• 펄프종이기술
• /
• 제39권4호
• /
• pp.45-52
• /
• 2007

Whole, bast and core fibers of kenaf cultivar Tainung-2 were pulped under different pulping methods, thermomechanical and kraft pulping methods. The physical and optical properties of kenaf TMP(thermomechanical pulp) and KP(kraft pulp) handsheets were investigated and the results from the study are summarized as follows: Yields of TMP and KP were $77{\sim}87%\;and\;43{\sim}52%$, respectively. There was no significant change in apparent density between kenaf KP and USKP(unbleached softwood kraft pulp) but TMP showed a little lower apparent density. Bast pulp had the lowest apparent density regardless of pulping methods. Tensile strength of kenaf KP was higher than that of TMP but similar to that of USKP. Both TMP and KP handsheets of bast fraction showed the highest tear strengths among whole, bast, and core fractions. Core fraction showed the lowest tear strengths under different pulping methods. In general burst strength of kenaf pulp under different pulping methods was lower than that of USKP, and kenaf pulp had better stiffness than USKP. Brightness of kenaf KP and TMP was higher than that of USKP. There was no significant variation in opacity between kenaf pulp and USKP even though kenaf pulp showed a little lower opacity. The main difference in paper quality between the core fiber and bast fiber is derived from the fact that bast fiber is long and thin, whereas core fiber is short and thick.

• 자원리싸이클링
• /
• 제25권6호
• /
• pp.92-97
• /
• 2016

Spray dried $Cr_2O_3$ 분말은 겉보기밀도를 향상시키기 위해 plasma flame에 투입하여 실험을 진행 하였다. 첫번째 고밀도화 공정에서의 분말은 입자내부 공간까지 완전히 용해되어지지 않았으며, 두번째 공정 이후 완전히 용해가 되었다. 두번째 공정 결과 분말 입도는 작아졌으며, 용해 및 표면 연화에 의해 겉보기 밀도와 유동도는 향상이 되었다. 두번째 고밀도화 공정이 후 부분적으로 입자들이 $30{\mu}m$ 이상의 hollow structure을 보여주고 있다. 분말의 이러한 고밀도화는 plasma flame에 의해 응집되어진 응집체내의 열전도율 및 내부 가스압의 관점에서 정량적으로 논의 하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1405-1407
• /
• 2001

It was studied to prepare high temperature heating elements using molybdenum disilicide($MoSi_2$). Molybdenum disilicide is widely used as material for manufacturing high temperature heating elements. $MoSi_2$ heating elements could be used at 1700-1900$^{\circ}C$. However, it is relatively expensive, and its demand depends on import. $MoSi_2$ powders was mixed with 4-5wt% of montmorillonites type bentonite as plasticizer and a small amount of $Si_3N_4$, $ThO_2$, and B as additives to prepare specimen of heating elements. Then, it was extruded, dried, sintered and machined followed by heating test. Effects of sintering conditions and amount of additives were investigated, It was sintered effectively at 1,350$^{\circ}C$ for five hours. Electrical resistivity was decreased with increasing of sintering temperature and time, and related with apparent density of the specimens. It was linealy decreased with increasing of sintered density. The heating elements thus prepared was stable at 1700$^{\circ}C$ and the physical properties such as specific electrical resistivity, hardness, apparent density, thermal expansion coefficient, and bending strength were almost identical with those of commercial heating elements.

• 한국분말재료학회지
• /
• 제5권1호
• /
• pp.28-34
• /
• 1998

Plasma sprayed ceramic coatings are widely used in various industrial fields to improve their properties or to reduce the production cost. The ceramic powders for plasma spray coating have been mainly manufactured by spray drying or fused+crushed process. In this study, chromium oxide which has better mechanical properties than those of the other ceramic was selected and agglomerated chromium oxide powders for plasma spray coating were produced by spray drying process with a various processing condition. The large hollow powders and the harsh surfaced powders are formed at high slurry feed rate more than 163 g/min. and low binder concentration less than 2wt%, respectively. These powders cause the considerable decrease of flowability and apparent density. The powders produced by spray drying process have the spherical shape with the mean size of 45 ${\mu}m$, but these are shown lower apparent density and flowability than the powders produced by fused+crushed powders. The plasma spray coated layers by spray dried powders are shown a different microstructure with that by fused+crushed powders in porosity shape, but their properties such as density, hardness and bond strength are similar.

• 한국작물학회지
• /
• 제37권4호
• /
• pp.313-319
• /
• 1992

토양수분 부족이 콩식물체의 엽운동, 광합성능, 증산량, 수량 및 관련 형질에 미치는 영향을 조사하기 위해서, '단엽콩', '방사콩', '보광콩', '무한콩'을 비닐하우스 내에 폿트 재배에서 2주간 단수처리하여 실험을 하였다. 1. 광합성능은 광량(0.887$^{**}$ ), 기공전도율(0.788$^{**}$ ) 및 엽온(0.744$^{**}$)과 고도의 유의적인 정 상관이 있었다. 2. 1일중 광량과 온도가 증가함에 따라 콩의 복엽중 중앙의 소엽은 측렬의 소엽에 비해 더 빨리 엽운동이 시작되고 광합성능이 높은 반면에 수광량, 엽온은 다소 낮았다. 3. 한발구에 비해 관수구의 광량은 358 umole $m^{-2}$ $s^{-1}$, 기공전도율은 0.2 mole $m^{-2}$ $s^{-1}$, 엽온은 9$^{\circ}C$, 증산량 3.7 mole $m^{-2}$ , 광합성능은 8.5 $CO_2$, $\mu$mole $m^{-2}$ $s^{-1}$이 각각 높았다. 4. 관수구에 비해 한발구의 수량 및 관련 형질이 다양하게 감소되었다 ; 개체당 건물중 8%, 개체당 근류중 7%, 근중 14%, 간장 3%, 분지수 7%, 경태 8%, 개체당 협수 17%, 개체당 립중 17%가 각각 감소되었다.

• 대한치과기공학회지
• /
• 제34권2호
• /
• pp.113-119
• /
• 2012

Purpose: Zirconia blocks for all ceramic dentures are divided into two groups. One is pre-heated block and the other is binder added block. In this study, the possibility of recycling the remained parts of binder added block after CAD/CAM machining with slip casting process was investigated. Methods: Owing to the binder added block contain large amount of organic matter, Binder burn-out was must be carried out before ball milling for preparing the casting slip. Binder burn-out was accomplished at $600^{\circ}C$ for 10 hours. Ball milling was performed with 5mm zirconia ball and 60mm polyethylene bottle. From 0% to 5% at 1% intervals of alumina was added to zirconia powder for preparing slip. Solid casting was achieved with plaster mold. Cast bodies were dried and sintered at $1,500^{\circ}C$ for 1 hour. Linear shrinkage, apparent porosity, water absorption, bulk density, and flexural strength were tested. Microstructures were observed by SEM, EDS and XRD analysis were executed. Results: Optimum slips for casting was prepared with 300g ball, 100g powder, and 180g distilled water. Cast body without alumina showed 26% of linear shrinkage, 6.07 of apparent density, and 470MPa of three point bend strength. On the other hand, as received zirconia block, which was sintered at the same conditions, showed 23% of linear shrinkage, 6.10 of apparent density, and 680MPa of three point bend strength. When 3% of alumina was added to zirconia, sintered body showed 23% of linear shrinkage, 6.10 of apparent density, and 780MPa of three point bend strength. SEM photomicrographs and EDS analysis showed alumina particles uniformly dispersed in zirconia matrix, and XRD analysis showed no phase transformation of tetragonal zirconia particles was occurred when alumina was added. Conclusion: According to the all of this experimental results, 3% of alumina added cast zirconia body showed excellent mechanical properties more than as received binder containing zirconia block.

• 전기화학회지
• /
• 제2권2호
• /
• pp.88-92
• /
• 1999

리튬이온전지용 $LiCoO_2$ 전극의 도전재료인 흑연과 블랙에 대하여 도전재료 함량에 따른 복합체 전극의 겉보기 밀도, 전해액 중에서 집전체로부터 전극복합체의 자기박리 및 전자전도 저항 특성을 조사하였다. $LiCoO_2$복합전극의 겉보기 밀도는 도전재료의 함량 증가에 따라 감소하였으며, 복합체 중 $LiCoO_2$ 단독의 겉보기 밀도는 보다 큰 감소를 나타내었다. $4.7\%w/w$ 이상의 super s black 도전재료를 사용한 전극은 propylene carbonate와 diethyl carbonate의 1: 1 체적비 혼합용매 중의 1 mol/I $LiPF_6$ 전해액 함침으로 자기박리하였으며, 흑연 도전재료에서는 자기박리가 없었다 복합전극의 전자전도에 대한 비저항은 도전재료의 함량 증가에 따라 감소하였으며, super s black도전재료 $2\~3\%w/w$ 함량의 비저항은 Lonza KS6흑연 도전재료 $12\%w/w$ 함량의 비저항과 유사하였다. 본 연구에서 나타낸 범위 내에서 super s black도전재료를 사용할 때 전극 복합체 중의 $LiCoO_2$밀도가 높아 고용량을 나타내었다.

• 천문학회보
• /
• 제39권1호
• /
• pp.47.1-47.1
• /
• 2014

We examine the effect of environment on star formation activity of a sample of galaxy group catalogue given in Tempel et al.(2012) constructed from the Sloan Digital Sky Survey Data Release 8. In order to compare galaxies in different environment, we classify galaxies into two groups: galaxies in low density environment and galaxies in high density environment. After matching colors and apparent magnitudes of the galaxies, we are left with 5912 galaxies in each of the environment category. The fraction of star-forming galaxies in low-density environment is ~34%, higher than ~15% in high-density environment. Star-forming galaxies in low density environment have a higher average SFR value than those in high density environment. The bulge-to-disk ratio for galaxies in two different environment shows bimodal distribution. Regardless of the environment, we find galaxies with high star formation rate despite their red (g-r) color, for which the origin enhancing their star formation rate is investigated.

• 자원리싸이클링
• /
• 제9권2호
• /
• pp.33-39
• /
• 2000

생물여과법에 의한 유해성 유기물 제거용 저밀도 담체로 사용하기 위하여 석탄회를 출발물질로 이용하여 세라믹 담체를 제조하였다. 석탄회에 기공 조절용 및 탄소함량 조절용으로 밀가루를 첨가하여 약환원성 분위기를 유지하여 $1200^{\circ}C$에서 소결한 결과 1.6~1.8 g/$\textrm{cm}^3$의 겉보기 밀도를 얻을 수 있었다. 소결 시 공기를 차단하고 급속히 승온하여 시편 조성의 일부를 환원시킴으로써 액상을 형성할 수 있었으며, 이렇게 형성된 액상은 시편의 표면부근에 폐기공을 형성하여 밀도를 낮추었다.

• 대한의용생체공학회:의공학회지
• /
• 제19권2호
• /
• pp.171-176
• /
• 1998

본 연구에서는 뼈의 특성을 파악하는 초음파감쇠 파라미터를 재평가하였다. 초음파 속도, 특정 주파수(0.5MHz)에서의 초음파감쇠 및 광역 밴드 초음파감쇠와 같은 초음파 파라미터들을 해면골 입방체 시편의 세 직교방향(전/후, 내/외, 상/하)에서 측정하였다. 그리고 컴퓨터 영상장치를 사용하여 골밀도를 측정했으며, 골 시편의 무게와 부피를 이용하여 외형밀도도 함께얻었다. 이와같이 구해진 외형밀도와 초음파 속도로부터 초음파 탄성영률을 계산하였다. 주파수 0.5MHz에서의 초음파감쇠와 광역밴드감쇠는 골밀도 및 세 직교방향의 초음파 영률과 서로 관련시켜 연관성을 조사하였다. 그 결과 특정 주파수 초음파감쇠가 골밀도 및 탄성영률을 평가하는 능력에 있어서 광역밴드 감쇠보다 우수함을 알 수 있었다. 따라서 광역밴드 초음파감쇠를 측정하여 골의 상태를 평가하는 형행 초음파 진단 기법이 재검토 되어야 하며 본 연구에서 증명된 특정주파수(0.5MHz) 초음파감쇠를 이용하여 골 다공증 진단 예측율을 향상시킬 수 있다.