• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.3
• /
• pp.109-114
• /
• 2008

The solenoid valve of ABS hydraulic modulator is a two directional on-off valve and is controlled by around 100Hz on-off control. When the on-off valve is switched from open state to closed state, there are braking force deterioration, noise and vibration due to surge pressure in the wheel cylinder. In this study, identifies surge pressure in the braking process of ABS, and investigates the way to reduce the phenomenon. To reduce the surge pressure, PWM(Pulse Width Modulation) control with high frequency of 20kHz was attempted. In conclusion, by using the results of this study for the pressure surge prediction, we could expect enhancement of braking performance in ABS.

• International Journal of Internet, Broadcasting and Communication
• /
• v.8 no.4
• /
• pp.48-53
• /
• 2016

Noise and vibration pollution is emerging to people in high speed trains. And it is difficult to realization of eco-friendly railway system at noise problem. The railway internal noise is 73dB on average and over 80dB in the loudest section. In order to reduce noise, there are passive methods that are far from noise sources and theother active noise reducion method. In this paper, we propose a method of reduce noise by measure and estimate the noise condition of train environment using Bone-Conduction device. We use an anti-phase waveform for canceling of noise characteristic. With this new system, the noise from surrounding environments can be reduced.

• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.192-194
• /
• 2006

Backlash between meshing gear teeth causes impact, tracking error and undesired vibrations. It is usually minimized by precision gear, spring-loaded anti-backlash gears and precise mechanical adjustment. Although these techniques can help to reduce the backlash gap, its cost is relatively high and performance is limited. And the classic controller is insufficient to control the dynamic system with nonlinearity. For these reason, a fuzzy controller is proposed to compensate the backlash effect at a robot system. The input variables are position error and change in error. The output variable can be defined by input voltage of motor. The performance of a fuzzy controller is verified by comparing with a PID controller. The results show that the undesired vibration is suppressed. And then diminishing the position error is observed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.5
• /
• pp.425-429
• /
• 2007

A linear ultrasonic motor was designed by a combination of the longitudinal and bending mode. linear ultrasonic motors are based on an elliptical motion on the surface of elastic body, such as bar or plates. The corresponding eigen-mode of one resonance frequency can be excited twice at the same time with a phase shift of 90 degrees in space and time. That is excite symmetric and anti-symmetric modes. Then it determines the thrust and speed of the motor. Linear ultrasonic motors are investigated experimentally in according to be fabricated a general classification to motor structure and material characteristic. There was the first to simulate as use of finite element analysis ANSYS 9.0. The AL-T2W8-ARM14-LEG18-ANGLE80 motor has a maxim efficiency 18 % under the speed 0.14 m/s, thrust 345 gf and preload 280 gf, operating frequency is 57.6 kHz.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.538-539
• /
• 2010

자기 베어링 시스템은 축과 베어링간의 자기적 힘을 이용하여 축을 비접촉으로 지지함으로써 고속으로 회전하는 회전체의 마찰손을 저감시킨다. 고속 회전체에 편심(Eccentricity)이 있을 경우 편심 질량으로 인한 원심력이 속도의 제곱에 비례하여 발생하게 되고, 축을 지지하고 있는 베어링에 과도한 진동을 유발하게 된다. 베어링에 전해지는 진동이 커지게 되면 진동 자체도 문제일 뿐 아니라 베어링이 부담해야 하는 힘의 크기가 커지게 되어 자기 베어링 및 이를 구동하는 전력전자 기기의 용량을 증가시켜야 하는 문제가 있다. 본 논문에서는 베어링의 지지력을 능동적으로 제어하는 능동 자기 베어링을 사용하여 축의 편심 질량의 크기 및 편심 위치를 파악하고 회전 관성 중심점으로 축을 회전시킴으로써 회전 진동을 저감하는 방법을 제안하고, 실험 결과로써 제안된 방법의 타당성을 검증한다.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.589-592
• /
• 2005

In general, the function of intake structure, whether it be a open channel, a fully wetted tunnel, a sump or a tank, is to supply an evenly distributed flow to a pump station. An even distribution of flow, characterized by strong local flow, can result in formation of surface or submerged vortices, and with certain low values of submergence, may introduce air into pump, causing a reduction of capacity and efficiency, an increase in vibration and additional noise. Unfortunately in order to design the sump station, the reasonable code or the standards weren't presented yet in Korea. Thus, some researchers had often referred the HI code, JSME code or CEN code to design the sump station. This study aims to prescribe the standard of sump design which were matched well the Korean pump station. Thus, the HI code and TSJ code would be interpreted fully to Korean language, the part of interpreted clauses of the western codes would be selected to compose the standard.

• Journal of KSNVE
• /
• v.2 no.2
• /
• pp.99-106
• /
• 1992

The complex Young's modulus of a viscoelastic material can be obtained as a function of frequency from the measurements of relative motion between the two ends of a bar-type specimen. Non-resonance method is usually used to obtain the complex Young's modulus over wide range of frequency including resonance points, while in resonance method information at resonance frequencies only is used. However, the complex Young's modulus obtained by the non-resonance method is often unreliable in the anti-resonance frequency regions because of the measurement noise problems. In this study, the effects of the random measurement errors on estimating the complex Young's modulus are studied in the aspect of sensitivity, and how to obtain the reliable frequency region for a given measurement error level is shown. The usable frequency regions in determining the complex Young's modulus are represented by a non-dimensional parameter formed with the wave length and specimen length.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.292-295
• /
• 2002

Transducer for linear ultrasonic motor with symmetric and anti-symmetric modes was studied. The transducer was composed of two Langevin-type vibrators that cross at right angles with each other at tip. In order to excite two vibration modes, two Langevin-type vibrators must have 90-degree phase difference with each other. As a result, tip of transducers moves in elliptical motion. In this paper, elliptical trajectory of transducer was analyzed by employing the finite element method.

• Journal of the Korean Society of Safety
• /
• v.24 no.6
• /
• pp.150-156
• /
• 2009

The oil pressure switch(OPS) for automobile is very important part to prevent an overheated engine and other problems by checking the operation of an engine oil system and displaying oil signs on a dashboard. OPS is the part that receives various stress caused by temperature, vibration, and corrosion in an engine room. Regarding existing steel OPS cases, there occur field errors due to the rust, and much concern comes from the low anticorrosion caused by CR6+ Free according to the restrictions of heavy metals. Therefore, the study analyzed average life, the failure rate, and reliability through the tests of performance according to temperature changes, mechanical strength, and run-test in order to confirm if the use of the oil pressure switch with Al of anti-corrosion can improves the reliability, instead of the existing steel products.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.250-253
• /
• 1997

Generally, Piezoelectric ceramics based lead-zirconate-titanate(PZT) system are well known to use in high power devices. In this pacer. Pb(Mn$\sub$1/3//Sb$\sub$2/3/)O$_3$(PMS) ceramics which have been shown to be adaptable for a high power usage is introduced. The stability of piezoelectric properties in PZ-PT-PMS solid solution system such as piezoelectric constants. electromechanical coupling coefficient and mechanical quality factor is discussed by the addition effect of CeO$_2$ as a additive. The CeO$_2$ ratio ranges from 0 to 2 wt%. The resonant and anti-resonant frequencies. mechanical quality factor, and force factor are also measured as a function of vibration velocity