• 한국산업융합학회 논문집
• /
• 제9권2호
• /
• pp.141-145
• /
• 2006

In case of sense case manufactured by method of outage capacity, sensitivity is declined by outside effect and method of the photo electricity has a problem in transmission. therefore, packing case of composite sense should be developed to improve such a problem about influence of outside environment and its property evaluation has been performed. Mechanical property and result of analysis & test evaluation of Mat'l on aluminum die-casting(ADC 12type) Mat'l developed are as following. Tensile test piece, No. 4 of KS B 0801, has been applied to mechanical property test of Mat'l and It has been tested by method of metal mat'l tensile test(KS B 0802 : 2003). It can be found that physical property to KS(Korea Standard) is excellent. and homogeneous mechanical property appears. Test of Mat'l analysis has been performed by using OE Spectrometer, according to ASTM E 1251 : 1994 regulation. Consequently, good and homogeneous component contents classified by element to standard, except for Fe, have been obtained with coordination of Fe content as below 1.3% from composition standard of Aluminum Die-casting.

• 한국표면공학회지
• /
• 제20권4호
• /
• pp.144-153
• /
• 1987

In the case of dipping the Ni-Resist cast iron into molten aluminum with iron content, the thickness of intermetallic compound was remarkably increased with increasing iron content. The thickness was shown by following equation in the range of 1-3% iron content; $x=22.5t^{1/2}+4.47{\cdot}t{\cdot}(Fe%)$. where, x is thickness(${\mu}m$), t the time (minute), Fe% the iron w/o. When the Ni-Resist cast iron was dipped into the molten aluminum containing zinc content, the intermetallic compound thickness was also increased with increasing zinc contents. And thickness was represented by the following equation in the range of 2-10% zinc content; $x=3.46t^{1/2}+0.27{\cdot}t{\cdot}(Zn%)$. However, in the case of dipping the Ni-resist cast iron into molten aluminum with silicon content, the thickness of intermetallic compound was decreased with increasing silicon content, as shown in the following equation; $x=7.17t^{1/2}-0.15{\cdot}t{\cdot}(Si%)$. The intermetallic compound formed onto Ni-Resist cast iron was identified to be $FeAl_3\;and\;Fe_3Al$. As the result of hardness measurement, the peak hardness appeared in the intermetallic compound at near interface of the cast iron and the compound.

• 공학기술논문지
• /
• 제11권4호
• /
• pp.227-235
• /
• 2018

Studies on the laser cutting processing characteristics of magnesium alloys can be divided into three parts, comparing the cutting faces of magnesium alloy and aluminum alloy, observing the shape of the corner where straight lines meet, and observing the straight lines and arcs. First, there were no laser cutting conditions for magnesium alloys, so it was observed to cut magnesium alloy and aluminum alloy under the same processing conditions as aluminum alloy to shape and surface of the cut surface. Next, to observe the characteristics of the corner, we observed the shape of the corner according to the angle change of the part where the two lines meet, and finally we observed various angles to observe the characteristics of the part where the arc meets the line. Finally, laser cutting processing characteristics of magnesium alloys and aluminum alloys obtained based on the above study contents were summarized.

• 한국재료학회지
• /
• 제32권9호
• /
• pp.361-368
• /
• 2022

The overall process, from the pre-treatment of aluminum substrates to the eco-friendly neutral electroless Ni-P plating process, was observed, compared, and analysed. To remove the surface oxide layer on the aluminum substrate and aid Ni-P plating, a zincation process was carried out. After the second zincation treatment, it was confirmed that a mostly uniform Zn layer was formed and the surface oxide of aluminum was also removed. The Ni-P electroless plating films were formed on the secondary zincated aluminum substrate using electroless plating solutions of pH 4.5 and neutral pH 7.0, respectively, while changing the plating bath temperature. When a neutral pH7.0 electroless solution was used, the Ni-P plating layer was uniformly formed even at the plating bath temperature of 50 ℃, and the plating speed was remarkably increased as the bath temperature was increased. On the other hand, when a pH 4.5 Ni-P electroless solution was used, a Ni-P plating film was not formed at a plating bath temperature of 50 ℃, and the plating speed was very slow compared to pH 7.0, although plating speed increased with increasing bath temperature. In the P contents, the P concentration of the neutral pH 7.0 Ni-P electroless plating layer was reduced by ~ 42.3 % compared to pH 4.5. Structurally, all of the Ni-P electroless plating layers formed in the pH 4.5 solution and the neutral (pH 7.0) solution had an amorphous crystal structure, as a Ni-P compound, regardless of the plating bath temperature.

• 한국기계가공학회지
• /
• 제21권2호
• /
• pp.109-115
• /
• 2022

The demand for metal 3D printing technology is increasing in various industries. The materials commonly used for metal 3D printing include aluminum alloys, titanium alloys, and stainless steel. In particular, for applications in the aviation and defense industry, aluminum alloy 3D printing parts are being produced. To improve the corrosion resistance in the 3D printed aluminum alloy outputs, a post-treatment process, such as chromate coating, should be applied. However, powdered materials, such as AlSi7Mg and AlSi10Mg, used for 3D printing, have a high silicon content; therefore, a suitable pretreatment is required for chromate coating. In the desmut step of the pretreatment process, the chromate coating can be formed only when a smut composed of silicon compounds or oxides is effectively removed. In this study, suitable desmut solutions for 3D printed AlSi7Mg and AlSi10Mg materials with high silicon contents were presented, and the chromate coating properties were studied accordingly. The smut removal effect was confirmed using an aqueous desmut solution composed of sulfuric, nitric, and hydrofluoric acids. Thus, a chromate coating was successfully formed. The surfaces of the aluminum alloys after desmut and chromate coating were analyzed using SEM and EDS.

• 원예과학기술지
• /
• 제33권2호
• /
• pp.227-232
• /
• 2015

수출용 스프레이 장미 차광방법(차광률 50%와 70% 알루미늄 차광 전용 스크린 및 부직포)에 따른 고온기 기상환경, 절화품질 및 생산성을 조사하였다. 차광방법에 따른 일일 최고와 적산 일사량은 부직포보다 알루미늄 전용 차광에서 높았고, 70%보다 50% 차광처리에서 더 높았다. 대기온도 및 근권 온도는 부직포보다 알루미늄 전용 차광에서 낮았고, 차광률 70%에서 더 낮은 경향이었으며, 대기습도는 처리 간 차이가 없었다. 엽온과 엽록소 함량(SPAD)은 알루미늄 차광, 특히 50% 차광처리에서 약간 더 높았다. 차광방법별 상품수량 및 수출가능 수량은 'Lovely Lydia'를 제외한 시험품종 모두가 알루미늄 차광처리에서 높았으며, 특히 50% 차광처리에서 더 높았다. 절화장, 경경 및 마디 수, 7매 엽수, 소화수 및 소화폭도 알루미늄 차광처리에서 우수하였다. 절화장의 경우는 50%보다 70% 알루미늄 차광처리에서 더 우수한 경향이었다. 꽃잎 색도의 경우 부직포 차광보다 알루미늄 차광처리에서 a, b값이 증가하였고, 절화 수명도 품종에 따라 0.5-2.5일 더 길었다.

• 한국환경과학회지
• /
• 제19권11호
• /
• pp.1385-1390
• /
• 2010

Repeated additions of untreated slurry to soil affected ecology and caused high levels of heavy metal in soil and ground water. The objective of this study was to evaluate heavy metal from hanwoo slurry with ferrous sulfate ($FeSO_4{\cdot}7H_2O$), aluminum sulfate [$Al_2(SO_4)_3{\cdot}14H_2O$, alum] and aluminum chloride ($AlCl_3{\cdot}6H_2O$) as a way to improve environmental management in hanwoo industry. The treatment rates, which were incorporated totally within the hanwoo slurry, were 1.0 g and 1.5 g of ferrous sulfate, alum and aluminum chloride/25 g of hanwoo slurry. The various rates of chemical additives significantly increased dry matter (9.98~13.94%) and decreased pH (3.48~6.52) compared with the controls. The use of chemical additives decreased Fe (11~29%), Al (7~12%), Zn (13~36%), and Cu (4~32%) contents, except for Fe in hanwoo slurry with ferrous sulfate and Al in hanwoo slurry with alum and aluminum chloride. In addition, the reduction in heavy metal should be associated with reduction in pH. In conclusion, the results of this study suggest that alum and aluminum chloride additives at rate of 1.5 g were cost-effective management practice that significantly reduces heavy metal from hanwoo slurry, while it may be improved environmental management.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.489-494
• /
• 2017

본 연구에서는 마이크로 크기의 알루미늄 함유량에 따른 파라핀/알루미늄 연료의 연소특성 변화를 연구하였다. 마이크로 알루미늄 입자 첨가량에 따른 연소 특성을 파악하기 위해 순수 파라핀 왁스에 5 wt%, 10 wt%의 마이크로 알루미늄 입자를 혼합하여 연소 실험을 수행하였다. 연료는 평균 $8{\mu}m$ 크기의 알루미늄 입자와 Sasol사의 미정질 파라핀 왁스(Sasol 0907)를 이용하였고, 산화제는 기체산소를 적용하여 고체연료의 후퇴율과 압력선도, 연소효율의 변화 등을 조사하였다. 알루미늄 입자의 함량이 높을수록 고체연료의 후퇴율과 연소실 압력 및 연소 성능효율이 모두 증가함을 확인하였으나 증가폭은 미미함을 확인하였다.

• 한국초지조사료학회지
• /
• 제34권4호
• /
• pp.262-268
• /
• 2014

In order to reveal the aluminum (Al) stress tolerance mechanisms in alfalfa plant at low pH soil, a proteomic approach has been conducted. Alfalfa plants were exposed to Al stress for 5 days. The plant growth and total chlorophyll content are greatly affected by Al stress. The malondialdehyde (MDA) and $H_2O_2$ contents were increased in a low amount but free proline and soluble sugar contents, and the DPPH-radical scavenging activity were highly increased. These results indicate that antioxidant activity (DPPH activity) and osmoprotectants (proline and sugar) may involve in ROS ($H_2O_2$) homeostasis under Al stress. In proteomic analysis, over 500 protein spots were detected by 2-dimentional gel electrophoresis analysis. Total 17 Al stress-induced proteins were identified, of which 8 protein spots were up-regulated and 9 were down-regulated. The differential expression patterns of protein spots were selected and analyzed by the peptide mass fingerprinting (PMF) using MALDI-TOF MS analysis. Three protein spots corresponding to Rubisco were significantly down-regulated whereas peroxiredoxin and glutamine synthetase were up-regulated in response to Al stress. The different regulation patterns of identified proteins were involved in energy metabolism and antioxidant / ROS detoxification during Al stress in alfalfa. Taken together, these results provide new insight to understand the molecular mechanisms of alfalfa plant in terms of Al stress tolerance.

• 한국콘텐츠학회논문지
• /
• 제14권2호
• /
• pp.457-466
• /
• 2014

고 에너지 전자선 치료에 있어서 차폐물질은 종양조직 외 정상조직이나 주요장기를 보호하기 위해 사용된다. 하지만 이러한 물질에서 발생되어지는 산란선은 심부선량에 영향을 줄 수 있으며, 물질원자번호에 따라 다르게 나타난다. 이에 차폐물질로써 사용가능한 알루미늄, 구리, 납 등의 다양한 원자번호 물질을 전하 감약율 95% 되는 두께로 하여 측정과 MCNPX 모의계산으로 산란율을 비교분석하였다. 산란선 영향을 많이 받는 표면의 선량변화율은 최대 물질두께에서 +0.88%, 원자번호에서 +0.43%의 영향을 받으며, 전하 감약율 95% 되는 두께의 알루미늄, 구리, 납 물질은 측정에서 +19.70%, +15.20%, +12.40% 계산에서 +25.00%, +15.10%, +13.70%를 보였다. 이로 인해 산란율은 물질두께가 원자번호보다 많은 영향을 주며, 산란전자가 광자보다 많은 기여를 하고 있음을 알 수 있었다. 이에 임상에서의 적절한 차폐물질은 두께영향 산란선이 적게 방출되는 고 원자번호물질이 적당하다고 사료된다.