• The Journal of Engineering Geology
• /
• v.31 no.1
• /
• pp.67-81
• /
• 2021

Grouting is used for reinforcement and waterproofing of soft ground to increase its bearing capacity, reduce the impacts of rising or lowering groundwater levels, and reduce subsidence due to vibration and general causes. This study investigated the enhancement of grout strength and hardening time by the addition of reinforcing fibers, and the development of non-cement grouting materials from blast furnace slag. An experiment was performed to measure the increase in grout strength resulting from the addition of 0.5% increments of aramid and carbon reinforcing fibers. The results show that the uniaxial compressive strength of grout increases with increasing content of reinforcing fiber. Comparison of three admixtures of finely powdered blast furnace slag and 10%, 20%, and 30% calcium hydroxide stimulating agent showed that the uniaxial compressive strength of the mixture increases with increasing content of alkaline stimulant; however, the strength was lower than for 100% pure cement. The reaction of calcium hydroxide with blast furnace slag powder, which increases the strength of the grout, is more effective if injected as a solution rather than a powder.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.3
• /
• pp.102-109
• /
• 2011

In this study, in order to develop ultra rapid hardening mortar(URHM) for tunnel repairs using bottom ash of low recycle ratio and Admixture as Eco concept, watertightness and durability properties of URHM on temperature condition of construction field were performed. Test result, seepage quantity and water absorption coefficient regarding watertightness of URHM were as in the following : series II > series I. Seepage quantity for the standard condition were smaller than low temperatures. all specimens were satisfied below 20g as standards of seepage quantity on KS F 4042. Because of the decrease of unit cement content by to replacement of blast furnace slag, the neutrlization resistance for durability properties was reduced. The result of alkali resistance and acide resistance, compressive strengths for specimens soaked in calcium hydroxide solution of seriesI were lower than compressive strengths for specimens not soaked. On the other hand, the case of series II show that the deterioration of compressive strengths for specimens was not almost showed. Compressive strengths of specimens soaked were similar with specimens not soaked except series II-C in $5^{\circ}C$. Therefore, specimens using both blast furnace slag and bottom ash were good in alkali resistance and acide resistance.

• Journal of the Korea Concrete Institute
• /
• v.28 no.5
• /
• pp.593-600
• /
• 2016

The paper presented investigates the effects of kaolinite on strength properties of alkali-activated multi-component cement. The binders of this study was blended of ground granulated blast furnace slag (GGBFS), fly ash (FA), silica fume (SF) and kaolinite (KA). In this study, the specimens of combination of 20%~70% GGBFS, 10%~60% FA, 10% SF (constant ratio) and 10%~50% KA binder were used for strength properties tests. The water/binder ratio was 0.5. The binders (GGBFS + FA + SF + KA) was activated by sodium hydroxide (NaOH) and sodium silicate ($Na_2SiO_3$) was 10% by total binder weight (10% NaOH + 10% $Na_2SiO_3$). The research carried out is on the compressive strength, water absorption, ultrasonic pulse velocity (UPV) and X-ray diffraction (XRD). The compressive strength decreased as the contents of KA increase. One of the major reason for this is the low reactivity of KA compared with other raw materials used as precursors such as GGBFS or FA. The presence of remaining KA indicates that the initially used quantity has not fully reacted during hydration. Moreover, the results have indicated that increased of KA contents decreased UPV under all experimental conditions. The drying shrinkage and water absorption increased as the content of KA increase. Test result clearly showed that the strength development of multi-component blended cement were significantly dependent on the content of KA and GGBFS.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.2
• /
• pp.1-30
• /
• 1981

To investigate the formation of the chromophoric structures taking place during the alkaline pulping vanillyl alcohol [${\alpha}-^{13}C$] guaiacylglycerol-${\beta}$-aryl ether [${\alpha}-^{13}C$ or ${\gamma}-^{13}C$] and phenylcoumarn [${\alpha}-^{13}C$] units as model lignins were treated with 1N sodium hydroxide at 165$^{\circ}C$ for 1.5-3 hours. From the chemical structures of the isolated products and $^{13}C$-NMR Spectra of the reaction mixtures, the main conclusion is as follows; 1) Condensation products of II-1-5 were identified from the reaction mixture of vanillyl alcohol treated with alkali and theses compounds afforded the quinonmethide structure(Fig. 3-7) by air oxidation. 2) Treatment of guaiacylglycerol-${\beta}$-aryl ether unit gave ${\varphi}$-aryl-${\beta}$-aroxy quinone structures (IV-15, IV-16), diguaiacyl-1, 4-penta-diene ${\beta}$, ${\beta}$'-diaroxyl distyrene methane unit, ${\beta}$-aroxy distyrene methane. These distyrene methanes of the compounds are transformed by air oxidation into the corresponding o-quinonemethide units (V-8, V-9). 3) On the treatment of phenylcoumaran, the stilbene derivative was formed in quantitative yield and dimerized(VI-11) in preference to oxidation to the corresponding extended quinone structures. The chromophoric structures taken place during the alkaline treatment of the model lignins are thought to be some important types in alkaline pulping on the basis of the reaction mechanism in this experiment.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.8
• /
• pp.99-106
• /
• 2006

In the present study, in order to clarify the effects of latent hydraulic property of granulated blast furnace slag (GBF slag) on the liquefaction, GBF slag was cured in the high temperature alkali water (adding the calcium hydroxide, pH=12, water temperature is about $30^{\circ}C$), and then the cyclic and the static tri-axial compression tests were carried out. Then the results were compared with those for Japanese standard sand of Toyoura sand and natural sand of Genkai sand. From the test results, it is clarified that the liquefaction strength of the GBF slag increases with the increase of the curing period by the hardening due to the latent hydraulic property. It is also shown that GBF slag with Dr=50% and 80% which was cured for 189 days in the fresh-water shows cohesion due to developing of latent hydraulic property. In addition, as for the liquefaction strength of GBFS during the hardening process, a linear relation between the cyclic stress ratio $R_{20}$ at the number of stress cycles Nc=20 and cohesion $C_{d}$ was observed. It is also clarified that the liquefaction strength for cured GBF slag in the high temperature alkali water is predicted by the cohesive strength or the unconfined compressive strength.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.2
• /
• pp.112-119
• /
• 2023

In this study, the variations in CO₂ uptake according to the type and amount of alkali-based activator (Ca(OH)₂, CSA) of geopolymer paste were evaluated. As the amount of activator added to the geopolymer paste increased, the fluidity of the paste is decreased and the compressive strength increased. According to the type of activator, it was confirmed that the addition of Ca(OH)₂ had a greater effect on improving the compressive strength than CSA. As a result of changes in chemical properties according to carbonation curing, the amount of C-S-H and C-A-S-H gels produced before carbonation increased as the amount of activator increased, and amount of CaCO₃ produced after carbonation increased. The reactivity of the blast furnace slag and zeolite increased due to the addition of the activator, and the reactivity tended to increase as the amount of addition increased. As a result of CO₂ uptake, 10.3 wt% when Ca(OH)₂ 10 % was added and 8.77 wt% when CSA 10 % was added was confirmed. It increased by 421 % and 388 % respectively, compared to the case where no activator was added.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.385-390
• /
• 2010

Transesterifications of vegetable oils (soybean oil, grapeseed oil, corn oil, canola oil) by ultrasonic energy were examined on various catalysts for biodiesel production. Reaction activities of the transesterifications were evaluated to the ultrasonic energy and thermal energy. The physicochemical properties and product distribution were also investigated to the biodiesels produced from the oils in the reaction using ultrasonic energy. The yields of fatty acid methyl ester (FAME) on the alkali catalysts were higher than those on the acid catalysts. The highest FAME yield was obtained as 83% on potassium hydroxide catalyst in the transesterification. The effective reaction conditions by ultrasonic energy were 1 wt% catalyst loading and 6:1 molar ratio of methanol to vegetable oils. The reaction rate of the transesterification by ultrasonic energy was faster than that by thermal energy. The acid values of the biodiesel products were improved above 30% compared to those of the feedstocks.

• Food Science of Animal Resources
• /
• v.38 no.2
• /
• pp.315-324
• /
• 2018

The objective of this study was to evaluate the efficacy of alkaline-treated sugarcane bagasse fiber on physicochemical and textural properties of meat emulsion with different fat levels. Crude sugarcane bagasse fiber (CSF) was treated with calcium hydroxide ($Ca(OH_2)$) to obtain alkaline-treated sugarcane bagasse fiber (ASF). The two types of sugarcane bagasse fiber (CSF and ASF) were incorporated at 2% levels in pork meat emulsions prepared with 5%, 10% and 20% fat levels. Alkaline-treatment markedly increased acid detergent fiber content (p=0.002), but significantly decreased protein, fat, ash and other carbohydrate contents. ASF exhibited significantly higher water-binding capacity, but lower oil-binding and emulsifying capacities than CSF. Meat emulsions formulated with 10% fat and 2% sugarcane bagasse fiber had equivalent cooking loss and textural properties to control meat emulsion (20% fat without sugarcane bagasse fiber). The two types of sugarcane bagasse fiber had similar impacts on proximate composition, cooking yield and texture of meat emulsion at the same fat level, respectively (p>0.05). Our results confirm that sugarcane bagasse fiber could be a functional food ingredient for improving physicochemical and textural properties of meat emulsion, at 2% addition level. Further, the altered functional properties of alkaline-treated sugarcane bagasse fiber had no impacts on physicochemical and textural properties of meat emulsions, regardless of fat level at 5%, 10% and 20%.

• Fashion & Textile Research Journal
• /
• v.13 no.2
• /
• pp.263-268
• /
• 2011

One-step reduction/dyeing method was applied for ramie dyeing with natural indigo powder. The effect of reduction/dyeing conditions including the pH of bath, dye temperature and time, and concentration of indigo powder and reduction agent on dye uptake and color properties were investigated. Regardless of addition of alkali, the dyed fabrics appeared in the PB Munsell color range(${\lambda}_{max}$: 660 nm) and the dye uptake was much higher with no addition of sodium hydroxide. Dyeing was carried out through the use of only sodium hydrosulfite in the bath. The maximum dye uptake was obtained at 60 for 30min. Saturated dye uptake was obtained at 2 g/L of sodium hydrosulfite concentration up to 2 g/ L of indigo powder. Whereas, at higher indigo powder concentration (4 g/L), more than 3 g/L of reducing agent concentration was required for obtaining the saturated dye uptake. Color reproducibility was reliable with color difference in the range of 0.03~0.16. Regardless of color strength, fastness to rubbing was acceptable with a 3/4~4/5. Fastness to washing, dry cleaning, and light of samples with low color strength were poor. Whereas, fastness to washing, dry cleaning, and light of samples with high color strength were very good.

• Architectural research
• /
• v.11 no.1
• /
• pp.25-33
• /
• 2009

This study presents the testing of 15 hwangtoh-based cementless concrete mixes to explore the significance and limitations of the development of eco-friendly concrete without carbon dioxide emissions while maintaining various beneficial effects. Hwangtoh, which is a kind of kaolin, was incorporated with inorganic materials, such as calcium hydroxide, to produce a cement-less binder. The main variables investigated were the water-to-binder ratio and fine aggregate-to-total aggregate ratio to ascertain the reliable mixing design of hwangtoh-based cementless concrete. The variation of slump with elapsed time was recorded in fresh concrete specimens. Mechanical properties of hardened concrete were also measured: including compressive strength gain, splitting tensile strength, moduli of rupture and elasticity, stress-strain relationship, and bond resistance. In addition, mechanical properties of hwangtoh-based cement-less concrete were compared with those of ordinary portland cement (OPC) concrete and predictions obtained from the design equations specified in ACI 318-05 and CEB-FIP for OPC concrete, wherever possible. Test results show that the mechanical properties of hwangtoh-based concrete were significantly influenced by the water-to-binder ratio and to less extend by fine aggregate-to-total aggregate ratio. The moduli of rupture and elasticity of hwangtoh-based concrete were generally lower than those of OPC concrete. In addition, the stress-strain and bond stress-slip relationships measured from hwangtoh-based concrete showed little agreement with the design model specified in CEB-FIP. However, the measured moduli of rupture and elasticity, and bond strength were higher than those given in ACI 318-05 and CEB-FIP. Overall, the test results suggest that the hwangtoh-based concrete shows highly effective performance and great potential as an environmental-friendly building material.