for the load analysis. Shear force, bending moment and torsion diagrams for the wing and shear force and hinge moment for the aileron are presented.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.2
• /
• pp.77-83
• /
• 2013

In this study, we aimed to determine the optical properties of the plasma used for the dry cleaning method. The optical properties of the atmospheric pressure plasma device were measured through the degree of ionization of hydrogen or nitrogen gas by ionized atmospheric gas. The degree of ionization of hydrogen or nitrogen is closely associated with surface modification. We observed through our experiments that argon gas, an atmospheric gas, caused an increase in the ionization of nitrogen gas, which has similar ionization energy. This type of increase in nitrogen gas ions is believed to affect surface modification. The results of our study show that the pressure of argon gas and the partial pressure of argon and nitrogen gases lead to different results. This important result shows that argon ions can affect the ionization of nitrogen gas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.323-326
• /
• 1998

The current-voltage characteristic have been measured in a gas stabilized DC arc generated in a non-transferred arc plasma torch operating on a mixture of argon and nitrogen. Relation between voltage and current to these arcs has been examined by plasma power and current under different flow rates and gas mixture ratios. Firstly, the voltage and current of arc plasma used argon was measured and secondly, in argon-nitrogen mixed gas regime, the flow rate of nitrogen was increased slowly. When the flow rate of nitrogen was increased, electrode drop of potential was increased.

• Journal of Welding and Joining
• /
• v.5 no.4
• /
• pp.12-21
• /
• 1987

To investigate the suitability of nitrogen gas as an internal purging gas, various properties of GTA welded joints of duplex, 316L stainless steel, Cu-Ni alloy pipe using nitrogen purging gas were evaluated with reference to onew purged with argon gas. Mechanical properties evaluated by the tensile, bending test, and hardness value of welded joints with nitrogen gas purging did not show any difference those with argon gas. General and local corrosion rates of each welded joint prepared by nitrogen gas purging also showed no difference with those prepared by argon gas. Based on the present test results it is confirmed that nitrogen is a suitable purging gas for GTA welding of stainless steels and nonferrous piping systems, which can be used at lower cost instead of argon.

• 전기의세계
• /
• v.26 no.2
• /
• pp.104-110
• /
• 1977

This paper investigates temperature distribution of plasma jets which used argon gas, and nitrogen gas mixed with argon as working fluids in spectroscopic method, and studies correlations between them main results are as follows; 1) The temperature at the center of plasma jet increases with are current and gas flow, and decreases with magnetic flux density along the axial direction. 2) The changing rate of temperature of plasma jet in the radial direction decreases rapidly beyond 2mm from central axis. 3) Temperature drop rate of plasma jet in the central axis direction appears most apparant beyond 13mm above the nozzle exit. 4) When argon gas mixed with a small amount of nitrogen, plasma temperature increases at same are current compared with the case of argon gas only.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.8
• /
• pp.1371-1374
• /
• 2007

The velocity auto-correlation (VAC) function of liquid argon in the Green-Kubo formula decays quickly within 5 ps to give a well-defined diffusion coefficient because the velocity is the property of each individual particle, whereas the stress (SAC) and heat-flux auto-correlation (HFAC) functions for shear viscosity and thermal conductivity have non-decaying, long-time tails because the stress and heat-flux appear as system properties. This problem can be overcome through N (number of particles)-fold improvement in the statistical accuracy, by considering the stress and the heat-flux of the system as properties of each particle and by deriving new Green-Kubo formulas for shear viscosity and thermal conductivity. The results obtained for the transport coefficients of liquid argon obtained are discussed.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.2
• /
• pp.327-346
• /
• 1996

The purpose of this study was to evaluate the shear bond strengths, microhardness, compressive strength and contraction gap at the resin-tooth interface of two types of composite resins polymerized with visible light and argon laser sourse. The results from the present study can be summarized as follows ; 1. Resin samples polymerized either by argon laser or visible light did not show significant difference in their physical properties tested(p>.05). 2. The contraction gap at the resin tooth interface was found to be present in all samples but any significant difference between groups could not be established due to their variability. Although the superiority of argon laser over visible light in enhancing the physical properties of resin could not be elucidated in the present study, continous efforts are deemed to be worthwhile to investigate this area using different conditions and materials of experiment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.3
• /
• pp.11-18
• /
• 1996

Liquid droplets of water and argon surrounded by their vapor have been simulated by the milecular dynamics method. To explore the surface phenomena of clusters, each molecule is classified into 'liquid', 'surface', or 'vapor' with respect to the number of neighbor molecules. The contribution of a 'surface' molecule of the water cluster to the far infrared spectrum is almist the same as that of the 'liquid' molecule. Hence, the liquid-vapor interface is viewed as geometrically and temporally varying boundary of 'liquid' molecules with only a single layer of 'surface' molecules that might have different characteristics from the 'liquid' molecules. The time scale of the 'phase change' of each molecule is estimated for the argon cluster by observing the instantancous kinetic and potential energies of each molecule. To compare the feature of clusters with macroscopic droplets, the temperature dependence of the surface tension of the argon cluster is estimated.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.36-39
• /
• 1999

Steel tire cords were coated via RF Plasma Polymerization of acetylene in order to enhance adhesion to rubber compounds. Adhesion of tire cords was measured by TACT as a function of plasma polymerization and argon etching conditions such as power, treatment time and chamber pressure. Tested tire cords were analysed by SEM to elucidate the adhesion mechanism. The highest adhesion values were obtained with argon etching condition at 90W, 10min, 30mtorr followed by acetylene plasma polymerization condition at 10W, 30sec., 30mtorr. In SEM analysis, the plasma polymerized tire cord at the optimized condition showed 100% rubber coverage as observed from brass-plated steel tire cords.