• Journal of Pharmaceutical Investigation
• /
• v.27 no.4
• /
• pp.313-321
• /
• 1997

Ion exchange resin complexes of famotidine have been prepared by the reaction of famotidine solution with activated ion exchange resins. Complex formation efficiency between famotidine and ion exchange resin was about $80{\sim}90%$ in average, calculated by HPLC determination. Drug release characteristics from the resin complexes were evaluated by the modified percolation method. Famotidine release was dependent on the type of ion exchange resins. In the case of weakly acidic resin complexes, the cumulative released amount of famotidine was more than 90% for 1hr in pH 1.2 buffer solution. However, in the case of strongly acidic resin complexes, it was less than 5% for 3hr in the same medium. Strongly acidic resins revealed some advantages over weakly, acidic resins for overcoming instability of famotidine in gastric juice. In addition, strongly acidic resin complexes showed controlled release of famotidine in pH 6.8 buffer solution, showing the result of about 60 to 70% of drug release for 5hr. After oral administrations of famotidine-resin complexes to rats as dose of 40 mg equivalent/kg, the pharmacokinetic parameters of famotidine were obtained by model independent analysis and compared with those of famotidine solution or suspension. $C_{max}$ of famotidine-resin complex was lower than that of famotidine solution or suspension. MRT, MAT, and MDT of the complexes were greater than those of famotidine solution or suspension. From these results, it was expected that famotidine was released slowly from the complexes and absorbed continuously into systemic circulation. It was recognized that drug release from the complexes was the rate-limiting step in drug absorption, since there were close correlations between in vitro drug release and in vivo pharmacokinetic parameters.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.270-270
• /
• 2012

Low temperature atmospheric pressure plasmas (APPs) have been known to be effective for living cell inactivation in the water [1]. Many earlier research found that pH level of the solution was changed from neutral to acidic after plasma treatment. The importance of the effect of acidity of the solution for cell treatments has already been reported by many experiments. In addition, several studies have demonstrated that the addition of a small amount of oxygen to pure helium results in higher sterilization efficiency of APPs [2]. However, it is not clear yet which species are key factors for the cell treatment. To find key factors, we used GMoo simulation. We elucidate the processes through which pH level in the solution is changed from neutral to acidic after plasma exposure and key components with pH and air variation with using GMoo simulation. First, pH level in a liquid solution is changed by He+ and He(21S) radicals. Second, O3 density decreases as pH level in the solution decreases and air concentration decreases. It can be a method of removing O3 that cause chest pain and damage lung tissue when the density is very high. H2O2, HO2 and NO radicals are found to be key factors for cell inactivation in the solution with pH and air variation.

• KSBB Journal
• /
• v.14 no.4
• /
• pp.389-395
• /
• 1999

Bifidobcterium spp. can provide human being with several beneficial physiological. Therefor, there has been a considerable interest in products Bifidobcterium spp. dietary supplements or as starter cultures for probiotic products that may assint in the improvement of health on the human. But indusrial applications have been limited because Bifidobcterium spp. are sensitive to acidic pH due to organic acid produced by themselves and various conditions. The objective of this study was to establish new method for improvement of Bifidobcterium viability by entrapment im calcium alginate beads. We have a plan to select the most suitable polymer through the comparison with acid tolerance oxygen tolerance and theological properties of polymer. Increase of the viable number of Bifidobcterium induced increasing acid tolerance and oxygen tolernce trough the development of entrapment technique. The 4%, 3030mm diameter) sodium alginate beads led to the best survivability under acid condition. Especially, addition of 6% mannitol, 6% glycerol or 6% sorbitol to the sodium alginate helped a beneficial effect on viability against acid, bile salt, hydrogen peroxide and cold strage. The number of viability of entrapeede cells by retreatment was 96 fold higher than non-entrapeed cells after 5 hours of storage under pH 3 acidic condition. These experimental data clearly demonstrate that a whole cell immobilization by entrapment in calcium alginate beads is an important survival mechanism enable to withstand environmental stresses as the acidic condition, hydrogen peroxide toxicity and frozen state.

• Journal of Electrochemical Science and Technology
• /
• v.1 no.2
• /
• pp.117-120
• /
• 2010

Materials used as fuel cell electrode should be light, high conductive, high surface area for reaction, catalytic surface and uniformity of porous structure. Nickel is widely used in electrode materials because it itself has catalytic properties. When used as electrode materials, nickel of only a few im on the surface may be sufficient to conduct the catalytic role. To manufacture the nickel with porous structure, Electroless nickel plating on carbon fiber be conducted. Because electroless nickel plating is possible to do uniform coating on the surface of substrate with complex shape. Acidic bath and alkaline bathe were used in electroless nickel plating bath, and pH and temperature of bath were controlled. The rate of electroless plating in alkaline bath was faster than that in acidic bath. As increasing pH and temperature, the rate of electrolee plating was increased. The content of phosphorous in nickel deposit was higher in acidic bath than that in alkaline bath. As a result, the uniform nickel deposit on porous carbon fiber was conducted.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.2
• /
• pp.9-14
• /
• 1993

Weathering of wood in a region of acid rain was performed by the test which thin veneers of Sitka spruce were exposed to outdoor weathering for a total of 18 weeks, with a daily soaking for 30 minutes in acidified water in the pH range 2~5.6. The weathering measured by weight loss and loss in maximum failure load in tension was accelerated by the increase in the acidity of acidified water and in the period of outdoor exposure. It was also shown that the weathering was accelerated even with low acidic conditions in the case of long exposure period, although the weathering was rapidly accelerated with high acidic conditions. When compared the degree of weight loss with that of loss in failure load by weathering, the latter was much greater. From the results of this research, it could be concluded that at pH 4.0 or below of precipitation, the acceleration of weathering of exterior wood would become serious problems, which would be caused deterioration in performance of exterior wood.

• KSBB Journal
• /
• v.29 no.6
• /
• pp.426-431
• /
• 2014

pH controlled batch reactor and bubble column reactors have been developed in this research. They were used to produce high concentration of GABA and to determine optimal pH for GABA production. Glutamate decarboxylase (GAD) was isolated from recombinant E. coli and used for GABA production from monosodium glutamate (MSG). pH control was inevitable because the pH increased with MSG consumption. GAD showed highest activity at acidic conditions at pH 5.5 but the optimal pH for GABA production was pH 6.0. When 1.5 mole of MSG was used as reactant, the 1.05 mole of GABA was produced after 10 hrs batch reaction. Using bubble column reactors, 80 % of MSG was converted to GABA for 6 hrs reaction and 1.2 mole of GABA was produced.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2415-2418
• /
• 2008

Polydiacetylenes (PDAs) are very attractive chemical substances which have distinctive features of color change and fluorescence emission by thermal or chemical stress. Especially, when PDAs contact with solutions of a particular pH, such as a strong alkaline sodium hydroxide (NaOH) solution or a strong acidic hydrogen chloride (HCl) solution, PDAs change their color from non-fluorescent blue to fluorescent red. In this study, we propose a novel method to detect alkaline pH using PDAs and NaOH solutions by hydrodynamic focusing on a microfluidic chip. Preliminary results indicate that the fluorescent intensity of PDAs increases in respond to the NaOH solution concentrations. Also, the fluorescence is quenched back when the PDAs are in contact with a HCl solution. These results are useful in a microfluidic PDA sensor chip design for pH detection.

• Journal of the Korean Chemical Society
• /
• v.19 no.2
• /
• pp.123-129
• /
• 1975

The rate constants of the hydrolysis of phenylvinylsulfone were determined by ultraviolet spectrophotometry at various pH and a rate equation which can be applied over wide pH range was obtained. The reaction mechanism of hydrolysis of phenylvinylsulfone and especially the catalytic contribution of hydroxide ion which did not study carefully before in acidic media, can be fully explained by the rate equation obtained. The rate equation reveals that: below pH 7, the reaction is initiated by the addition of water molecule to phenylvinylsulfone. At above pH 9, the overall rate constant is only dependent upon the concentration of hydroxide ion.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.10a
• /
• pp.335-343
• /
• 2011

We examined the effect of the acidic liquid from carbonized rice hull(ALCRH) treatments to molded fiber packages(MFP) on weight, Haugh unit, pH and microbial activity of egg to extend the shelf life in egg packaging. Higher concentration and surface spray treatment of the acidic liquid extended the shelf life of egg. ALCRH treatment to MFP improved the performance of the packaging for egg in terms of decreased weight loss and retarded microorganism growth of eggs during storage.

• Applied Biological Chemistry
• /
• v.39 no.3
• /
• pp.245-248
• /
• 1996

Thermal stability of the major color component, cyanidin 3-glucoside, isolated from Korean pigmented rice (Oryza sativa var. Suwon 415) were investigated to explore possible application of value-added natural colors as food additives. The anthocyanin showed red and blue color with maximum absorption peaks at 511 nm and 572 nm in acidic (pH 2.0) and alkaline (pH 9.0) buffer solutions, respectively, and the thermal degradation reactions were carried out with different temperature ranges at $50{\sim}95^{\circ}C$. Degree of degradation was determined with UV/Vis spectra which indicate characteristic absorption patterns with sharp isosbestic points at 350 nm (pH 2.0), and 275, 310, and 405 nm (pH 9.0). Thus the reaction follows simple first-order kinetics. The anthocyanin was very stable against heat at acidic pH and relatively stable at alkaline pH with half-life values of 50.3 hr and 0.6 hr at $70^{\circ}C$, respectively. The activation energies and Arrhenius frequency factors of the pigment were 26.9 kcal $mol^{-1}\;and\;6.0{\times}10^{11}\;s^{-1}$, at pH 2.0, and 15.2 kcal $mol^{-1}\;and\;1.4{\times}10^{6}\;s^{-1}$, pH 9.0, and respectively.