• 열처리공학회지
• /
• 제12권4호
• /
• pp.303-312
• /
• 1999

An investigation of the CrMoV rotor steel weldment which experienced by cyclic thermal aging heat treatment and as-received condition was performed. This evaluation was carried out to confirm whether this type of weldment is appropriate for the service environment in terms of microstructural examinations, microhardness measurements and tensile tests. The cyclic thermal aging heat treatment, containing continuous heating and cooling thermal cycle was programmed to simulate the real rotor service condition. The heat treatment was performed for 40 cycles(5920hrs). The results indicated that the weldment was composed of 4 different regions such as heat affected zone of the base metal, butter weld(initial weld), full thickness weld(final weld) and the base metal. The double welding process was applied to eliminate the susceptibility of reheat cracking at heat affected zone of base metal. The grain refinement at the HAZ due to the welding process could reduce the possibility of cracking susceptibility, but its tensile properties was appeared to be low due to the weld metal in as-received condition. The benefit effect, grain refinement was extended with carbides coarsening during the cyclic thermal aging heat treatment. However the poor mechanical properties of the weldment was more degraded as undergoing the heat treatment.

• 보존과학회지
• /
• 제35권5호
• /
• pp.416-429
• /
• 2019

보채는 지류문화재 보존처리의 마지막 단계로 주로 봉채를 사용한다. 본 연구는 지류문화재 보채에 쓰이는 4종의 봉채(본람, 등황, 연지, 대자)를 한지에 채색한 후 채색 양상을 확인하고 인공열화를 통해 색변화 양상을 확인하고자 하였다. 채색 양상을 관찰한 결과 본람·연지·대자는 미세한 안료 입자가 도포되는 형태였으며, 등황은 피막을 형성하였다. 봉채의 X선 회절분석 결과 본람과 연지, 대자에서 석영과 방해석, 납석이 공통적으로 검출되었고, 대자에서 침철석이 추가로 검출되었다. 인공열화 결과 습열열화에서 등황이 노란색에서 주황색으로 변색되었으며, 자외선열화에서는 등황과 연지가 탈색되었다. 결과적으로 봉채로 보채된 지류문화재는 등황이 채색된 경우 알칼리에 의해 주황색으로 변색될 수 있으며, 자외선에 의해 등황과 연지의 탈색이 우선적으로 발생하여 전체적인 색상이 어두워짐을 예측할 수 있다.

• 한국재료학회지
• /
• 제29권6호
• /
• pp.392-397
• /
• 2019

A cold roll-bonding process is applied to fabricate an AA6061/AA5052/AA6061 three-layer clad sheet. Two AA6061 and one AA5052 sheets of 2 mm thickness, 40 mm width, and 300 mm length are stacked, with the AA5052 sheet located in the center. After surface treatment such as degreasing and wire brushing, sample is reduced to a thickness of 1.5 mm by multi-pass cold rolling. The rolling is performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 400 mm at rolling speed of 6.0 m/sec. The roll bonded AA6061/AA5052/AA6061 complex sheet is then hardened by natural aging(T4) and artificial aging(T6) treatments. The microstructures of the as-roll bonded and age-hardened Al complex sheets are revealed by optical microscopy; the mechanical properties are investigated by tensile testing and hardness testing. After rolling, the roll-bonded AA6061/AA5052/AA6061 sheets show a typical deformation structure in which grains are elongated in the rolling direction. However, after T4 and T6 aging treatment, there is a recrystallization structure consisting of coarse equiaxed grains in both AA5052 and AA6061 sheets. The as roll-bonded specimen shows a sandwich structure in which an AA5052 sheet is inserted into two AA6061 sheets with higher hardness. However, after T4 and T6 aging treatment, there is a different sandwich structure in which the hardness of the upper and lower layers of the AA6061 sheets is higher than that of the center of the AA5052 sheet. The strength values of the T4 and T6 age-treated specimens are found to increase by 1.3 and 1.4 times, respectively, compared to that value of the starting material.

• 한국재료학회지
• /
• 제32권3호
• /
• pp.161-167
• /
• 2022

A cold roll-bonding process is applied to fabricate an AA6061/AA5052/AA6061/AA5052 layered sheet. Two AA6061 and one AA5052 sheets of 2mm thickness, 40mm width and 300mm length are alternately stacked, then reduced to a thickness of 2.0 mm by multi-pass cold rolling after surface treatment such as degreasing and wire brushing. The rolling is performed at ambient temperature without lubricant using a 2-high mill with a roll diameter of 400 mm at a rolling speed of 6.0 m/sec. The roll-bonded AA6061/AA5052/AA6061/AA5052 layered sheet is then hardened by natural aging (T4) and artificial aging (T6) treatments. The microstructure of the as-roll bonded and the age-hardened Al sheets was revealed by SEM observation; the mechanical properties were investigated by tensile testing and hardness testing. After T4 and T6 aging treatment, the specimens had a recrystallization structure consisting of coarse equiaxed grains in both AA5052 and AA6061 regions. The as-roll-bonded specimen showed a clad structure in which the hardness of AA5052 regions was higher than that of AA6061 regions. However, after T4 and T6 aging treatment, specimens exhibited different structures, with hardness of AA6061 regions higher than that of AA5052 regions. Strengths of T6 and T4 age-treated specimens were found to increase by 1.55 and 1.36 times, respectively, compared to the value of the starting material.

• 한국재료학회지
• /
• 제33권12호
• /
• pp.565-571
• /
• 2023

AA1050/AA6061/AA1050 layered sheet was fabricated by cold roll-bonding process and subsequently T4 and T6 aging-treated. Two commercial AA1050 sheets of 1 mm thickness and one AA6061 sheet of 2 mm thickness were stacked up so that an AA6061 sheet was located between two AA1050 sheets. After surface treatments such as degreasing and wire brushing, they were then roll-bonded to a thickness of 2 mm by cold rolling. The roll-bonded Al sheets were then processed by natural aging (T4) and artificial aging (T6) treatments. The as roll-bonded Al sheets showed a typical deformation structure, where the grains are elongated in the rolling direction. However, after the T4 and T6 aging treatments, the Al sheets had a recrystallized structure consisting of coarse grains in both the AA5052 and AA6061 regions with different grain sizes in each. In addition, the sheets showed an inhomogeneous hardness distribution in the thickness direction, with higher hardness in AA6061 than in AA1050 after the T4 and T6 age treatments. The tensile strength of the T6-treated specimen was higher than that of the T4-treated one. However, the strength-ductility balance was much better in the T4-treated specimen than the T6-treated one. The tensile properties of the Al sheets fabricated in the present study were compared with those in a previous study.

• 농업과학연구
• /
• 제43권1호
• /
• pp.61-71
• /
• 2016

The effect of postmortem aging on the quality of Semimembranosus muscle (SM) from Hanwoo was investigated. The quality of SM was compared with that of Longissimus dorsi muscle (LD). SM contained higher moisture, protein, and ash, and lower fat than LD (p<0.05). The $a^*$ and $b^*$ values of SM were significantly decreased after 21 days of aging. SM showed higher $a^*$ values than LD at 1 and 7 day of aging (p<0.05). The cooking loss of SM was not affect by aging. SM had higher cooking loss than that of LD throughout the aging period. Although the shear force of SM was significantly decreased by aging, SM showed high shear force compared to LD during aging period (p<0.05). Aging increased lipid oxidation in both muscles (p<0.05). However, TBARS value of SM was significantly lower than that of LD throughout the aging period (p<0.05). There was no effect of aging on the betaine and L-carnitine contents of SM. SM contained higher betaine and L-carnitine than LD in all aging days (p<0.05). Therefore, we concluded that consumer acceptability of SM could be increased by aging based on the increase of tenderness in addition to its high nutritional properties.

• 한국생산제조학회지
• /
• 제8권4호
• /
• pp.123-129
• /
• 1999

Although type 316 stainless steel is widely used such as in reactors of petrochemical plants and pipes of steam power plants and s attracting attention as potential basic material for the fast breeder reactor structure alloys in nuclear power plants and is attracting attention as potential basic material for the fast breeder reactor structure alloys in nuclear power plants the effect of precipitates which form during the long term exposure at service temperature on creep properties is not known sufficiently. In this study to investigate the creep properties and the influence of prior aging on the microstructure to form precipitates specimens were first solutionized at 113$0^{\circ}C$ for 20 minutes and then aged for different times of 0 hr, 100 hrs, 1000 hrs and 2200 hrs at 75$0^{\circ}C$ After heat treatments tensile tests both at room temperature and $650^{\circ}C$ and constant load creep ruptuere tests were carried out.

• 한국인쇄학회지
• /
• 제30권3호
• /
• pp.13-21
• /
• 2012

This study was carried out to evaluate the stability of archival documents produced using papers. The properties of archival documents depend on the type of fillers of papers that are used such as fiber, non cellulose fiber, and mineral. The physio-chemical characteristics of archival documents were analyzed by employing acid hydrolysis against cellulose fiber substances. Fibers of Korean hand-made (Hanji), flex, and cotten papers showed higher pH and the degree of polymerization (DP) than wood fiber and mechanical fiber. Mechanical pulp containing 12.8% of lignin showed the greatest decrease of DP due to acid hydrolysis, and this resulted in increase of degree of aging. The filler found to clay and talc did not contain metal such as $Fe^{+2}$, $Fe^{+3}$, and $Cu^{+2}$. The alkaline metals such as Mg, Ca, and Ti showed greater resistance to acid hydrolysis.

• Elastomers and Composites
• /
• 제3권1호
• /
• pp.32-38
• /
• 1968

The physical properties of NR-SBR and NR-BR blends were studied. 1. In blending, tensile strength decreased with increase in synthetic rubber contents. It was most effective when the ratio of NR/Syn. R is 75/25. 2. Tensile strength decreased with order of NR, SBR and BR and modulus after aging is proportional of synthetic rubber contents. 3. Elongation is less influenced by synthetic rubber ratio that on the other hand, the decrease of elongation is proportional to synthetic rubber contents after aging. 4. Hardness decreased with increase in the synthetic rubber contents and on the other hand, the hardness increased after aging.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.613-618
• /
• 2002

Steel slag produced in steel making process is divided with electric arc furnace slag and converter slag. Compared with the blast furnace slag, converter slag has the expansibility due to the reaction with water and free CaO. Therefore it is specified in Standard Specification for Concrete in Korea that steel slag aggregate must not be used in concrete. In this study, we treat electric arc furnace slag aggregate(EAFSA) for concrete before and after several aging process to reduce expansibility. The fundamental properties are measured, which are specific gravity, unit weight, abrasion value and immersion expansion ratio, as concrete aggregate. To understand the suitability of EAFSA for concrete, we made the concrete with EAFSA and then determined the strength and the volume change in EAFSA concrete. From the results EAFSA treated with steam aging process has potentiality for concrete aggregate.