• BMB Reports
• /
• v.30 no.5
• /
• pp.346-351
• /
• 1997

The maximum adsorption/desorption conditions and the adsorption mechanism of globular proteins to vaccine adjuvants were determined. The maximum adsorption ratio of protein to the $Al^{3+}$ content of aluminum oxyhydroxide and the optimal adsorption pH are 2:1 (${\mu}g:{\mu}g$) for bovine serum albumin (BSA) at pH 6.0 and 2.5:1 (${\mu}g:{\mu}g$) for immunoglobulin G (IgG) at pH 7.0, respectively. The maximum adsorption ratio onto aluminum phosphate gel was 1.5:1 (${\mu}g$ Protein:${\mu}g$ $Al^{3+}$) at pH 5.0 for both BSA and IgG. Adsorption of the native globular proteins, BSA and IgG, to aluminum oxyhydroxide and aluminum phosphate gel was reversible as a function of pH. Complete desorption of these proteins from aluminum phosphate gel was observed at alkaline pH, whereas only 80~90% removal from aluminum oxyhydroxide was achieved with alkaline pH and 50 mM phosphate buffer. We conclude that electrostatic and hydrogen bonding interactions between the native proteins and adjuvants are important binding mechanisms for adsorption, and that the surface charge of the protein and the colloid components control the maximum adsorption conditions.

• YAKHAK HOEJI
• /
• v.35 no.4
• /
• pp.319-325
• /
• 1991

Aluminum phosphate gel was synthesized by reacting aluminum sulfate as a soluble aluminum salt to tribasic sodium phosphate in this study. The optimal synthesis conditions based on the yield of product were investigated by applying Box-Wilson experimental design. It was found that optimal synthesis conditions were as follows: Reaction temperature; $61~71^{\circ}C$, concentration of two reactants; 12.27~13.83%, concentration ratio of two reactants; [AI$_{2}$(SO$_{4}$)$_{3}$]/[Na$_{3}$PO$_{4}$]= 0.5, reaction time; 10.9~12.1 minutes, drying temperature of product; $60~72^{\circ}C$. Aluminum phosphate gel prepared by the optimal synthesis conditions was suspended with four types of natural and synthetic gums at the concentration of 0.375~1.5wv%. Their Theological properties of aluminum phosphate gels were examined with Haake-Rotovisco RV 20 rotational viscometer. It showed that the higher concentration of suspending agents and lower temperature, the higher viscosity. Aluminum phosphate gel suspended by pectin and agar showed plastic flow with rheopexy, and their gels suspended by sodium alginate and sod. CMC showed plastic flow with thixotropy.

• YAKHAK HOEJI
• /
• v.27 no.2
• /
• pp.139-148
• /
• 1983

The neutralizing capacities of the antacids, which are frequently used in Korean market, were evaluated in vitro by the methods of Resset and Rice, Fordtran and Collyns, and modified Beekman, respectively. The antacids used in the study are two kinds, the one is preparations from Seoul National University Hospital and the other is products from pharmaceutical companies, and their components are aluminum phosphate, aluminum hydroxide, magnesium aluminum hydroxide, magnesium hydroxide, basic aluminum sucrose sulfate and $2MgO{\times}Al_{2}O_{3}{\times}SiO_{3}$, etc. The hospital preparations, DMC and MAC powders, showed most powerful and sustained neutralizing capacities, i.e. they maintained the pH range from 5 to 8 for 60min, Whereas pharmaceutical products, aluminum hydroxide gel containing magnesium hydroxide and magnesium aluminum hydroxide gel exhibited a moderate capacities, i.e pH ranged from 3 to 6, and aluminum phosphate, $2MgO{\times}Al_{2}O_{3}{\times}SiO_{2}$ and basic aluminum sucrose sulfate displayed a weak activity, pH ranged from 2 to 3. When the therapeutic doses of aluminum hydroxide gel containing magnesium hydroxide and magnesium aluminum hydroxide gel were divided into 2 doses and each dose was used at the interval of 30min., the divided doses kept more prolonged higher pH than the single therapeutic dose. Milliequivalents of neutralizing capacities of each antacid were measured by the method of Fordtran and Collyns. The milliequivalents per 1ml of aluminum hydroxide gel, aluminum hydroxide gel containing magnesium hydroxide, magnesium aluminum hydroxide gel and aluminum phosphate were 2.87, 2.86, 2.57, and 0.67, respectively. The milliequivalents per 100mg of preparations, i.e. MAC powder, dried aluminum hydroxidgel, DMC powder, 2MgO, $Al_{2}O_{3}$. $SiO_{2}$, magnesium aluminum hydroxide and basic aluminum sucrose sulfate were 1.91, 1.68 1.63, 1.45, 1.44, and 0.44, respectively.

• Journal of the Korean Ceramic Society
• /
• v.41 no.8
• /
• pp.610-617
• /
• 2004

For preparation $\alpha$-Al$_2$O$_3$ platelets having 20 $\mu$m in average diameter and 0.2∼0.3 $\mu$m in thickness, we have prepared aluminum hydroxides gel by using aluminum sulfate and sodium sulfate as starting materials. In this study, we investigated the effect of the amount of sodium phosphate on particle size, morphology and thickness of $\alpha$-Al$_2$O$_3$ platelets. When sodium phosphate was not added to aluminum hydroxides gel, most of $\alpha$-Al$_2$O$_3$ platelets had hexagonal shape but the thickness was over 1.0 $\mu$m, and this sample was not adequate for pearlescent pigment. On the other hand, introduction of sodium phosphate caused an increase of aspect ratio (particle diameter/thickness) with a decrease in $\alpha$-Al$_2$O$_3$ platelet thickness.

• Corrosion Science and Technology
• /
• v.17 no.1
• /
• pp.30-36
• /
• 2018

The high rate of corrosion of magnesium alloys makes it limited for industrial applications. Therefore, surface treatment is required to enhance their corrosion resistance. In our study, a chemical conversion coating for protecting the corrosion of the magnesium alloy, AZ31B, was prepared by using a phosphate-permanganate solution. The chemical conversion coating had a limited protection ability due to defects arising from cracks and pores in the coating layer. The sol-gel coating was prepared by using trimethoxymethylsilane (MTMS) and 3-glycidoxypropyltrimethoxysilane (GPTMS) as precursors, and aluminum acetyl acetonate as a ring opening agent. The corrosion protection properties of sol-gel and conversion coatings in 0.35wt% NaCl solution were measured by the electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization test. The EIS results indicated that the resistance of the chemical conversion coating with the sol-gel coating was significantly improved through the sol-gel sealed phosphate-permanganate conversion coating. The results of the potentiodynamic polarization test revealed that the sol-gel coating decreased the corrosion current density ($I_{corr}$). The SEM image showed that the sol-gel coating sealed conversion coating and improved corrosion protection.

• Corrosion Science and Technology
• /
• v.20 no.4
• /
• pp.175-182
• /
• 2021

Magnesium alloy is limited in the industrial field because its standard electrode potential is -2.363 V vs. NHE (Normal Hydrogen Electrode) at 25 ℃. This high electrochemical activity causes magnesium to quickly corrode with oxygen in air; chemical conversion coating prevents corrosion but causes surface defects like cracks and pores. We have examined the anti-corrosion effect of sol-gel coating sealed on the defected conversion coating layer. Sol-gel coatings produced higher voltage current and smaller pore than the chemical conversion coating layer. The conversion coating on magnesium alloy AZ31 was prepared using phosphate-permanganate solution. The sol-gel coating was designed using trimethoxymethylsilane (MTMS) and (3-Glycidyloxypropyl) trimethoxysilane (GPTMS) as precursors, and aluminum acetylacetonate as a ring-opening agent. The thermal shock resistance was tested by exposing specimens at 140 ℃ in a convection oven; the results showed changes in the magnesium alloy AZ31 surface, such as oxidization and cracking. Scanning electron microscope (FE-SEM) analysis confirmed a sealed sol-gel coating layer on magnesium alloy AZ31. Electrochemical impedance spectroscopy (EIS) measured the differences in corrosion protection properties by sol-gel and conversion coatings in 0.35 wt% NaCl solution, and the potentiodynamic polarization test and confirmed conversion coating with the sol-gel coating show significantly improved resistance by crack sealing.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.1
• /
• pp.51-61
• /
• 2010

Ettringite $(Ca_6[Al(OH)_6]_2(SO_4)_3{\cdot}26H_2O)$ is a sulfate mineral that shows a complicate property in concrete. It is often called as "a cancer of concrete" because secondary ettringite formation in hardened concrete often cause expansion and cracking of concrete due to its expansive crystal structure. In the present study, we tested the possibility for crystal growth inhibition of secondary ettringite by crystallization inhibitors that are commercially used for scaling inhibitors in Korea. For the test, we developed a method of ettringite solution synthesis. Three types of crystallization inhibitors were selected and examined the effects On ettringite growth inhibition. The experimental results of ettringite solution synthesis indicated that ettringite was successfully synthesized under condition that the mass balance between calcium hydroxide saturated solution and aluminum sulfate solution was attained. Monosulfate and semisulfate were synthesized when the ratio of $Ca^{2+}$ ions to ${SO_4}^{2+}$ ions was increased. The induction time of ettringite crystallization was less than 2 min. and crystallization was almost completed within an hour. The experimental results of ettringite crystallization inhibition showed that organic PBCT (2-Phosphonobutane-1,2,4-Tricarboxylic Acid) and inorganic SHMP (Sodium Hexametaphosphate) were relatively less effective on ettringite crystallization inhibition under experimental conditions. However, organic HEDP (1-Hydoxyethylidene-1,1-Diphosphonic Acid) effectively prevented ettringite growth with producing amorphous gel phase materials up to inhibitor concentration 0.1 vol.% of aluminum sulfate solution.