• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1348-1353
• /
• 2006

This paper is concerned with the comparison of component mode synthesis md substructure synthesis methods. Those two methods were developed for the dynamic analysis of complex structure. However, the difference between two methods in solving the dynamic problem has never been explained. In this paper, a structure consisting of two beams is considered for the application of two methods. The dynamic formulation shows the characteristics and differences of two methods. The procedure for choosing proper substructure modes in each method is explained in detail. In addition, the advantage of the substructure synthesis method is discussed based on the numerical example. Numerical examples show how two methods are applied to the addressed problem.

• Korean Journal of Materials Research
• /
• v.33 no.10
• /
• pp.385-392
• /
• 2023

A solution combustion process for the synthesis of hollandite (BaAl₂Ti₆O₁₆) powders is described. SYNROC (synthetic rock) consists of four main titanate phases: perovskite, zirconolite, hollandite and rutile. Hollandite is one of the crystalline host matrices used for the disposal of high-level radioactive wastes because it immobilizes Sr and Lns elements by forming solid solutions. The solution combustion synthesis, which is a self-sustaining oxi-reduction reaction between a nitrate and organic fuel, generates an exothermic reaction and that heat converts the precursors into their corresponding oxide products in air. The process has high energy efficiency, fast heating rates, short reaction times, and high compositional homogeneity. To confirm the combustion synthesis reaction, FT-IR analysis was conducted using glycine with a carboxyl group and an amine as fuel to observe its bonding with metal element in the nitrate. TG-DTA, X-ray diffraction analysis, SEM and EDS were performed to confirm the formed phases and morphology. Powders with an uncontrolled shape were obtained through a general oxide-route process, confirming hollandite powders with micro-sized soft agglomerates consisting of nano-sized primary particles can be prepared using these methods.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1366-1371
• /
• 2006

A structural coupling method is developed for the dynamic analysis of a nonlinear structure with concentrated nonlinear hinge joints or sliding lines. Component mode synthesis method is extended to couple substructures and the nonlinear models. In order to verify the improved coupling method, a numerical plate model consisting of two substructures and torsional springs, is synthesized by using the proposed method and its model parameters are compared with analysis data. Then the coupling method is applied to a three-substructure-model with the nonlinearity of sliding lines between the substructures. The coupled structural model is verified from its dynamic analysis. The analysis results show that the improved coupling method is adequate for the structural nonlinear analyses with the nonlinear hinge and sliding mode condition.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.5
• /
• pp.699-704
• /
• 2006

Escherichia coli RNase P is a ribonucleoprotein composed of M1 RNA and C5 protein. Previously, analysis of RNA aptamers selected for C5 protein from a synthetic RNA library showed that C5 protein could bind various RNA molecules as an RNA binding protein. In this study, we searched cellular RNA motifs that could be recognized by C5 protein by a genomic SELEX approach. We found various C5 protein-binding RNA motifs derived from E. coli genomic sequences. Our results suggest that C5 protein interacts with various cellular RNA species in addition to M1 RNA.

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.205-208
• /
• 1986

The synthesis of control structure involves the selection of controlled variable (or measured variable), and the structure interconnecting measured and manipulated variables (control loops). This paper deals with the synthesis job by using the structural analysis and block relative gain. This synthesis tool is very useful because they require minimal information, and the results show that this is a systematic and efficient metholodgy.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.2
• /
• pp.77-82
• /
• 1999

A sinusoidal model has been widely used in the analysis and synthesis of speech and audio signals, and becomes one of the efficient candidates for high quality low bit rate audio coders. One of the crucial steps in the analysis and synthesis using a sinusoidal model is the detection of tonal components. This paper proposes an efficient method for the analysis and synthesis of audio signals using a sinusoidal model, which uses psychoacoustic criteria such as masking effect, masking index, and JNDf(Just Noticeable Difference in Frequency). Simulation results show that the proposed method reduces the number of sinusoids significantly without degrading the quality of the synthesized audio signals.

• Journal of the Korean Ceramic Society
• /
• v.32 no.3
• /
• pp.341-348
• /
• 1995

An analysis of the use of temperature profiles in the determination of the kinetic parameters of combustion synthesis of Ti5Si3 were investigated. From profile analysis, an apparent activation energy of 12KJ/mol was calculated. The Maximum heating rate achieved during 10wt% Ti5Si3 reaction by the product dilution method was approximately $1.5\times$104 K/s. Coupling this value with the measured wave velocity of 7.02 cm/s yields a maximum thermal gradient of 2.14$\times$103 K/cm. The value of tr (=t*) was calculated to be 1.2$\times$10-1 s and the value of td (=tx) was calculated to be 32.89 s. Using the definition of t* and the measured wave velocity, the effective thermal diffusivity, $\alpha$, was calculated to be 0.59$\times$10 $\textrm{cm}^2$/s. From these analysis, the power function, G, was also calculated.

• Journal of KSNVE
• /
• v.5 no.4
• /
• pp.503-514
• /
• 1995

In the case of performing experimental modal analysis(EMA) and finite- element analysis(EFA) for a whole structure of automotive body that is composed of many complex parts, a trouble may arise from the calculation time, the capacity of memory in computers and the experimental conditions, etc. In this paper, for the vibrational analysis of automotive body model, the efficient modal synthesis method by means of dividing the whole structure into two parts and performing EMA and FEA for each part is studied. In addition, the method based on Lagrange interpolation is proposed for approximating rotational degrees-of-freedom information and linking FEA with EMA. In result, by measuring translational degrees-of-freedom information of only few points and adopting only few modes, the linking method based on Lagrange interpolation turned out to be efficient and accurate in the low frequency range.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.177-183
• /
• 2003

Vibration analysis using component mode synthesis method was carried out to identify that to some extent each component contributed to the whole vibration of a powertrain consisting of several components. This analysis helped decide the component to be modified to reduce the powertrain weight, without degrading its current vibration characteristics. As a result, a cylinder block was chosen as a redesign object. Topology optimization analysis was performed to design the topology of the cylinder block whose flange connected with the transmission was chosen to be the design domain. After all, a new prototype of cylinder block was manufactured based on the analysis results for the verification experiment. It was confirmed from the analytical and experimental results that u optimally designed cylinder block had an advantage over the current one in the powertrain weight, with the powertrain vibration characteristics improved slightly.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.501-504
• /
• 2001

The use of error compensation techniques has been recognized as an effective way in the improvement of the accuracy of a machine tool. The laser measurement method for identifying position errors of machine tool has the disadvantages such as high cost, long calibration time and usage of volumetric error synthesis model. Accordingly, this paper deals with analysis of the position errors of a machine tool using ball bar test without using complicated error synthesis model. Statistical analysis method was adopted in this paper for deriving position errors using hemispherical helix ball bar test.