• Journal of the Korean Wood Science and Technology
• /
• 제19권4호
• /
• pp.18-26
• /
• 1991

This study was carried out to examine not only the effect and the process of activation of aluminum sulfate for the manufacture of PB and MDF, but also application of the activation treatment to PB and MOF made with MDI adhesive. The results were as follows: 1. For the manufacture of PB, activating effect did not take place Because the low moisture content of 30% in the process of activation treatment made probably insufficient activation. It needs to examine higher moisture content for the uniform and enough activation same as that of MOF. 2. In the case of MOF, Activating effect was excellent, it showed not only better results of MOR 48%, MOE 29%, IB 60% than those of the control but also better dimensional stability. 3. Application of alum activation to the PB and MDF made with MDI adhesive yielded no effects. Maybe it was the reson that the curing mechanism of MDI is different. 4. Modifing the wood surface was the oxidation and wettability was not the variable limiting glueline performance. It is necessary to make a more study about activating reaction.

• 약학회지
• /
• 제34권3호
• /
• pp.155-160
• /
• 1990

An oral adhesive tablet of acyclorir [9-(2-hydroxyethoxymethyl) guanine] for herpetic stomatitis was prepared and its physical properties were evaluated. 300 mg weighed tablets containing 30 mg of acyclovir were prepared with six kinds of polymers from direct compression, and the stickiness, fracture resistance and dissolution in pH 6.8 buffer solution were tested. HPMC and MC showed good stickiness and fracture resistance, and their dissolution rates were significantly different from each other. Three factors-HPMC:MC ratio, acyclovir content, compression force-were chosen as an important factor of manufacture and factorial analyses for these three factors were carried out. Eight kinds of formulations from different combination of three factors were prepared and tested in stickiness, fracture resistance and dissolution in pH 6.8 buffer solution. Dissolution rate was significantly affected by polymer ratio, fracture resistance was affected by compression force, and stickiness was not significantly affected by acyclovir content and polymer ratio.

• 접착 및 계면
• /
• 제3권1호
• /
• pp.13-19
• /
• 2002

We have studied on the surface and adhesion properties for acrylic terpolymers, having both hydrophobic and hydrophilic side chains, synthesized via solution polymerization. In order to develop a waterborne material. we tried to synthesize these terpolymers via emulsion polymerization. The polymeric emulsion synthesized was mainly composed of methyl methacrylate (MMA), methoxy-polyethyleneglycol methacrylate (MPEGMA) having hydrophilic side chains and methoxypolypropyleneglycol methacrylate (MPEGMA) having hydrophobic side chains. The viscosities of this series increased with an increase in the content of the co-monomer such as MPEGMA and (MPEGMA). This behavior resulted in the increase in the diameter and heterogeneity of the emulsion particle via AFM observation. Furthermore. the tensile adhesion strength and 90-degree peel strength of the adhesive of these polymeric emulsions were measured. In the case of polymeric emulsion composed of the same content of both hydrophilic and hydrophobic component, the adhesion property showed the highest value. However, since the adhesion properties as a practical applicable adhesive were poor, some improvements were required. When the composition above was modified with butyl acrylate (BA), the improvement effect on adhesion strength was accepted. In particular, 90-degree peel strength increased up to a maximum of 400% of the original value.

• 반도체디스플레이기술학회지
• /
• 제15권1호
• /
• pp.12-16
• /
• 2016

Toluene-free pressure sensitive adhesives were synthesized by using butyl acrylate (BA), 2-hydroxy ethyl acrylate, methyl methacrylate, acrylic acid (AA) as monomers and ethyl acetate as a solvent. The polymerization recipes were designed by changing 1, 3, 5 part per hundreds monomer (phm) of AA content on the basis of 100 BA parts. Two crosslinking agents, ethyl glycol diglycidyl ether (EDGE) and isophorone diisocyanate (IPDI) were added to the synthesized polymers to increase adhesion due to crosslinking. In the measurement of properties, holding power, peel strength, and initial tackiness increased with AA content due to crosslinking between carboxyl group in AA and epoxy group in EDGE and isocyanate group in IPDI. In the comparison of two crosslinking agents, EDGE showed better in the three properties than IPDI by better reaction of epoxy group of EDGE to carboxyl group of AA.

• Journal of the Korean Wood Science and Technology
• /
• 제25권3호
• /
• pp.16-23
• /
• 1997

This study was carried out to discuss feasibility of high density polyethylene(HDPE) as a new substitute for the conventional adhesives in plywood manufacture. Plywood was composed of radiata pine(Pinus radiata) and Malas(Homallium feotidium) veneers and bonded by HDPE. Adhesion characteristics and anatomical scanning has been examined through tensile-shear strength test and scanning electron microscopy(SEM). The results are as follows; 1. Optimum loading quantity was 15g/$(30.3{\times}30.3)cm^2$, and tensile-shear strength increased with the increase of loading quantity. 2. Even at the hot pressing time of 1 minute, tensile-shear strength met the value of KS(over the 7.5kgf/$cm^2$), and tensile-shear strength increased with the increase of hot pressing time. 3. Plywood composed of veneer at moisture content of 19.6% showed similar tensile-shear strength to that at air conditioned moisture content of 11.4%. 4. Under the same condition of hot pressing time, tensile-shear strength of plywood bonded by HDPE met the KS value of boil and wet test and proved the same group as phenol formaldehyde adhesive. 5. HDPE films showed mechanical adhesion through penetration into the lathe check and ray of veneer.

• 접착 및 계면
• /
• 제23권2호
• /
• pp.33-38
• /
• 2022

본 연구에서는bio polyol 함량에 따라 bio polyol based 친환경 수분산 폴리우레탄을 합성하고 그 특성을 알아보고자 하였다. Polyester polyol(DT-1040)과 castor oil based polyol(COP)의 비율에 따른 bio polyol based 수분산 폴리우레탄을 성공적으로 합성한 것을 확인할 수 있었다. 합성된 bio polyol based 수분산 폴리우레탄의 Tg는 -70 ℃와 -30 ℃ 부근에서 나타났으며, COP의 함량이 증가할수록 유리전이온도 구간이 넓어지는 것을 확인할 수 있었다. 또한, COP의 함량이 증가할수록 인장강도는 감소하였고, 접착력은 DT-1040:COP=7:3일 때 최고값을 나타내었다.

• Composites Research
• /
• 제30권4호
• /
• pp.254-260
• /
• 2017

본 논문에서는 알루미늄과 복합재료에 대한 이종소재 접합면의 성형안전성을 위해 일정한 두께를 확보할 수 있는 0.1 mm, 0.2 mm, 0.3 mm bead의 적용 방법과 물성변화에 대해 연구하였고, 이를 검증하기 위해 더블랩 시험과 FEM 시뮬레이션으로 접착제의 두께에 따라 미치는 영향을 평가하였다. 그 결과, 접착제에 bead의 양을 1% 이상 함량이 증가함에 따라 접착 소재의 강도가 높아지고 신율이 감소함을 확인하였고, bead의 크기가 커질수록, 강성은 낮아지고, 신율은 증가함을 확인하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제26권3호
• /
• pp.48-52
• /
• 1998

Residues such as walnut, pinenut and peanut shells were used as a filler in adhesive for bonding radiata pine plywood. The nutshell residues were prepared by simply drying to 8% moisture content and grinding the dry material using a laboratory Wiley mill with a $75{\mu}m$ (200 mesh) screen. The nutshells residues were compared to a commercial filler commonly used in adhesives by the structural plywood and laminated veneer lumber industry in the United States. The adhesive mixes were made by following the recommended procedure of Georgia-Pacific Resins, Inc., using phenol-formaldehyde resin. For each filler type, three-ply plywoods, 6 mm nominal thickness and 30 by 30 cm in size, were fabricated at two press times (4 and 5 min) and around 30 minute assembly time. Evaluations of the nutshell residues were carried out by tension shear tests after cyclic boil tests on plywood. The results of the performance test included tension shear strength and wood failure. All plywoods made with the nutshell fillers were comparable to those made with the control filler. These results indicate that nutshell residues would be suitable as filler for plywood adhesives.

• Journal of the Korean Wood Science and Technology
• /
• 제47권2호
• /
• pp.239-248
• /
• 2019

This research presents an improvement of the physical and mechanical properties of composite board (com-ply) made of Oriented Strand Board (OSB) coated with wood veneer of Pine (Pinus merkusii), Avocado (Persea Americana) and Mahogany (Swietenia mahogany). 1.5 mm thick veneers of those three wood types were adhered to the surface of OSB using two adhesive types: epoxy and isocyanate. The adhesive with the glue spread of $250g\;m^{-2}$ applied using single glue line was spread and then cold pressed with the pressure of $15kg\;cm^{-2}$ for 3 hours. The research result showed an improving dimension stability of com-ply, but not found on all parameters of physical property test. The moisture content seemed to be influenced by the com-ply type, yet not related to its thickness swelling, water absorption and linear expansion. The exception took place in the parallel linear expansion when immersed for 2 hours. The highest to the lowest increases of MOE and MOR were consecutively found on OSB coated with wood veneer of Pine, Mahogany and Avocado. However, the increases were statistically insignificant. The highest increasing screw hold power was found at the com-ply type AE (avocado veneer and epoxy adhesive) that was by 28%.

• 한국응용과학기술학회지
• /
• 제37권6호
• /
• pp.1627-1634
• /
• 2020

본 연구에서는 수성 아크릴계 점착제의 물성에 대한 주 단량체의 측쇄 사슬의 영향을 비교하기 위해 주 단량체로 각각 ethyl acrylate, 2-ethylhexyl acrylate, lauryl methacrylate를 사용하여 acrylic acid, 2-hydroxyethyl acrylate와 공중합체를 합성하여 수성 아크릴 점착제를 제조하였다. 제조한 수성 아크릴 점착제의 고형분, 평균입도분포, 초기점착력, 최대점착력, 박리강도, 내열점착력 등의 물리적 특성을 비교하였다.