• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.06a
• /
• pp.182-183
• /
• 2003

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.504-506
• /
• 1995

By means of adding B into Sendust alloy (Fe-Si-Al) with state of amorphous ribbon, mechnical properties of alloy was improved effectively, and magnetic properties didn't decrease obviously. The optimum adding quantity of B is 0.015-0.03 wt%. The adding of B was thought to give rise to reduction of ordering degree of $Fe_{3}(Si,Al)$ phase of Sedust alloy(Fe-Si-Al-B) and result in improvment of embrittlement of this alloy.

• Journal of the Korean Magnetics Society
• /
• v.17 no.6
• /
• pp.226-231
• /
• 2007

High frequency loss property of nanocrystalline amorphous ribbon with a high resistivity insulation layer of $TiO_2$ and $SiO_2$ was studied. The insulation layer was fabricated by sol-gel method using dip-coating. The optimum composition ratio of metal alkoxide and slurry for fabrication of insulation layer was established and insulation layer with high adhesion was coated on the nanocrystalline amorphous ribbon. Frequency loss of magnetic core material manufactured on nanocrystalline amorphous ribbon with the surface insulation layer decreased over 40 % compared with that of magnetic core material without surface insulation layer. The insertion loss of an inductive coupler, which was prepared by using magnetic core material coated insulation layer, decreased due to reduction of frequency loss for magnetic core material and insertion loss decreased in proportion to frequency.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.3
• /
• pp.432-436
• /
• 1994

The aging characteristics of amorphous FeS178TBS113TSiS19T wound cores have been investigated as a function of aging temperature and time. The core losses(1.2T/60Hz) of amorphous wound cores dipped in transformer oil decrease in comparision with initial stage of aging test due to insulation of ribbon stacks by oil penetration. It is estimated that it takes 30 years or more for 10% increase in core losses (1.2T/60Hz) of amorphous wound cores aged at normal transformer running temperature(100$^{\circ}C$). So we condlude that the amorphous core is satisfactorily applicable to transformer.

• Journal of Magnetics
• /
• v.15 no.4
• /
• pp.190-193
• /
• 2010

The design of joints in a transformer core significantly affects the transformer's efficiency. Air gaps cause variations in the flux distribution at the joints of the laminations, which depend on the geometry. Two similar samples consisting of electrical steel strips and amorphous ribbons were made. The spatial flux distributions were determined using an array of search coils for each sample. 2D models of these samples were created and examined by finite element analysis. The magnetic flux distribution for each lamination in the samples was computed. The results show that the flux density in amorphous ribbons above and below the air gap starts to approach saturation at lower flux density levels than for electrical steel. The flux density measured using the search coil under the air gap is increased in amorphous ribbons and decreased in the electrical steel with increasing frequency.

• Journal of Welding and Joining
• /
• v.17 no.4
• /
• pp.26-31
• /
• 1999

An attempt was made in this study to investigate the brazing characteristics of Zr-Be binary amorphous alloys for the development of a new brazing filler metal for joining Zircaloy-4 nuclear fuel cladding tubes. This study was also aimed at the feasibility study of rapidly solidified amorphous alloys to substitute the conventional physical vapor-deposited(PVD) metallic beryllium. The $Zr_{1-x}Be_{x}$($0.3\leq$x$\leq0.5$) binary amorphous alloys were produced in the ribbon form by the melt-spinning method. It was confirmed by x-ray diffraction that the ribbons were amorphous. The amorphous. the amorphous alloys were used to join bearing pads on Zircaloy-4 nuclear fuel cladding tubes. Using Zr-Be amorphous alloys as filler metals, it was found that the reduction in the tube wall thickness caused by erosion was prevented. Especially, in the case of using $Zr_{0.65}Be_{0.35}$ and $Zr_{0.7}Be_{0.3}$ amorphousalloys, the smooth and spherical primary $\alpha$-Zr particles appeared in the brazed layer, which was the most desirable microstructure from the corrosion-resistance standpoint.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.1
• /
• pp.67-72
• /
• 1991

For improving the magnetic properties of the amorphous Fe-B-Si alloy, we annealed the sample in a magnetic field oriented in the plane of the ribbon longitudinal to its long axis. By field annealing, coercive force and total core loss are reduced from 0.04 Oe to 0.02 Oe, and from 0.25 watt/kg to 0.15 watt/kg respectively in comparsion with non-field annealed specimen. These reductions were caused by the formation of 180 dcmain wall parallel to the annealing field due to the induced anisotropy.

• Korean Journal of Materials Research
• /
• v.1 no.3
• /
• pp.145-150
• /
• 1991

Crystallization and embrittlement of $Fe_{78}B_{13}Si_{9}$ amorphous alloy was investigated by differential scanning calorimetry, X-ray diffraction and transmission electron microscopy. The crystallization comprizes two exothermic processes. In the first crystallization stage, $\alpha$-(Fe, Si) dendrites are formed from the amorphous state, and in the second crystallization, $Fe_2B$ compounds are formed. An abrupt decrease of the fracture strain of the ribbon started from amorphous started annealed at about $340^{\circ}C$

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.12a
• /
• pp.244-244
• /
• 2003

• Proceedings of the Korean Magnestics Society Conference
• /
• 2004.12a
• /
• pp.89-90
• /
• 2004