• International Journal of Air-Conditioning and Refrigeration
• /
• 제13권1호
• /
• pp.44-50
• /
• 2005

In the present study, the characteristics of upward bubble flow were experimentally investigated in a liquid bath. An electro-conductivity probe was used to measure local volume fraction and bubble frequency. Since the gas was concentrated at the near the nozzle, the flow parameters were high near the nozzle. In general their axial and radial values tended to decrease with increasing distance. For visualization of flow characteristics, a Particle Image Velocimetry (PIV) and a thermo-vision camera were used in the present study. The experimental results showed that heat transfer from bubble surface to water was largely completed within z = 10 mm from the nozzle, and then the temperature of bubble surface reached that of water rapidly. Due to the centrifugal force, the flow was more developed near the wall than at bubble-water plume. Vortex flow in the bottom region was relatively weaker than that in the upper region.

• 한국입자에어로졸학회지
• /
• 제18권3호
• /
• pp.61-68
• /
• 2022

In this study, a fluidized bed particle generator was developed to generate an aerosol without supply of compressed air and to increase portability. It was assumed that the mixing ratio of the test particles and beads, the input amount, and the air flow rate supplied to the generator would have effect on the aerosol generation characteristics. The product of these three parameters was set as a characteristic parameter and particle generation characteristics according to the change of the characteristic parameter were observed. As a result, it was confirmed that the input amount of test particles and beads was not suitable as a characteristic parameter and a characteristic parameter expressed as a product of the mass mixing ratio and the air flowrate was newly defined. When the new characteristic parameter is applied, it can be confirmed that the total amount of particles generated from the particle generator is a function of the characteristic parameter. As a result of measuring the amount of particle generation by adjusting the characteristic parameter, it was confirmed that the performance required for the test particle generator for the field inspection equipment of PM-2.5 sensors could be satisfied.

• 설비공학논문집
• /
• 제6권1호
• /
• pp.29-38
• /
• 1994

Particle contamination into and out of a cavity-cylindrical cavities with aspect ratios(width/depth) less than, equal to 1 and langer than 1, and also three dianensional T's attached to a cylindrical flow tube was studied numerically, using a finite difference method. In the process of unsteady particle diffusion, the particles contained in a concentration boundary layer near the tube wall plays an important role in the initial stage, after which a quasi-steady concentration profile is developed inside the cavity, resulting in an exponential change of concentration with time. Average concentration and its rate of change are observed to be closely correlated by a power law function in terms of Reynolds number and the logarithm of Schmidt number. Effects of the three parameters-Re, Sc, and aspect ratio-are analysed and well explained.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제44회 KOSCO SYMPOSIUM 초록집
• /
• pp.241-243
• /
• 2012

Experiments were conducted to get the design concepts for the continuous aluminum particle feeding system. Two opposed cylinders were used. Aluminum particles in one cylinder were ejected to the air by the supplying gas and the pressure of the other cylinder. It was not possible to eject more aluminum mass flowrate than that of gas if particles were just thrust by the pressure difference between two cylinders. Aluminum particle/air mixture in the flow system was successfully ignited by the electric spark.

• 대한기계학회논문집B
• /
• 제27권11호
• /
• pp.1604-1611
• /
• 2003

The experimental investigation of a coal splitter used in the 500㎿(e) boilers of fossil power plant is carried out to validate the design criteria. To predict air flow and the amount of particles at the exit, velocity and the weight of particles are measured on test planes using the coal splitter model with two-dimensional phase doppler particle analyzer and the glass fiber filter. It is found that the position of guide plate influences significantly both flow rates of gas and particle at the exit. Gas flow rate was a linear function of the guide plate, whereas particle flow rate was a exponential function of it.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권1호
• /
• pp.88-93
• /
• 2000

In this study, the mixing process of two-phase flow generated by two jets with height difference is analyzed. The primary jet is jetted on the condition of the state mixed pulverized solid particles with air. The height difference between the main jet and the secondary jet is changed into three kinds(0, 32.5, 47.5mm). The velocity vector field, concentration field and turbulent properties of solid particles are measured by using 3-Dimensional Particles Dynamics Analyzer. As the height difference of two jets through the two nozzles increases, the solid particle recirculation zone and the dense zone in the combustion chamber become large. The solid particle concentration at the center of the combustion chamber gets dense because the particle velocity remains slow due to the existence of the solid particle recirculation zone. The particle concentration in the combustion chamber can also be influenced by the hight difference of two jets.

• 한국입자에어로졸학회지
• /
• 제13권4호
• /
• pp.173-182
• /
• 2017

An Eulerian-Lagrangin approach is used to compute particle dispersion from a power plant chimney. For air flow, three-dimensional incompressible filtered Navier-Stokes equations are solved with a subgrid-scale model by integrating the Newton's equation, while the dispersed phase is solved in a Lagrangian framework. The velocity ratios between crossflow and a jet of 0.455 and 0.727 are considered. Flow fields and particle distribution of both cases are evaluated and compared. When the velocity ratio is 0.455, it demonstrates a Kelvin-Helmholtz vortex structure above the chimney caused by the interaction between crossflow and a jet, whereas the other case shows flow structures at the top of the chimney collapsed by fast crossflow. Also, complex wake structures cause different particle distributions behind the chimney. The case with the velocity ratio of 0.727 demonstrates strong particle concentration at the vortical region, whereas the case with the velocity ratio of 0.455 shows more dispersive particle distribution. The simulation result shows similar tendency to the experimental result.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2004년도 하계학술발표 논문집
• /
• pp.171-171
• /
• 2004

• 한국가스학회지
• /
• 제13권5호
• /
• pp.7-14
• /
• 2009

본 연구는 석탄화력발전소 노의 연소효율 향상을 위하여 미분탄 수송배관의 공기-입자 유동장의 압력손실 특성을 분석하여 미분탄 수송장치 내에 설치되어 유량을 제어하는 오리피스의 설계에 적용하고자 하는 것이다. 통상의 미분탄 수송배관장치는 관의 형태에 따라 직선관, 곡선관 및 엘보우로 구성된다. 본 연구에서는 공기유동과 입자운동의 상호작용 해석을 통하여 직선관과 곡선관을 갖는 미분탄 수송배관장치 내의 압력손실을 분석하였다. 총 압력손실은 공기-미분탄 입자의 마찰 손실 증가와 배관의 길이, 곡선관 각도의 증가에 따라 증가하는 것으로 확인되었다. 연구결과로 압력손실과 유량제어를 위한 최적화된 오리피스 설계 프로그램이 개발되었으며 그 계산 결과를 기존의 실험결과와 비교, 분석하였다.

• 설비공학논문집
• /
• 제14권4호
• /
• pp.315-323
• /
• 2002

The commercial viability of heat exchanger is mainly dependent on their long-term fouling characteristics because the fouling increases the pressure loss and degrades the thermal performance of a heat exchanger. An experimental study was performed to investigate the characteristics of fluid flow and heat transfer in a fluidized bed heat exchanger with circulating various solid particles. The present work showed that the drag force coefficients of particles in the internal flow were higher than those in the external flow, in addition, the solid particle periodically hitting the tube wall broke the thermal boundary layer, and increased the rate of heat transfer. Particularly when the flow velocity was low, the effect was more pronounced.