• 대한의용생체공학회:의공학회지
• /
• 제19권2호
• /
• pp.183-188
• /
• 1998

동맥과 PTFE 재료로 된 대체혈관이 혈관폐색이 생긴 부위를 우회하기 위하여 단측문합이 되었을 때 문합각의 변화에 의한 영향을 살펴보기 위하여 두 혈관의 직경비를 0.5로 고정하고 문합각을 30$^{\circ}$에서 90$^{\circ}$까지 $10^{\circ}$간격으로 변화시켜 컴플라이언스와 응력의 분포형태를 살펴보고 또한 직경비의 영향도 살펴보기 위하여 문합각을 45$^{\circ}$로 고정하고 직경비를 0.1에서 1까지 0.1간격으로 변화시켜 컴플라이언스와 응력의 변화를 살펴보았다. 단측문합비에 사용된 모델은 20-24mm, 내경 4mm, 두께 0.5mm의 동맥과 길이 10mm, 내경 2mm, 두께 0.2mm의 PTFE 대체혈관이 사용되었으며 문합각이 작아지거나 직경비가 커질수록 예각 문합부의 컴플라이언스가 점점 더 커진다는 것을 알았다.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 춘계학술대회
• /
• pp.334-337
• /
• 1997

Von Mises stress and compliance distribution was evaluated using a finite element analysis on the end-to-side anastomosis of an artery with length of $20\sim24mm$, inner diameter of 4mm, thickness of 0.5mm and a PTFE graft with length of 10mm, inner diameter of 2mm, thickness of 0.2mm when the anastomotic angle was taken from $30^{\circ}\sim90^{\circ}$ in every $10^{\circ}$ and the diameter ratio from $0.1\sim1$ in every 0.1. The inner pressure of $1330dyne/mm^2$ was applied inside the 2 conduits. It was found that the compliance whose magnitude is larger on the acute angle anastomotic side than on the acute angle side became larger as the anastomotic angle became smaller and the diameter ratio larger and that the equivalent stress on the acute angle anastomotic side was larger than that on the abtuse angle side and became larger as the anastomotic angle and the diameter ratio became larger.

• 소성∙가공
• /
• 제14권3호
• /
• pp.282-290
• /
• 2005

Nowadays, TFT-LCD is widely used as display unit of many digital devices. And, the backlight unit(BLU) is used as a light source of TFT-LCD module. In the backlight unit, the most important component is a light guide, which guides the input light to the TFT-LCD module uniformly. Recently, many researchers have focused on improving the efficiency of BLU by changing the design and structure of a light guide. In the present paper, a series of simulation was performed to find the optimal luminance distribution of emanated light from the given geometry as the first step. From the results of simulations for the light guide with given V-groove pattern, the emanated light from it is mostly affected by the groove angle. In the case of acute angle, about 74 degrees was found as optimal angle to satisfy the restrictions of angular luminance distribution, FWHM, the maximum luminance, etc. However, as far as the average luminance value was concerned, the case of 120 degrees(abtuse angle) was found to be the best while prism films were added to the BLU. As a next step the light guide samples of 74 and 120 degrees were manufactured by DSF method, which was recently proposed by the authors. Of course, most of design parameters were chosen by the aid of simulation results. Finally, the results of average luminance values were compared between the simulation and DSF molded samples.