• Journal of electromagnetic engineering and science
• /
• v.2 no.2
• /
• pp.112-116
• /
• 2002

In this paper, the active integrated antenna(AIA) using a wideband printed dipole antenna and a balanced amplifier is designed and fabricated. The proposed active printed dipole antenna has characteristics of easy matching, wide bandwidth and higher output power To feed balanced signal to printed dipole, a Wilkinson power divider and delay lines are used. The measured result shows that, at 6 GHz center frequency, the impedance bandwidth is 22 % (VSWR < 2), 3 dB gain bandwidth is 28 %, the maximum gain is 14.77 dBi, and output power at P1 dB point is 23 dBm.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.81-82
• /
• 2007

This paper presents a WLAN band active monopole antenna which is made of a CPW-fed monopole antenna and a low noise amplifier implemented on single-layer low-temperature co-fired ceramic (LTCC) substrate. Planar active antenna measure return loss and power test. (drain voltage = 4V, gate voltage = -0.6V). The bandwidth, is 540MHz, return loss is -38dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.23-32
• /
• 2008

In the VHF range, active antennas are widely used for wideband applications due to their small size. Active antenna consists of antenna elements and amplifiers, which are directly connected to each other. Gain and noise-figure characteristics are very important for good sensitivity performance, because it is located at the front end of a receiving system. In this study, we developed an active dipole antenna with 5:1 bandwidth(100${\sim}$500 MHz), which consists of a dipole antenna and a P-HEMT amplifier. To obtain required performances, the antenna and the amplifier should be designed simultaneously. In order for that, we introduced an equivalent port concept to model the 1-port dipole antenna as an equivalent 2-port system. Using the proposed equivalent port, the performance of the active dipole antenna was simulated by the ADS. In order to measure the gain and noise-figure characteristics of the antenna, we utilized the same concept of the two-port equivalent impedance model. The measurement results for typical gain, NF and VSWR in the required frequency band were 8dBi, 9dB and 1.7:1, respectively. The radiation patterns at the principal planes were same as the typical radiation pattern of a dipole antenna. By comparing the simulation results with measured ones, it is confirmed that the proposed methods works well.

• Journal of IKEEE
• /
• v.15 no.1
• /
• pp.49-56
• /
• 2011

In this paper, a compact doppler sensor with oscillator type active antenna operating at 2.4GHz frequency band is proposed to measure the distance or speed of a moving object. The active antenna has been realized by oscillator using radiator, patch antenna, as its resonator. The oscillation frequency is shifted depending on approaching of the object, and a detection circuit discriminates the frequency deviation. The oscillator type active antenna has been designed and simulated. The prototype fabricated has a very small circular disk type of diameter 30mm and height 4.2mm. As for antenna performance, broadside radiation pattern with beamwidth of $130^{\circ}$ and oscillation frequency of 2.373GHz has been measured. Test results as a doppler sensor shows that doppler signal voltage of about 190mV has been obtained for conducting plate moving 1 meter away from the sensor. And, doppler signal voltage has been linearly increased to the ground from 4.5m height by free-falling the sensor.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1155-1164
• /
• 2011

In this paper, we proposed the transmit beam measurement method of active phased array antenna, which is installed in Korea's first developed naval medium range radar, using near-field measurement facility. The pulse-mode high power characteristics of active phased array antenna's trasmit-beam make it difficult to measure with general near-field measurement facilities where low power continuous RF signals are used. Thus, in this paper, the measurement method of active phased array antenna's transmit beam in conjunction with the near-field measurement facility, which is suitable for the high-power transmit beam measurement, and PNA-X network analyzer(Agilent Technologies), which can support pulse-mode measurement, was proposed and measured by near-field measurement techniques. And the EIRP(Effective Isotropic Radiated Power), the transmit characteristic of active phased array antenna, was measured by the near field measurement techniques and compared to numerical estimation which was nearly equal with small difference of 0.1 dB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.1
• /
• pp.6-16
• /
• 2009

For the application to the direction finding(DF) antenna for V/UHF bands, circular active array composed of 9 dipole element has been investigate. For miniaturization of the overall size array, the element has been chosen to be of the top-hat dipole type. For the broadband operation over 20-1300MHz, some number of pin diodes have been inserted in each arms of each dipole element. By employing this type of each element dipole, the effective dipole length can be increased or decreased according as the inserted pin diodes is on or off. The active array antenna has been design to be directly connected to the balanced push full amplifier such that the amplifier may play a role as a balloon and may improve the sensitivity as a receiver as well. The active array antenna has been designed and fabricated. Some experimental results have been presented in comparison with simulated results.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.5
• /
• pp.203-208
• /
• 2014

In this paper, the antenna of a small active RFID for 433MHz is proposed, and the proposed antenna is a kind of built-in antenna, which uses IFA structure. The performance was improved by the change of the spacing between the feed point and short strip, inserting the meander line structure in a radiator, and varying the gap between the radiator and the ground plane in the proposed antenna. To confirm the characteristics of the antenna parameters, HFSS from ANSYS Inc. was used for the analysis. The frequency band of 433MHz Active RFID is from 433.67 to 434.17 MHz. There is a value of return loss less than -9.54 dB in 433MHz band of the active RFID, and the maximum antenna gain is -4.28dBi. The Jig size of the proposed antenna is $72{\times}44{\times}1mm$, and the size of the antenna area is $35.5{\times}19.5mm$. The result proved the possibility of the practical use on miniaturized 433MHz antenna using IFA structure that came from comparing and analyzing the measured and simulated data of the antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.518-521
• /
• 2019

In this paper, an active antenna module operating in the 60 GHz band is designed and fabricated by combining a commercial transmitter chip and patch array antenna. The designed module is composed of an antenna PCB and a PCB with a transmitter chip. The frequency-control and bias-control signals are applied to the transmitter chip, using an Arduino kit. A baseband I/Q signal is also applied to the chip. A ring hybrid balun converts the output of the transmitter module to a single output, which is the output of the transmitter chip that outputs a differential output. The output is delivered to the $2{\times}4$ microstrip patch array antenna PCB as a micro-computer connector. The radiation pattern of the millimeter-wave signal of the final output is compared with the simulation results. The measured radiation patterns of the fabricated active antenna module confirm that the positions of the 3 dB beam width and null point agree well with the simulation results.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.6
• /
• pp.43-55
• /
• 2013

In this paper, we propose a cylindrical active phased array antenna of Beam Steering Characteristics in the horizontal plane(H-plane) and vertical plane(E-Plane) on the cylinder form array structure. We design the bent dipole antenna of the cylindrical array structure adapted excellent mutual-coupling characteristics, designed and manufactured the cylindrical array antennas and power combiner/divider unit for power dividing and combining on the antenna. The radiating elements array spacing of Cylindrical array antenna were determined to avoid grating lobes at half power beam steering. Beam steering of the antenna was implemented with 6-bit phase shifter in the transceiver and have been designed based on the characteristics the antenna beam steering at -24 degrees to 24 degrees horizontal, vertical 0 degrees to 36 degrees beam steering. A cylindrical active phased array antenna that produced for verification the performance of the antenna are measured radiation characteristics in accordance with beam steering at L-Band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.13-21
• /
• 1997

In this paper, the oscillator type active antenna used as an element of active phased array antenna is designed and fabricated using slot coupling. The radiating element and active circuit are fabricated on each layer respectively and coupled electromagnetically through slot on the ground plane. This structure can solve the problems such as narrow bandwidth of microstrip antenna, spurious radiation by active circuits, and spaces for integration of the feeding circuits which are caused by integrating antennas with oscillator circuits in the same layer. The active antenna in this paper, the oscillation frequency can be tuned linearly by controlling the drain bias voltage of FET. The frequency tuning range is between 12.37 GHz to 12.65 GHz when bias voltage is varied from 3V to 9V, thus frequency tuning bandwidth is 280 MHz (2.24%). The output power of antenna is uniform within 5dB over frequency tuning range. Therefore this active antenna can be used as an element of linear or planar active phased array antennas.