• Membrane Journal
• /
• v.25 no.5
• /
• pp.447-455
• /
• 2015

In this study, Polysulfone (PSf) and polyetherimide (PEI) as the anion exchange polymers were aminated in the different ratio whereas the polyether ether ketone (PEEK) as the cation exchange polymer was sulfonated. The bipolar membranes of SPEEK (sulfonated PEEK)/APSf (aminated PSf) and SPEEK/APEI (aminated PEI) were prepared by the double-casting method. The surfaces of bipolar membranes were fluorinated in accordance with the amination ratio and applied to produce the hypochlorite. As the amination increased, the hypochlorite concentration is also increased. Typically, for SPEEK/APSf 3 : 1 membrane, the produced hypochlorite concentration was 61.0 ppm and its durability was 220 min for the non-fluorinated membrane while for the fluorinated membrane, the concentration of 58.6 ppm and its durability lasted 570 min. Also for SPEEK/APEI 3 : 1 membrane, the hypochlorite concentrations of 60.1 ppm and 58.3 ppm for before- and after-fluorination, respectively were observed whereas the durability was remarkably developed from 150 min to 440 min. Therefore, the surface fluorination takes an important role for the development of the membrane durability.

• Membrane and Water Treatment
• /
• v.7 no.1
• /
• pp.39-53
• /
• 2016

In this study, polysufone (PSf) was used as a base polymer to synthesize sulfonated polysulfone (SPSf) and aminated polysulfone (APSf) as cation and anion exchange polymers, respectively. Then the ion exchange polymers were coated onto the surface of commercial carbon electrodes. To compare the capacitive deionization (CDI) and membrane capacitive deionization (MCDI) processes, the pristine carbon electrodes and ionic polymer coated electrodes were tested under various operating conditions such as feed flow rate, adsorption time at fixed desorption time, and feed concentration, etc., in terms of effluent concentration and salt removal efficiency. The MCDI was confirmed to be superior to the CDI process. The performance of MCDI was 2-3 times higher than that of CDI. In particular, the reverse desorption potential was a lot better than zero potential. Typically, the salt removal efficiency 100% for 100 mg/L NaCl was obtained for MCDI at feed flow rate of 15 ml/min and adsorption/desorption time of 3 min/1 min and applied voltages 1.0 V for adsorption and -0.3 V for desorption process, and for 500 mg/L, the salt removal efficiency 91% was observed.

• Membrane and Water Treatment
• /
• v.6 no.1
• /
• pp.27-42
• /
• 2015

In this study, poly (phenylene oxide) (PPO) and poysulfone (PSf) were sulfonated and aminated respectively. Both sulfonated poly (phenylene oxide) (SPPO) and aminated polysulfone (APSf) were characterized via the measurement of FT-IR, swelling degree, ion exchange capacity (IEC), and ion conductivity. Then the surfaces of these membranes were modified by surface fluorination using 2000 ppm $F_2$ gas against $N_2$ gas for 1 h at room temperature. The surface fluorinated SPPO and APSf membranes were characterized again to determine any differences between the pristine and fluorinated membranes. In total, 3 types of bi-polar membranes were prepared by varying the IEC of the APSf and having a fixed value for the IEC of the SPPO. The hypochlorite concentration generated by using the surface fluorinated membranes was dependent on the IEC of the APSf and ranged from 683 to 826 ppm, while there was a considerable improvement in the durability of the surface fluorinated membranes as they remained intact even after operating for 4 h.

• Membrane Journal
• /
• v.27 no.5
• /
• pp.449-457
• /
• 2017

In this study, the 10 stages stacked module was designed by increasing the number of unit cells in the membrane capacitive deionization(MCDI) process. The aminated polysulfone and sulfonated poly(ether ether ketone) were synthesized and coated on porous carbon electrode by casting method. The salt removal efficiency was measured for the 10 stage stacked module under the operation conditions of adsorption voltage and time, desorption voltage and time, flow rate and concentration of feed water, and di-valent solutions including $CaSO_4$, $MgCl_2$ and tap water. Typically, when 100 mg/L of NaCl as the feed was used, the salt removal efficiency was 98.3% at a flow rate of 100 mL/min, the adsorption condition of 1.2 V/3 min and desorption condition of -0.5 V/5 min.