• 한국정보통신학회논문지
• /
• 제5권5호
• /
• pp.1001-1010
• /
• 2001

TLM 법에서 이산 그린함수 흡수경계는 광대역에서 정밀한 수치해석에 사용되어왔다. 그러나 이산 그린함수 흡수경계는 이산 그린함수를 얻는 수치해석이 부가적으로 요구되기 때문에 흡수경계를 적용하는 과정이 복잡하다. 그러므로 흡수경계를 적용하는 과정의 간소화를 위해서 본 논문에서는 새로운 그린 흡수층을 제안한다. 제안된 그린 흡수층은 이산 그린함수의 손실처리 방법을 응용하여 구현하였으며 최적의 흡수 상태를 그린 흡수층의 길이에 대응하는 손실 증가율과 감쇠상수리 관계로 얻을 수 있었다. 또한 최적의 흡수상태가 되는 그린 흡수층을 적용하여 도파관 대역통과필터를 해석하였다. 그 결과, 기존의 그린함수 흡수경계와 제안된 그린 흡수층을 적용한 해석 결과가 정확히 일치하였다.

• Earthquakes and Structures
• /
• 제15권6호
• /
• pp.655-665
• /
• 2018

Shield tunnels are widely used throughout the world. However, their seismic performance has not been well studied. This paper focuses on the seismic response of a large scale model tunnel in compacted sand. A 9.3 m long, 3.7 m wide and 2.5 m high rigid box was filled with sand so as to simulate the sandy soil surrounding the tunnel. The setup was excited on a large-scale shake table. The model tunnel used was a 1:8 scaled model with a cross-sectional diameter of 900 mm. The effective shock absorbing layer (SAL) on the seismic response of the model tunnel was also investigated. The thickness of the tunnel lining is 60 mm. The earthquake motion recorded from the Kobe earthquake waves was used. The ground motions were scaled to have the same peak accelerations. A total of three peak accelerations were considered (i.e., 0.1 g, 0.2 g and 0.4 g). During the tests, the strain, acceleration and soil pressure on the surface of the tunnel were measured. In order to investigate the effect of shock absorbing layer on the dynamic response of the sand- tunnel system, two tunnel models were set up, one with and one without the shock absorbing layer of foam board were used. The results shows the longitudinal direction acceleration of the model tunnel with a shock absorbing layer were lower than those of model tunnel without the shock absorbing layer, Which indicates that the shock absorbing layer has a beneficial effect on the acceleration reduction. In addition, the shock absorbing layer has influence on the hoop strain and earth pressure of the model tunnel, this the effect of shock absorbing layer to the model tunnel will be discussed in the paper.

• 전기학회논문지
• /
• 제62권12호
• /
• pp.1725-1729
• /
• 2013

In this paper, the modeling and simulation of infrared absorption in an infrared absorbing structure with the cascaded transmission line model were carried out. Each layer in the infrared absorbing structure can be modeled as a characteristic impedance of the cascaded transmission line model. The simulation results show that the cavity thickness to get a maximum absorption should be less than a quarter wavelength, which is somewhat different from prevalent thickness. It can be assured that the sheet resistance of an absorbing layer to get a maximum absorption is $377{\Omega}/{\square}$, that the thickness of the absorbing layer dose not affect the spectral characteristics of absorption. It is also shown that the thickness of the active layer is not critical to the IR absorption. It can also be assured that the validation of this modeling is proved in comparison with the previous results from similar absorbing structures.

• Journal of Magnetics
• /
• 제3권2호
• /
• pp.64-67
• /
• 1998

Microwave absorbing properties of ferrite-epoxy composite (absorbing layer) attached on the carbon fiber polymer composite (reflective substrate) are analyzed on the basis of wave propagation theory. A modified equation for wave-impedance-matching at the front surface of absorbing layer including the effect of electrical properties of the quasi-conducting substrate is proposed. Based on this analysis, the frequency and layer dimension that produce zero-reflection can be estimated from the intrinsic material properties of the obsorbing layer and the substrate. It is demonstrated that the microwave reflectivity of carbon fiber composite has a strong influence on the microwave absorbance of front magnetic layer.

• 한국전기전자재료학회논문지
• /
• 제13권6호
• /
• pp.538-544
• /
• 2000

The laser patterning of sputter-deposited CoNdZr/Cu/CoNbZr multi-layered films had been tried using Nd:YAG laser. However generally it is very difficult to remove metal films because of their high reflectance of the laser on the surfaces. As a counterproposal for this problem authors for the first time tried to deposit energy-absorbing layers on the metal films and then irradiated the laser on the surfaces of energy-absorbing layers. Here the energy-absorbing layers consisted of laser energy-absorbing fine powders and binding polymers. Three kinds of powders for the energy-absorbing layers had been used to see the difference in the pattern formation with the degree of laser energy absorption. They were electrically conductive silver powders insulating BaTiO$_3$powder and semiconducting carbon powder. Remarkable difference in width of the formed pattern and the roughness of pattern edge were observed with the characteristic of the powder for the energy-absorbing layer. The pattern width using carbon paste was about three times larger than that using BaTiO$_3$paste. It was observed that the energy-absorbing layer with carbon was the most effective on this micro-patterning.

• 한국군사과학기술학회지
• /
• 제13권5호
• /
• pp.869-874
• /
• 2010

A research for the optimal design of microwave absorbing material featuring for the broadband has been conducted to apply to warship. A multilayered structure was suggested using wave absorbing layers and resistance layer to perform high performance in broadband frequencies. For the optimization of the wave absorbing characteristics, the thickness and permittivities of the absorbing layers as well as the surface resistance of the resistant layer were determined using genetic algorithm. The data base of permittivities related to the density of the dielectric materials and loss materials was obtained by the experiments for the dielectric constants of the absorbing layers, furthermore, the results were numerically expressed and used for the optimization.

• 지구물리와물리탐사
• /
• 제12권2호
• /
• pp.183-191
• /
• 2009

탄성파 수치 모형 계산에 있어서 널리 사용되는 엇갈린 격자 방법이 아니라 회전된 엇갈린 격자 방법을 사용하여 탄성파 수치 모사를 수행하였다. 표준 엇갈린 격자 방법에서는 특별한 자유 경계조건을 적용하여야 하는 단점이 있지만 회전된 격자 방법에서는 물성으로 진공 또는 공기층을 부여함으로써 자유 경계조건을 실현가능하다는 것을 확인할 수 있었다. 파동전파에 있어서 유한 경계 조건에서 발생하는 인공 반사파를 제거하기 위해 PML (Perfectly Matched Layer)의 파동식 분해라는 단점을 극복할 수 있고 좋은 성능을 보이는 CPML (Convolutional Perfectly Matched Layer)법을 회전된 엇갈린 격자법(RSG: Rotatged Staggered Grid)에 적용하였다. 회전된 격자 유한 차분법에서 CPML의 고주파수 흡수 특성과 에너지 흡수율 조사, Cerjan법의 감쇠를 비교한 결과 흡수경계조건으로 좋은 성능을 확인하였다. 유체와 고체의 모형에 대한 경계에 대하여서도 매우 효과적으로 경계면에서 발생하는 반사파를 제거할 수 있음을 알 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.896-901
• /
• 2002

The sound absorption coefficients for multiple layer perforated plate systems containing several compartments with airspaces and porous absorbing materials are estimated using the transfer matrix method developed in the previous paper. The absorption coefficients from transfer matrix method agree well with the values measured by the two-microphone impedance tube method for various combinations of perforated plates, airspaces or porous materials. Based on these results, a guidance for the design of multiple layer perforated plate systems combined with airspaces and porous absorbing materials is discussed in detail.

• 한국소음진동공학회논문집
• /
• 제15권5호
• /
• pp.571-577
• /
• 2005

The acoustic absorption of multiple layer perforated panel systems is largely reduced at the anti-resonance frequency. In order to improve the acoustic absorption at the anti-resonance frequency, the sound absorbing materials are inserted between perforated panels. By the insertion of absorbing materials, it is found that the multiple layer perforated panel system has better acoustic absorption at the anti-resonance frequency and more broadband frequency. Besides, it is shown that the absorption coefficients from the transfer matrix method agree well with the values measured by the two-microphone impedance tube method for various combinations of perforated panels, airspaces or sound absorbing materials.

• Composites Research
• /
• 제14권6호
• /
• pp.38-46
• /
• 2001

본 연구에서는, 전자파 흡수능을 가진 경사 복합재료 적층판를 설계할 수 있는 최적화 코드를 개발하였다. 또한, 유리 섬유/에폭시 직조 적층판, 알루미늄 첨가물을 함유간 유리섬유/에폭시 직조 적층판과 카본/에폭시 직조 적층판의 유전율을 구하고, 최적화 로드를 이용하여 3층형 전자파 흡수 복합재료 적층판을 개발하였다. 실험에 사용된 복합재료 적층판은 모두 전자기적으로 면내등방성을 가지며 따라서, 동축선과 망분석기를 이용하여 유전율을 측정하였다. 이 로드는 전자기적으로 직교이방성을 가지는 고분자기지 복합재료의 적층각을 포함한 다양한 변수를 고려할 수 있다.