• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.1
• /
• pp.1-7
• /
• 1999

In order to determine the mode I stress intensity factor ($K_I$) by means of the alternating current potential drop(ACPD) technique, the change in potential drop due to load for a paramagnetic material containing a two-dimensional surface crack was examined. The cause of the change in potential drop and the effects of the magnetic flux and the demagnetization on the change in potential drop were clarified by using the measuring systems with and without removing the magnetic flux from the circumference of the specimen. The change in potential drop was linearly decreased with increasing the tensile load and was caused by the change in conductivity near the crack tip. The reason of decreasing the change in potential drop with increasing the tensile load was that the increase of the conductivity near the crack tip due to the tensile load caused the decreases of the resistance and internal inductance of the specimen The relationship between the change in potential drop and the change in $K_I$ was not affected by demagnetization and was independent of the crack length.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.6
• /
• pp.211-215
• /
• 2003

Alternating current (AC) losses of two Bi-2223 ([Bi, Pb] : Sr : Ca : Cu :O = 2:2:2:3) tapes [one untwisted (Tape I, twist-pitch of $\infty$ mm) and the other with a twist-pitch of 8mm (Tape II) ] were measured and compared. These samples, produced by the powder-in-tube (PIT) method, are multi-filamentary and have a Ag/Au and Ag matrix, respectively. Susceptibility measurements were conducted while cooling in a magnetic field. Flux loss measurements were conducted as a function of ramping rate, frequency and field direction. The AC flux loss increases as the twist-pitch of the tapes decreased, in agreement with the Norris Equation.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.97-102
• /
• 2017

A current transformer (CT) is a type of sensor that consists of a combination of electric and magnetic circuits, and it measures large ac currents. When a large amount of current flows into the primary winding, the alternating magnetic flux in the iron core induces an electromotive force in the secondary winding. The characteristics of a CT are determined by the iron core design because the iron core is saturated above a certain magnetic flux density. In particular, when a large current, such as a current surge, is input into a CT, the iron core becomes saturated and the induced electromotive force in the secondary winding fluctuates severely. Under these conditions, the CT no longer functions as a sensor. In this study, the characteristics of the secondary winding were investigated using the time-difference finite element method when a current surge was provided as an input. The CT was modeled as a two-dimensional analysis object using constraints, and the saturation characteristics of the iron core were evaluated using the Newton-Rhapson method. The results of the calculation were compared with the experimental data. The results of this study will prove useful in the designs of the iron core and the windings of CTs.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.9
• /
• pp.1269-1274
• /
• 2012

In this paper, the iron loss was calculated using estimated iron loss coefficient at 650W Interior Permanent Magnet Synchronous Motor(IPMSM) and 250W IPMSM. The iron loss coefficients was estimated different according to electrical steel material used to stator and rotor core in motor. Aspect of The rotating flux field and alternating flux field was confirmed by magnetic field behavior and harmonic analysis in stator core, the iron loss was calculated using flux density by Finite Element Method(FEM) and estimated coefficients by iron loss coefficient estimation proposed in this paper. The iron loss experiment was performed for verified to iron loss calculation, and the iron loss coefficients were verified by comparison of iron loss calculation value and experimental value.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.1
• /
• pp.8-15
• /
• 1999

In order to develop an effective way of measuring the mode I stress intensity factor, $K_I$, by the technique based on the alternating current potential drop (ACPD), the effect of the magnetic flux in the air on the change in potential drop due to load for both ferromagnetic and paramagnetic materials containing a two-dimensional surface crack was investigated. Additionally the effects of the demagnetization and the crack length on the change in potential drop were examined. In the case that the measuring system was designed to induce a large amount of electromotive force, the amount of the change in potential drop due to load was shown to increase largely Also the relationship between the change in potential drop and that in $K_I$ was indicated to be linear without any treatment and it was shown that the demagnetization had almost no effect on the change in potential drop. The change in potential drop did not depend on the crack length but on the measuring system. For the application of the ACPD technique to determine $K_I$.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.133-136
• /
• 2006

전기강판으로 제작된 전기기기의 보다 정확한 수치적인 해석을 위해서는 회전자계(Rotating m-agnetic flux)에 따른 전기강판의 정확한 자계특성 측정이 필요하다. 본 논문에서는 개발된 2방향 자계인가 형 Single sheet tester를 이용하여 회전자계에 따른 전기강판의 자계특성을 측정하였다. 실험을 통하여 등방성 시료와 이방성 시료에 대하여 각각 회전자계 및 교번, 회전자계의 혼합형 자계를 인가하여 1.6[T]와 1.2[T]까지 측정할 수 있었으며, 일반적인 철손(Alternating Iron Loss)외에 회전자계 인가 시에 B와 H의 위상차이에 의해 발생하는 회전자계 손실을 측정하였다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.1
• /
• pp.54-61
• /
• 2000

In order to determine the mode I stress intensity factor ($K_I$) by means of the alternating current potential drop(ACPD) technique, the change in potential drop due to load for a paramagnetic material containing a two-dimensional surface crack was examined. The cause of the change in potential drop and the effects of the magnetic flux and the demagnetization on the change in potential drop were clarified by using the measuring systems with and without removing the magnetic flux from the circumference of the specimen. The change in potential drop was linearly decreased with increasing the tensile load and was caused by the change in conductivity near the crack tip. The reason of decreasing the change in potential drop with increasing the tensile load was that the increase of the conductivity near the crack tip due to the tensile load caused the decreases of the resistance and internal inductance of the specimen. The relationship between the change in potential drop and the change in $K_I$ was not affected by demagnetization and was independent of the crack length.

• Journal of Korea Foundry Society
• /
• v.26 no.5
• /
• pp.205-210
• /
• 2006

The structural control of Al-Si alloy, which was not studied among various electromagnetic processing of materials, was considered applying the alternating current and direct current magnetic flux density. The main aim of the present study is to investigate the effects of electromagnetic vibration on the macro and microstructure of Al-Si alloy in order to develop a new process of structural control in Al-Si alloy. When the electromagnetic vibration is conducted for changing the shape of primary aluminum, at low frequency(>60Hz), the shape of dendrite is changed speroidal shape. When the electromagnetic vibration is conducted for changing the shape of eutectic silicon, the fact that a morphological change of the eutectic silicon from coarse platelet flakes to fine fiber shape is observed and the improvement of the mechanical properties is achieved with EMV (Electro Magnetic Vibration) process at high frequency(>500Hz).

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.5
• /
• pp.552-559
• /
• 2011

Recently, the eddy current testing(ECT), alternating current field testing, magnetic flux leakage testing and remote field testing have been used as a nondestructive evaluation method based on the electromagnetic induction phenomenon. The eddy current testing is now widely accepted as a NDE method for the heat exchanger tube in the electric power industry, chemical, shipbuilding, and military. The ECT system mainly consists of the synthesizer module, analog module, analog-to-digital converter, power supplier, and data acquisition and analysis program. In the previous study, the synthesizer module and the analog module which is essential to the ECT system were primarily developed, and in this study the data acquisition and analysis program were developed. The operation system for this program is based on the Windows 7, and optimized for the Korean users, and the specific feature of this program using setup wizard enables inspector to make a setup easily for acquisition and analysis of ECT data. In this paper, the configuration and functions of eddy current data acquisition and analysis program will be introduced.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.2
• /
• pp.155-161
• /
• 2010

Recently, the electromagnetic techniques of the eddy current testing(ECT), alternating current field testing, magnetic flux leakage testing and remote field testing have been used as a nondestructive evaluation method based on the electromagnetic induction. The eddy current testing is now widely accepted as a NDE method for the heat exchanger tube in the electric power industry, chemical, shipbuilding, and military. The ECT system mainly consists of the synthesizer module, analog module, analog-to-digital converter, power supplier, and data acquisition and analysis program. In this study, the synthesizer module and the analog module which are essential to the ECT system were primarily developed. The developed ECT system is basically a multifrequency type which is able to inject the maximum four frequencies based on the frequency and time domain multiplexing method. Conclusively, we confirmed that the EC signal was processed appropriately in each circuit modules, and the Lissajous EC signal was displayed in the impedance plane.