• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.11
• /
• pp.1190-1197
• /
• 2003

The purpose of this study is to compare and analyze methods of women's apparel prototypes and provide for some useful fundamental data to improve the apparel prototype suitable for Korean women. Two different drafting methods, the Bunka pattern of Japan Bunka Women's University and the Secoli pattern of Italy istituto carlo secoli, an italian pattern drafting institute, were selected. The result and discussion are as follows; In the calculation formula, the Bunka was shown more comfort at arm-hole part, because of it's lower arm-hole depth, wider arm-hole width and lower cap height in comparison with the Secoli. At the shoulder angle, the Bunka is inclined more in front shoulder than the back shoulder, whereas the Secoli is inclined more in back shoulder than the front shoulder. It could explain that the Bunka is suitable for bendforward type and the Secoli is suitable for lean-back type. In the sensory test, the one-piece pattern of the Secoli with 4cm ease was highly estimated in ease. It seems young women's preference to body conscious clothes which reflected in many new elastic fabrics. At the bust point to neck, the Bunka was highly estimated, compared with the Secoli. It seems like to be caused that for the bust point to neck formula, the Bunka used bust girth, the Secoli used stature which has low correlation with the bust point to neck.

• Journal of the Ergonomics Society of Korea
• /
• v.25 no.2
• /
• pp.51-62
• /
• 2006

In assessing risks related to working posture, pictures of postures are taken from various directions, which can be a source of observation error. Joint postures of the neck, lower back, knee, shoulder, and elbow were taken from 7 different viewing angles and 19 observers estimated joint angles by observing the pictures in 2-dimensional display. The joint angles were also measured using an optoelectronic motion measurement system. The estimation error increased as the viewing angle varies from the right side of the human body, but the patterns differ according to which joint angles were being observed. Guidelines to increase the validity of observation of joint angles were presented based on the results. In general, it is recommended to maintain the viewing angle within 20 degrees from the right side of the human body, while different ranges of viewing angle are recommended for each joint angle.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.1
• /
• pp.113-127
• /
• 1996

In this study, the pattern was copied by the method of Tight Fitting Techinque, which resulted from the changed body by the upper limb motion-front-vertical motion(or vertical motion in front), side-vertical motion, and horizontal motion. And, this study analyzed the change of the pattern and the observed items dimension changed to the pattern. The results are as follows: 1. In the observation of the degree of the pattern change according to the motion of upper limb, the result provides that the motion change in the range of $135^{\circ}$ to $180^{\circ}$ is the largest in front-vertical motion, $45^{circ}~90^{\circ}$ in side-vertical motion, and $0^{circ}~45^{\circ}$ in horizontal motion respectively. 2. The probability test result of the items of the motion is more related with the horizontal width item rather than the vertical length item in the front and back pattern where the back pattern has more effect than the front pattern. And the upper limb-surrounding items are more related than any otheer item. 3. The change of the pattern according to the motion shows the decrese of the neck width and the shoulder legth, the rising of the point of shoulder (or shoulder point) and armpit point, the decrease of the pattern width and the increase of the pattern length. As the angle of the motion grows vertically motion. The change of the shoulder length in the horizontal motion is smaller than that vertical. But as the angle of the motion grows horizontally, it has a tendency of decreas in th width of the front patten and the length of the pattern, whereas the width of the back pattern is noticeably increases.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.36 no.3
• /
• pp.311-323
• /
• 2012

This study establishes the initial data to develop a well-fitted underwear pattern by categorizing and analyzing torso types based on body measurements of women in their 50s and 60s. The results are as follows: First, the statistical assessment on the body measurements showed meaningful differences among age groups in twenty seven items (except for bust breadth, hip width armscye depth, hip depth, neck base circumference, armscye circumference, chest circumference, hip circumference, bishoulder length, shoulder length, front interscye, back interscye, weight and inclined angle of left shoulder). Women in their early 50s and late 60s (respectively) showed the highest values in height and depth. Second, there are five body factors according to the results of the factor analysis: Factor 1 (circumference, width, and depth of upper body measurements) - the degree of body depth and obesity, Factor 2 (height and vertical length) - The vertical torso length, Factor 3 - the size of shoulder, Factor 4 - the vertical upper body length, and Factor 5 - the size of shoulder angle. Third, the results of the cluster analysis showed that there are four distinctive body types. The largest number of the study subjects was related to Type 3 (30.69%), followed by Type 2 (26.78%), Type 1 (25.84%), and Type 4 (16.69%), respectively. For distribution of age groups by body type, Type 3 was the most common among the 60s group while Type 2 appeared most frequently among the 50s.

• Clinics in Shoulder and Elbow
• /
• v.20 no.2
• /
• pp.90-94
• /
• 2017

Background: Proximal humerus fracture is considered to be the third most common fracture for patients aged 65 years or older. Conservative treatment has been known to treat most of humerus fracture. However, fractures with severe displacement or dislocation may require surgical treatment. Intramedullary fibular allograft with a locking plate is frequently used in patients accompanying medial metaphyseal disruption. In this study, author intends to evaluate clinical and imaging results based on patients who underwent surgical treatment using fibular allograft with a locking plate. Methods: This study is conducted prospectively at Wonju Severance Christian Hospital, targeting patients who previously underwent surgical treatment using open reduction and intramedullary fibular allograft with a locking plate between 2011 and 2015. A total of 26 patients were evaluated on the following: postoperational clinical assessment measuring Constant score, American Shoulder and Elbow Society (ASES) score, and the Disabilities of the Arm, Shoulder and Hand (DASH) score. Postoperational imaging assessments are evaluated via measuring the neck-shaft angle. The study subject were Neer classification type 3, 4 proximal humerus fracture cases with disrupted medial hinge and having cortical comminution in the region of the surgical neck. Results: The average period of progression was 22.5 months, and the average age of patients was 72.6 years. At the final follow-up, the average Constant, average ASES, and average DASH scores were 80.1, 78.5, and 20.6 respectively. The average neck-shaft angle was $127.5^{\circ}$. Conclusions: In conclusion, fibular allograft augmentation with a locking plate showed satisfying results in both clinical and imaging studies.

• The Journal of Advanced Prosthodontics
• /
• v.5 no.2
• /
• pp.187-197
• /
• 2013

PURPOSE. The purpose of this study was to evaluate various core designs on stress distribution within zirconia crowns. MATERIALS AND METHODS. Three-dimensional finite element models, representing mandibular molars, comprising a prepared tooth, cement layer, zirconia core, and veneer porcelain were designed by computer software. The shoulder (1 mm in width) variations in core were incremental increases of 1 mm, 2 mm and 3 mm in proximal and lingual height, and buccal height respectively. To simulate masticatory force, loads of 280 N were applied from three directions (vertical, at a $45^{\circ}$ angle, and horizontal). To simulate maximum bite force, a load of 700 N was applied vertically to the crowns. Maximum principal stress (MPS) was determined for each model, loading condition, and position. RESULTS. In the maximum bite force simulation test, the MPSs on all crowns observed around the shoulder region and loading points. The compressive stresses were located in the shoulder region of the veneer-zirconia interface and at the occlusal region. In the test simulating masticatory force, the MPS was concentrated around the loading points, and the compressive stresses were located at the 3 mm height lingual shoulder region, when the load was applied horizontally. MPS increased in the shoulder region as the shoulder height increased. CONCLUSION. This study suggested that reinforced shoulder play an essential role in the success of the zirconia restoration, and veneer fracture due to occlusal loading can be prevented by proper core design, such as shoulder.

• Physical Therapy Korea
• /
• v.17 no.2
• /
• pp.25-32
• /
• 2010

The purpose of this study was to investigate the most effective and comprehensible method for the assessment of resting scapular position (RSP) and pain level (PL) in unilateral shoulder pain (USP). Fifty volunteers with USP were involved in the study. Resting scapular assessments of the patients' pain sides (PS) and non-pain sides (NPS) were evaluated. The assessment tools for RSP are: 1) sternal notch (SN) to coracoid process (CP) distance 2) 3rd thoracic spinous process (T3S) to posterolateral angle of acromion (PLA) distance 3) scapular index 4) 8th thoracic spinous process (T8S) to inferior angle of scapular (IAS) distance 5) supine measurement of pectoralis minor (PM) distance 6) standing PM distance 7) PM index (PMI) and 8) PM pain. The paired t-test was used to compare PS and NPS in RSP. Pearson correlation analysis was used to confer a relationship between the PL and RSP. The results of this study indicated that: 1) all the variables between the PS and NPS for RSP were statistically significant(p<.05) and 2) the PMI showed the strongest relationship in the correlation analysis between RSP and PL(p<.05, r=.37). Therefore, it can be concluded that there is a relationship between PMI and PL and it is suggested that an assessment tool using PMI to diagnose shoulder pain would be clinically effective.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.15 no.1
• /
• pp.32-40
• /
• 2009

Purpose: The purposes of this study were to determine the intertester and intratester reliabilities of the Lateral Scapular Slide Test (LSST) method, and to examine if significant differences existed in scapular positions among the pain groups (right-shoulder pain group, left-shoulder, pain group and both-shoulders pain group). 27 female subjects (mean age = 51.6, mean height = 157.7 cm, mean weight = 57.5 kg) with shoulder pain were recruited for this study. Methods: The bilateral distances between the root of the scapular spine and T3/4 (RSS), and between the inferior scapular angle and T7/8 (IA), were recorded. Subjects were tested at three positions: the with arms with abducted at 0, 45 and 90 degrees in the coronal plane. The LSST measurements were performed by two testers, selected randomly. Results: The results were as follows: Intraclass correlation coefficients (ICCs) for the intertester reliability were excellent (ICC 0.78-0.94). And the ICCs for the intratester reliability were excellent (ICC 0.83-0.99). In the right-shoulder and both-shoulders pain groups, the right-side RSS and IA values of right side were significantly greater than of the left-side RSS values left side for the arms abducted at 0 degrees of right shoulder pain group and both shoulder pain group (p<.05). However, the side-to-side difference was less than 1.5 cm. Conclusion: Our results suggest that the LSST is highly reliable in identifying the abnormal scapular position of patients with shoulder problems. Future research should be continued to clarify the clinical usefulness of this method.

• Physical Therapy Rehabilitation Science
• /
• v.12 no.3
• /
• pp.214-221
• /
• 2023

Objective: This study aimed to assess the impact of using the LED light electromyographyfeedback system (EMG-light) during Pilates exercises in women to maintain consistent muscle contraction in the abdominal external oblique muscles and reduce muscle contraction in the upper trapezius muscles. This study compared Pilates training using the EMG-light with Pilates training only in healthy women for 4 weeks. Design: This study was conducted as a cross-sectional study. Methods: A total of 17 healthy women were divided into an experimental group (n=9) and a control group (n=8). Both groups performed Pilates exercises as assigned, twice per week for four weeks, with each session lasting fifty minutes. The experimental group were used the EMG-light feedback system during pilates exercise while the control group did not use EMG-light. We used cervical vertebral angle (CVA), shoulder tilt angle to evaluate neck posture and standing balance with closed eye for 30s before and after exercise. Results: The control group exhibited a significant change in CVA (p<0.05). Both groups showed significant changes in shoulder tilt, center of pressure (COP) path-length, and COP velocity during eyes-closed conditions (p<0.05). However, there were significant differences between the experimental and control groups in terms of CVA, shoulder tilt, COP path-length, and COP velocity. Conclusions: This study demonstrated that Pilates exercises had positive effects on shoulder posture and balance. The use of EMG-light provided real-time visual feedback on muscle contraction during Pilates exercise. However, the experimental group did not show significant improvements compared to the control group, which performed Pilates exercises without feedback.

• Physical Therapy Korea
• /
• v.24 no.2
• /
• pp.48-57
• /
• 2017

Background: Rounded shoulder posture (RSP), a postural abnormality, might cause shoulder pain and pathologic conditions. Although most previous research has investigated RSP focusing on the proximal structures of the shoulder, such as the scapula and pectoralis muscles, the relationship between RSP and anterior distal structures of the upper extremity, such as the biceps brachii muscle and elbow joint, is not clearly understood. Objects: This study aimed to investigate the correlations between RSP and the biceps brachii length, elbow joint angle (EJA), pectoralis minor length, general pectoralis major length, humeral head anterior translation (HHAT), glenohumeral internal rotation (IR), external rotation (ER), and horizontal adduction (HAD). Methods: Twelve subjects with RSP (6 male, 6 female) were recruited. All subjects fulfilled the RSP criteria indicated by a distance ${\geq}2.5cm$ from the posterior aspect of the acromion to the table in the supine position. The examiner measured each of the following parameters twice: RSP, biceps brachii length, EJA, pectoralis minor length, pectoralis major length, HHAT, glenohumeral IR, ER, and HAD. Pearson's correlation coefficient(r) was used to assess the correlation between RSP and all the variables. Results: There was a significant moderate positive correlation between RSP and biceps brachii length (r=.55, p=.032), moderate negative correlation between RSP and pectoralis minor length (r=-.62, p=.015), and moderate positive correlation between RSP and HHAT (r=.53, p=.038). Conclusion: The biceps brachii length, pectoralis minor length, and HHAT could be used to evaluate patients with RSP. Better understanding of the correlation between these factors and RSP could help in the development of effective methods to treat patients with this condition in clinical management.