• Journal of the Korean Wood Science and Technology
• /
• 제26권1호
• /
• pp.97-105
• /
• 1998

This study examined the combined using effects of urea-formaldehyde (UF) resin and emulsifiable methylene diphyenyl diisocyanate (EMDI) resin to overcome performance limit of three-layer particleboards commonly made by UF resin. Two adhesive adding methods were applied with three types of resin combination system to each layer of particleboards. The one was simultaneously spreading method with emulsified compound resin (UF and EMDI) while the other was separately spreading method with unemulsified EMDI resin after UF resin spreading. The performance of particleboards bonded with 2% EMDI resin to the inner layers(IL) were similar to that of controls bonded with 8% UF resin. In the case of the emulsified compound resin application to the all layers of particleboards, there were marked reinforcing effects of EMDI resin, although a small amount of EMDI resin was mixed with UF resin. Especially bending MOR after 24 hours cold water-immersion and thickness swelling after 2 hours hot water-immersion of compound resin-bonded particleboards were remarkably different from those of pure UF resin-bonded particleboards. It was found that separately spreading method with unemulsified EMDI resin was more effective than simultaneously spreading method with emulsified compound resin to sustain the internal bond strength of particleboards after 24 hours cold water-immersion. In the resin combination systems to outer layers/inner layers of particleboards, water resistance and strength properties were superior in order of UF+EMDI/UF+EMDI > UF/UF+EMDI > UF/UF. And water resistance of particleboards was greatly dependent upon EMDI resin level in any adhesive adding method.

• Journal of the Korean Wood Science and Technology
• /
• 제8권2호
• /
• pp.1-5
• /
• 1980

This study is carried out to determine the scavenging effect of resorcinol added into the urea formaldehyde resin on the formaldehyde release of plywood, as the preliminary study of using the phenolic substances. The method for formaldehyde determination used in this report is the improved chromotropic acid determination. The results are summarized as follows: 1. Resorcinol added into the urea formaldehyde adhesive acts as a good scavenger. 4 percent of resorcinol reduced the formaldehyde release to less than half content. 2. Adding resorcinol gave better glue shear strength than that of control, showing the peak of the shear strength, at 2 percent and decreased to the same strength as control along its content of 4 percent. 3. Moisture content of air dried plywood met the standard very well.

• 한국응용곤충학회지
• /
• 제47권4호
• /
• pp.491-495
• /
• 2008

초콜렛 포장에 스티커를 붙이기 위해 사용되는 접착물에 계피(Cinnamonum cassia Blume) 추출물을 혼합하는 것은 화랑곡나방(Plodia interpunctella Hubner)에 의한 침입으로부터 초콜렛 제품을 보호하기 위한 효과적인 한 방법이다. 처리농도별 제품을 개별적으로 투입한 비선택 실험에서 0.02와 0.025%의 계피 추출물을 처리한 포장지로 포장된 초콜렛 제품은 $28.1^{\circ}C$와 70-75%의 실험 조건에서 30일까지 화랑곡나방이 침입하지 않았으나, 계피 추출물이 첨가되지 않은 포장은 화랑곡나방에 의해 침입되었다. 처리농도별 제품을 혼합 투입한 선택 실험에서 0.02와 0.025%의 계피 추출물을 처리한 포장지로 포장된 초콜렛 제품은 $28.1^{\circ}C$와 70-75%의 실험 조건에서 60일까지 화랑곡나방에 의해 침입받지 않았는데 반해, 계피 추출물이 첨가되지 않은 제품은 화랑곡나방에 의해 침입을 받았다. 제품의 계피향 흡착 유무를 알아보기 위해 실시한 패널 테스트 결과 포장지에 계피 추출물을 처리하여도 제품에 향이 흡착되지 않아 소비자의 선택에 영향을 미치지 않을 것이라 판단되었다.

• Journal of the Korean Wood Science and Technology
• /
• 제24권2호
• /
• pp.15-19
• /
• 1996

To utilize the waste materials and develope wood adhesive from isolated bloods of slaughtered cow and pig and also to prevent water pollution, simple and rapid method of isolation and purification of plasma proteins from pig bloods with trichloroacetic acid(TCA) treatment was developed. Adding of TCA-precipitated blood powder to the phenol formaldehyde resin(PF) improved dry and wet strength of plywood and resulted in fast hot pressing times.

• 접착 및 계면
• /
• 제21권3호
• /
• pp.93-100
• /
• 2020

적층제조법 기반의 3D 프린팅 기술은 사용자가 원하는 상품을 출력하여 제공하지만 고온의 사용 환경 및 용융된 필라멘트 수지의 냉각 과정에서 변동적 수축현상이 발생하여 상품의 출력편차를 야기한다. 본 연구에서는 출력물의 들뜸과 뒤틀림을 방지하고 정밀한 형상의 고품질 출력물을 제작하기 위하여 3D 프린터 빌드시트용 아크릴 점착제를 연구하였다. 고온에서 점착특성이 유지되고 점착제로부터 출력물의 안착과 원활한 탈거를 위해 부착성과 강인성이 우수하고 높은 유리전이온도를 갖는 4-acryloylmorpholine (ACMO)를 첨가하여 무용제 타입의 점착제 조성물을 설계하였다. 단량체의 후첨가방식을 사용하여 두 단계를 통해 아크릴 조성물을 합성하였고, 합성된 조성물로 코팅한 점착제 필름을 다각도에서 분석하였다. 그 결과 제조된 점착제는 높은 유리전이온도를 보이고 열처리 전/후에 따른 박리강도 차이가 보이지 않았으며, 유변학적 물성 분석을 통해 점착제의 우수한 접착력 뿐만 아니라 변형 없이 탈착이 가능한 물성을 갖음을 확인하였다. 본 연구에서 제조된 점착제를 3D 프린터의 빌드시트로 활용하였을 때 안착성 및 작업성이 양호하고 출력편차가 적은 출력물을 얻었다. 기존 판매중인 빌드시트와 비교하였을 때 본 연구에서 제조한 점착제 위에서는 출력물이 원활하게 탈거가 가능하기 때문에 FDM 방식 3D프린터의 사용자들에게 작업 편의성을 제공할 수 있을 것으로 기대된다.

• Structural Monitoring and Maintenance
• /
• 제6권1호
• /
• pp.47-66
• /
• 2019

One method of retrofitting concrete structures is to use fiber reinforced polymers (FRP). In this research, the shear, torsional and flexural strengthening of self-compacting reinforced concrete (RC) girders are fulfilled with glass fiber reinforced polymer (GFRP) and carbon fiber reinforced polymer (CFRP) materials. At first, for verification, the experimental results were compared with numerical modeling results obtained from ABAQUS software version 6.10. Then the reinforcing sheets were attached to concrete girders in one and two layers. Studying numerical results obtained from ABAQUS software showed that the girders stiffness decreased with the propagations of cracks in them, and then the extra stresses were tolerated by adhesive layers and GFRP and CFRP sheets, which resulted in increasing the bearing capacity of the studied girders. In fact, shear, torsion and bending strengths of the girders increased by reinforcing girders with adding GFRP and CFRP sheets. The samples including two layers of CFRP had the maximum efficiencies that were 90, 76 and 60 percent of improvement in shear, torsion and bending strengths, respectively. It is worth noting that the bearing capacity of concrete girders with adding one layer of CFRP was slightly higher than the ones having two layers of GFRP in all circumstances; therefore, despite the lower initial cost of GFRP, using CFRP can be more economical in some conditions.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.49-52
• /
• 2008

The present study was to develop a dry PFB method similar to the existing gypsum board construction method in order to apply the existing wet PFB method that uses fire-resistant adhesive. It was found that the existing wet method can produce concrete compressive strength of 80MPa and fire resistance of 3 hours with 30mm PF boards. The goal of development in this study was fire resistance of 3 hours through dry construction of 15mm fire-resistant boards. 1. Improved PF board was prepared by adding inorganic fiber to existing board and using aggregate with grain size of 3mm or less. Molding was done at temperature higher than that for existing PF board molding. While wet curing is used for existing PF boards, this study used dry curing in order to enhance heat insulation performance. 2. According to the results of fire resistance test, when the dry PF method was applied, the temperature of the main reinforcing bar was 116℃ in 15mm, 103.8℃ in 20mm, and 94℃ in 25mm, and these results satisfied the current standards for fire resistance control presented by the Ministry of Land, Transport and Maritime Affairs. When a 3-hour fire resistance test was performed and the external properties of the specimen were examined, the outermost gypsum board hardly remained and internal PF board maintained its form without thermal strain.

• 대한치과보철학회지
• /
• 제39권5호
• /
• pp.492-501
• /
• 2001

The use of alginate impression materials today is prevalent because of its efficiency and simplicity in clinical settings. Unfortunately, the simplicity of the procedure tends to lull the dentist into a sense of well-being, and lead him into using careless or sloppy technique. Alginate impression materials are used to fabricate diagnostic and preliminary casts, and the final cast. Incorrect use of this material is known to affect the accuracy of the final prosthesis. The purpose of this study was to compare the effect of different mixing methods of alginate impression material and tray adhesive on the accuracy of the stone cast produced by each method. A total of 30 stone casts were produced by using 3 different types of mixing methods (10 stone cast for each mixing method, respectively). The first method utilized an automatic-mixing machine to mix alginate while the second method was carried out manually, strictly following manufacturer's instructions. The third method also involved manual mixing, but did not follow the manufacturer's instructions and was done in a random fashion. Also, 20 additional stone casts were produced by using alginate with or without tray adhesives were included in the study to evaluate effects of tray adhesives on the accuracy of alginate impression. 10 stone casts were produced by adding tray adhesives to the interior surface of the impression tray prior to taking the impression. The other 10 excluded this step. A total of 50 stone casts were analyzed by the three-dimensional measuring machine to measure and compare the dimensional changes of the impression material of each group. The results are as follows. 1. No significant difference was found between the automatic mixing group and the manually-mixing group(p>0.05). 2. For the group that followed manufacturer's instructions, less dimensional changes were record ed than the group that didn't in measuring distanced 4(p<0.05). 3. The group that used tray adhesives showed less dimensional changes(p<0.05). The findings revealed that mechanical methods of mixing alginate impression materials had little influence on dimensional changes. However, it is proven that following manufacturers instructions in alginate impression taking is an important step in acquiring accurate impressions and tray adhesives may play an important role in enhancing the results.

• 한국작물학회지
• /
• 제26권2호
• /
• pp.192-197
• /
• 1981

Alfalfa에 대한 국내분이 근유균의 유효성과 효과적인 근유균 접종방법을 밝히고져 배지상에서 이들 균주의 근유형성 및 질소고정능력을 검토한 다음 이들 균주에 3가지 종자접종방법을 적용하여 사경재배를 실시한 결과는 다음과 같다. 1. 근유균 접종에 따른 근유의 형성은 접종 2주후부터 볼 수 있었고 유묘의 생장은 대조구보다 현저히 증가되있으며 질업처리구(70ugN/ml)와 차이가 없어 두 균주는 모두 유교균주로 평가되었다. 2. 두 균주 모두 Broth-vacuum 방법으로 접종한 것은 근규의 형성은 있었으나 실험기간 중 유묘의 생장에 있어서는 무접종 대조구와 차이가 없었다. 3. Peat & lime pelleting 방법은 두 균주 모두에서 근유형성과 유묘생장을 현저히 증가시켰으나 Peat-adhesive 방법은$ A_1$ strain 에서 만 효과적이었다. 4. 근유의 무게와 지상부 건물중 그리고 근유의 무게와 근중사이에는 두 균주 모두에서 고도의 정의 상관관계가 인정되었다.

• 보존과학회지
• /
• 제34권3호
• /
• pp.157-166
• /
• 2018

본 연구에서는 아교의 접착 특성 향상을 위해 가교제(Cross-linking Agent)를 첨가하는 방법으로 젤라틴 결합력을 증대하였다. 제니핀 첨가 아교는 물성 측정, 구조 분석, 색잔류도, 용출도, 파단강도를 측정하였으며, 수분과 자외선에 대한 내수성과 내광성을 비교하였다. 연구 결과 겔강도와 점도는 제니핀 첨가량에 따라 증가하였다. 구조분석 결과, 젤라틴에서는 구조적으로 안정된 콜라겐의 3중 구조의 흡수 피크가 관찰되었다. 색잔류도 결과, 명도가 낮아지기 때문에 피막이 관찰되는 것으로 판단된다. 용출량은 $50^{\circ}C$ 증류수에서 제니핀 첨가량이 증가할수록 용출된 아교 양이 증가하였고 파단강도는 제니핀 첨가량에 따라 증가하였다. 내수성과 내광성은 제니핀 첨가에 따른 열화 전 후 양상이 나타나지 않았다. 본 연구 결과를 바탕으로 제니핀 첨가 아교의 접착 특성을 확인할 수 있었으며 아교에 적용 가능한 실험 방법을 고찰하였다. 제니핀을 첨가한 후에도 아교 고유의 특성인 유연성, 재용해성, 접착력, 경화속도가 사라지지 않고 향상되기 때문에 균질한 아교가 확보된다면 문화재 보존 및 아교 제작에 적용이 가능할 것으로 기대한다.