• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.8
• /
• pp.844-851
• /
• 2005

The purpose of this study was to determine feasibility of application of regenerated or recycled $TiO_2$ on the successive treatment of Cu(II)-EDTA. The recovery of copper, the reuse of $TiO_2$ and the assessment of acute toxicity was studied in the total eight successive photocatalytic reactions. Aqueous solution of $10^{-4}\;M$ Cu(II)-EDTA was treated using an illuminated $TiO_2$ at pH 6 in a circulating reactor. Two different procedures were applied in the reuse of $TiO_2$: i) recycle of $TiO_2$ without acid wash ii) regeneration of $TiO_2$ with acid wash to remove adsorbed copper in a previous experiment. The averaged decomplexation rate constant($k'_{obs}$) of Cu(II)-EDTA in recycle of $TiO_2$ without acid wash was approximately 45% less than that in regeneration of $TiO_2$ with acid wash. Removal of Cu(II) was near complete after 180 minutes in the total eight successive photocatalytic reactions using the regenerated $TiO_2$ after acid wash. In contrast, removal of Cu(II) was minimum at total fifth successive photocatalytic oxidation using the recycled $TiO_2$ without arid wash. The recovered $TiO_2$ was approximately 86% in average in each procedure. The recovered Cu(II) was 67.9% in average. The acute relative toxicity of the treated water rapidly declined at an initial reaction time up to 60 minutes but little declination was observed after 60 minutes due to little degradation of DOC. Relative toxicity of treated water using the recycled $TiO_2$ without acid wash we some what well correlated with the concentration of dissolved Cu(II). From this work, it is suggested that Cu(II)-EDTA can be effectively treated using an integrated cyclic photocatalytic oxidation with recovery of $TiO_2$ and Cu(II).

• Economic and Environmental Geology
• /
• v.48 no.6
• /
• pp.491-500
• /
• 2015

Batch experiments were performed to determine the feasibility of the surfactant-enhanced soil washing process at various washing conditions for the Kuwait soil seriously contaminated with the crude oil. The soil was sampled at a dried oil pond in Kuwait and its average TPH concentration was 223,754 mg/kg, which was too high to apply the conventional remediation process. Nine commercialized non-ionic surfactants were used for the batch experiment to measure the surfactant solubility for the crude oil because it was reported that they have worked for the soil remediation. Among them, three surfactants having high crude oil solubility were used for the soil washing experiment. From the result of batch experiment, 5% TritonX-100 washing solution showed the highest TPH removal efficiency (67%) for the crude oil contaminated soil. However, because the residual TPH concentration in the washed soil was still higher than the clean-up level in Kuwait (10,000 mg/kg), the repeated soil washing was performed. After five washings with 2% surfactant solution, the cumulative TPH removal efficiency was higher than 96% and the residual TPH concentration in the soil went down below the clean-up level. To measure the desorption capacity of TritonX-100 remained in the soil after the soil washing, the silica beads and the soil were washed five times with 2% TritonX-100 surfactant solution and then they were washed again with distilled water to detach the surfactant adsorbed on beads or soil. After five washings with surfactant solution, 7.8% and 19.6% of the surfactant was adsorbed on beads and soil, respectively. When additionally washed with distilled water, most of the residual surfactant were detached from beads and only 4.3% of surfactant was remained in soil. From the results, it was investigated that the surfactant-enhanced soil washing process with TritonX-100, Tergitol S-15-7, and Tergitol S-15-9 has a great capability for the remediation of the Kuwait soil seriously contaminated by crude oil (more than 220,000 mg/kg).

• Radiation Oncology Journal
• /
• v.24 no.3
• /
• pp.185-191
• /
• 2006

[ $\underline{Purpose}$ ]: Standardization quality assurance (QA) program of CyberKnife for suitable circumstances in Korea has not been established. In this research, we investigated the development of QA program for CyberKnife and evaluation of the feasibility under applications. $\underline{Materials\;and\;Methods}$: Considering the feature of constitution for systems and the therapeutic methodology of CyberKnife, the list of quality control (QC) was established and divided dependent on the each period of operations. And then all these developed QC lists were categorized into three groups such as basic QC, delivery specific QC, and patient specific QC based on the each purpose of QA. In order to verify the validity of the established QA program, this QC lists was applied to two CyberKnife centers. The acceptable tolerance was based on the undertaking inspection list from the CyberKnife manufacturer and the QC results during last three years of two CyberKnife centers in Korea. The acquired measurement results were evaluated for the analysis of the current QA status and the verification of the propriety for the developed QA program. $\underline{Results}$: The current QA status of two CyberKnife centers was evaluated from the accuracy of all measurements in relation with application of the established QA program. Each measurement result was verified having a good agreement within the acceptable tolerance limit of the developed QA program. $\underline{Conclusion}$: It is considered that the developed QA program in this research could be established the standardization of QC methods for CyberKnife and confirmed the accuracy and stability for the image-guided stereotactic radiotherapy.

• Geophysics and Geophysical Exploration
• /
• v.9 no.4
• /
• pp.279-290
• /
• 2006

The borehole radar methods used to tunnel detection are mainly classified into borehole radar reflection, directional antenna, crosshole scanning, and radar tomography methods. In this study, we have investigated the feasibility and limitation of each method to tunnel detection through case studies. In the borehole radar reflection data, there were much more clear diffraction signals of the upper wings than lower wings of the hyperbolas reflected from the tunnel, and their upper and lower wings were spreaded out to more than 10m higher and lower traces from the peaks of the hyperbolas. As the ratio of borehole diameter to antenna length increases, the ringing gets stronger on the data due to the increase in the impedance mismatching between antennas and water in the boreholes. It is also found that the reflection signals from the tunnel could be enhanced using the optimal offset distance between transmitter and receiver antennas. Nevertheless, the borehole radar reflection data could not provide directional information of the reflectors in the subsurface. Direction finding antenna system had a advantage to take a three dimensional location of a tunnel with only one borehole survey even though the cost is still very high and it required very high expertise. The data from crosshole scanning could be a good indicator for tunnel detection and it could give more reliable result when the borehole radar reflection survey is carried out together. The images of the subsurface also can be reconstructed using travel time tomography which could provide the physical property of the medium and would be effective for imaging the underground structure such as tunnels. Based on the results described above, we suggest a cost-effective field procedure for detection of a tunnel using borehole radar techniques; borehole radar reflection survey using dipole antenna can firstly be applied to pick up anomalous regions within the borehole, and crosshole scanning or reflection survey using directional antenna can then be applied only to the anomalous regions to detect the tunnel.

• Progress in Medical Physics
• /
• v.25 no.4
• /
• pp.255-263
• /
• 2014

The dosimetry of very small fields is challenging for several reasons including a lack of lateral electronic equilibrium, large dose gradients, and the size of detector in respect to the field size. The objective of this work was to evaluate the suitability of a new commercial synthetic diamond detector, namely, the PTW 60019 microDiamond, for the small field dosimetry in cyberknife photon beams of 6 different collimator size (from 5 mm to 30 mm). Measurements included dose linearity, dose rate dependence, output factors (OF), percentage depth doses (PDD) and off center ratio (OCR). The results were compared to those of pinpoint ionization chamber, diamond detector, microLion liquid Ionization chamber and diode detector. The dose linearity results for the microDiamond detector showed good linearly proportional to dose. The microDiamond detector showed little dose rate dependency throughout the range of 100~600 MU/min, while microLion liquid Ionization chamber showed a significant discrepancy of approximately 5.8%. The OF measured with microDiamond detector agreed within 3.8% with those measured with diode. PDD curves measured with silicon diode and diamond detector agreed well for all the field sizes. In particular, slightly sharper penumbras are obtained by the microDiamond detector, indicating a good spatial resolution. The results obtained confirm that the new PTW 60019 microDiamond detector is suitable candidate for application in small radiation fields dosimetry.

• Radiation Oncology Journal
• /
• v.22 no.4
• /
• pp.316-324
• /
• 2004

Purpose : In radiotherapy of tumors in liver, enough planning target volume (PTV) margins are necessary to compensate breathing-related movement of tumor volumes. To overcome the problems, this study aims to obtain patients' body movements by using a moving phantom and an ultrasonic sensor, and to develop respiration sating techniques that can adjust patients' beds by using reversed values of the data obtained. Materials and Methods : The phantom made to measure patients' body movements is composed of a microprocessor (BS II, 20 MHz, 8K Byte), a sensor (Ultra-Sonic, range $3\~3$ m), host computer (RS232C) and stepping motor (torque 2.3 Kg) etc., and the program to control and operate it was developed. The program allows the phantom to move within the maximum range of 2 cm, its movements and corrections to take place In order, and x, y and z to move successively. After the moving phantom was adjusted by entering random movement data (three dimensional data form with distance of 2 cm), and the phantom movements were acquired using the ultra sonic sensor, the two data were compared and analyzed. And then, after the movements by respiration were acquired by using guinea pigs, the real-time respiration gating techniques were drawn by operating the phantom with the reversed values of the data. Results : The result of analyzing the acquisition-correction delay time the three types of data values and about each value separately shows that the data values coincided with one another within $1\%$ and that the acquisition-correction delay time was obtained real-time $(2.34{\times}10^{-4}sec)$. Conclusion : This study successfully confirms the clinic application possibility of respiration gating techniques by using a moving phantom and an ultrasonic sensor. With ongoing development of additional analysis system, which can be used in real-time set-up reproducibility analysis, it may be beneficially used in radiotherapy of moving tumors.

• Korean Journal of Weed Science
• /
• v.12 no.2
• /
• pp.144-157
• /
• 1992

The study was conducted to compare the interprete methods and examine the feasibility of mixture use of oxyfluorfen and bensulfuron in controlling principal Paddy weeds, annuals and perennials. Application ratio of both chemicals were obtained from the combinations of 5 levels(0, 5, 10, 15, 20 g ai/ha) of each chemicals, respectively. All the treatments were applied at 5 days after transplanting and water was maintained at 3.0cm in depth. Shoot fresh-weight of weeds was assessed at 35 days after treatments. Data obtained was analysed by Colby, Isobole, Calculus, Regression and EQM method, respectively. The results from the analysis of variance on the principal weeds treated with oxyfluorfen and bensulfuron showed significant interactions at 1% level on both Echinochloa crus-galli and Eleocharis Kuroguwai, and total species at 0.5% level on both Potamogeton distinctus and Cyperus serotinus, but non significant on Scirpus juncoides and Sagittaria pygmaea. Thereafter, the results of the models applied to Echinochloa crus-galli, Eleocharis kuroguwai and total species were as follows ; 1. The Colby method gave values nearly identical to regression estimate method (both multiplicative models) as provided by Akobundu et al. The Colby method and Regression method indicated synergistic toward Echinochloa curs-galli, and total species, but antagonistic toward Eleocharis kuroguwai. 2. The Isobole method shows synergism on Echinochloa crus-galli at $ID_{50}$, and total species at $ID_{60}$ on Eleochari kuroguwai. 3. The Calculus method gave positive signs for the first differentiation and negative signs for the second differentiation except for some rates on Echinochloa crus-galli and total species, but reverse on Eleocharis kuroguwai. These result does not agree with the observed values. 4. ${\theta}$ value from the EQM method was greater than one at all combinations. This result was quite different from those of other methods. 5. The various models did not show the same results, but mixture of oxyfluorfen and bensulfuron tend to have synergistic effect. Weeding effect also was high. Treatment in terms of two chemical combination was expected to reduce rates, and to enhence weeding efficacy compared with single treatment.

• Korean Journal of Heritage: History & Science
• /
• v.49 no.1
• /
• pp.100-119
• /
• 2016

The concept of "original form" and the principle of "maintaining the original form" take center stage in conservation, management, and promotion of the domestic heritage. Introduced in the 20th century, there were little discussion or deliberation about the concept of "original form" therefore it remains a vague and somewhat abstract notion subject to individual interpretation. Without a specified practical meaning, "maintaining the original form" became the fundamental principle for heritage conservation and management in the 1999 version of the Cultural Heritage Protection Act, engendering difficulties in applying the principle in practice. Conceived as an important first step toward resolving the issues stemming from the indistinct concept of "original form," this paper explores the process through which the concept was introduced to Korea and then established and developed as a legal principle for heritage conservation, management, and promotion. While the examination of the related documents and various cases shows that the development of the concept of "original form" has centered on specific periods and architectural styles, this essay explicates that the notion "original form" is commonly used as a term referring to the form at the earliest possible temporality. It also explains that this view emanates from perceiving heritages not as multivalent objects, but as a material object that exclusively carries aesthetic and, more importantly, historical value, and that comes from the history awareness of the times. This essay suggests that the concept "original form" should be reestablished with full consideration of the diverse values of heritage and diverse forms through which heritage can be expressed. After reviewing the feasibility and practicality of the concept a set of concrete guidelines should be presented for application in practice.

• Journal of the Society of Disaster Information
• /
• v.18 no.1
• /
• pp.202-217
• /
• 2022

Purpose: The recent increased use of Personal Mobility (PM) has been accompanied by a rise in the annual number of accidents. Accordingly, the safety requirements for PM use are being strengthened, but the laws/systems, infrastructure, and management systems remain insufficient for fostering a safe environment. Therefore, this study comprehensively searches the main problems and improvement methods through a review of previous studies that are related to PM. Then the priorities according to the importance of the improvement methods are presented through the Delphi survey. Method: The research method is mainly composed of a literature study and an expert survey (Delphi survey). Prior research and improvement cases (local governments, government departments, companies, etc.) are reviewed to derive problems and improvements, and a problem/improvement classification table is created based on keywords. Based on the classification contents, an expert survey is conducted to derive a priority improvement plan. Result: The PM-related problems were in 'non-compliance with traffic laws, lack of knowledge, inexperienced operation, and lack of safety awareness' in relation to human factors, and 'device characteristics, road-drivable space, road facilities, parking facilities' in relation to physical factors. 'Management/supervision, product management, user management, education/training' as administrative factors and legal factors are divided into 'absence/sufficiency of law, confusion/duplication, reduced effectiveness'. Improvement tasks related to this include 'PM education/public relations, parking/return, road improvement, PM registration/management, insurance, safety standards, traffic standards, PM device safety, PM supplementary facilities, enforcement/management, dedicated organization, service providers, management system, and related laws/institutional improvement', and 42 detailed tasks are derived for these 14 core tasks. The results for the importance evaluation of detailed tasks show that the tasks with a high overall average for the evaluation items of cost, time, effect, urgency, and feasibility were 'strengthening crackdown/instruction activities, education publicity/campaign, truancy PM management, and clarification of traffic rules'. Conclusion: The PM market is experiencing gradual growth based on shared services and a safe environment for PM use must be ensured along with industrial revitalization. In this respect, this study seeks out the major problems and improvement plans related to PM from a comprehensive point of view and prioritizes the necessary improvement measures. Therefore, it can serve as a basis of data for future policy establishment. In the future, in-depth data supplementation will be required for each key improvement area for practical policy application.

• Journal of Korea Entertainment Industry Association
• /
• v.15 no.1
• /
• pp.131-142
• /
• 2021

Purpose: Clinical practicums via non-face-to-face methods were inevitable due to the COVID-19 pandemic. We developed an online program for emergency nursing care and identified the feasibility of the program and the learning achievements of students. Methods: This was a methodological study. The program was developed by three professors who taught theory and clinical practicum for adult nursing care and clinical experts. Students received four hours of video content and two task activities every week in four-week program. Real-time interactive video conferences were included. Qualitative and qualitative data were collected. Results: A total of 96 students participated in the program. The mean score for overall satisfaction with the online program was 4.72(±1.02) out of 6. Subjects that generally had high learning achievement scores were basic life support care, fall prevention, nursing documentation, infection control, and anaphylaxis care. As a result of a content analysis of 77 reflective logs on the advantages of this program, students reported that "experience in applying nursing process," "case-based learning and teaching method," and "No time and space constraints" were the program's best features. Conclusion: Collaboration between hospitals and universities for nursing is more important than ever to develop online content for effective clinical practicum.