• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.38-48
• /
• 1998

To apply the high chromium white cast irons for sliding parts of construction equipments, the wear characteristics of these alloys which have three kinds of microstructure(hypoeutectic, near-eutectic, hypereutectic) were investigated by dry sand/rubber wheel tester. Also, the effect of heat treatment was investigated for the same alloys. As result of the test, heat treatment have no effect on the wear characteristics. And, hypereutectic composition alloy has the highest wear resistance against SiO$_2$. Also after test, cracking was observed in eutectic and primary carbides of all materials tested. This phenomenon was important factor in the wear resistance.

• Tribology and Lubricants
• /
• 제7권2호
• /
• pp.61-66
• /
• 1991

The frictional and wear characteristics of non-asbestos friction materials made of four different fibers (carbon, aramid, ceramic and glass) have been investigated at elevated temperature using High Frequency Friction Tester. On the basis of the experimental results, friction and wear phenomena of four different non-asbestos fibers were caused by lattice layer film of carbon, polymeric transfer film of aramid, abrasion of ceramic and adhesion of glass fiber under each contact junction. The surface analysis of the worn specimens and counter parts after tests were observed using Scanning Electron Microscope and Optical Microscope.

• 치위생과학회지
• /
• 제18권3호
• /
• pp.164-171
• /
• 2018

To improve the oral health status of Korean people, it is necessary to encourage proper oral hygiene management habits, such as toothbrushing, through appropriate health promotion techniques. Therefore, the purpose of this study was to evaluate the removal of plaque and tooth abrasion using ultra-soft (filament 0.11~0.12 mm) and soft toothbrushes for toothbrushing. The plaque removal was performed using a dentiform and Arti-spray, and the Patient Hygiene Performance (PHP) index was calculated as the sum total score divided by the total number of surfaces. In the abrasivity experiment, according to the number of brushings, a micro Vickers hardness tester was used, and a sample in the range of 280~380 Vickers hardness number was selected. The number of toothbrushing stroke were 1,800 (2 months), 5,400 (6 months), 10,800 (12 months), and 21,600 (24 months). The tooth abrasion was measured using a scanning electron microscope. Statistical analysis was performed using IBM SPSS Statistics 22.0 and a p-value <0.05 was considered significant. According to the results, there was no statistically significant difference in the degree of plaque removal between ultra-soft and soft toothbrushes. The difference in tooth abrasion between before and after toothbrushing was found to be greater with the soft toothbrushes than with the ultra-soft toothbrushes. Therefore, the ultra-soft toothbrush not only lowers tooth damage by reducing tooth abrasion, but also shows a similar ability to remove plaque as soft toothbrushes.

• 한국의류학회지
• /
• 제23권6호
• /
• pp.853-863
• /
• 1999

the change of physical properties (thickness, weight, air permeability) and mechanical properties(abrasion resistance breaking load and displacement) of samples were determined after heat exposure by a RPP tester. The effect of exposure time and heat flux intensity on the changes and the relationship between physical properties and mechanical properties were investigated. FR treated cotton Kevlar/PBI and Nomex with different structureal characteristics were chosen for specimens. The changes of physical properties and mechanical properties were calculated based on their initial values before heat exposure. The longer exposure time and the high heat flux intensity the more changes of those properties. Heat flux intensity was more effective on the changes, The showed to be affected by an interplay of shrinkage and pyrolysis products loss. The changes of thickness and abrasion resistance showed to be higher for plain weave fabric and those of air permeabiliyt and breaking load and displacement for twill weave fabric. While FR treated cotton which have high RPP value experienced serious and detrimental changes after heat exposure Kevlar/PBI which has low RPP value showed no high changes. In conclusion it could be confirmed that when total performance of a protective clothing is estimated retention capability of physical and mechanical properties after heat exposure as well as RPP value must be considered.

• 한국터널지하공간학회 논문집
• /
• 제19권3호
• /
• pp.475-488
• /
• 2017

암반용 TBM 공사에서 디스크 커터의 마모도 예측은 설계 및 시공 단계에서 정확한 공사비와 공사기간을 추정하는데 중요한 요소이다. 디스크 커터 마모도 예측에 널리 사용되고 있는 방법으로는 CSM 모델, 노르웨이 NTNU 모델, Gehring 모델이 있으며, 이들 모델은 각각 세르샤 시험, NTNU 시험 결과로부터 도출된 디스크 커터의 마모지수와 수명 지수를 활용하고 있다. 세르샤 시험은 금속 핀을 이용하여 일방향으로 마모를 발생 시키기 때문에 광물 입자크기나 암석의 이방성에 따라 결과의 편차가 큰 것으로 조사되었다(SINTEF, 2013). 한편, NTNU 시험의 경우에 시료 성형을 위한 사전 작업이 필요하기 때문에 수행 완료까지 2~3일의 기간이 소요된다. 본 연구에서는 금속 디스크의 회전과 이와 직교되는 방향으로 이동하면서 양방향 마모를 발생시켜 마모시험 결과의 편차를 줄이고, NTNU 시험 대비 별도의 시료성형이 필요 없어 소요 시간을 1~2시간으로 단축할 수 있는 새로운 디스크 커터 마모도 예측시험과 이를 이용한 마모지수를 제안하였다. 제안된 마모 지수는 동일 암석을 이용한 세르샤 시험과 NTNU 시험결과와 비교하여 높은 상관관계를 갖는 것으로 나타났다. 또한 국내 외 TBM 현장의 암석 시편을 이용하여 시험결과와 현장의 실제 디스크 커터 마모량을 비교 검증하였으며, 95%의 높은 결정계수를 확인하였다. NAT 시험은 신속하게 시험 수행이 가능하고, 시험 결과로부터 제안된 마모지수가 높은 신뢰수준을 보이는 것으로 판단되어 향후 활용도가 높을 것으로 기대한다.

• 한국분말재료학회지
• /
• 제26권3호
• /
• pp.214-219
• /
• 2019

In this study, the microstructure and characterization of an overlay welding layer using Fe-based composite powders are reported. The effects of the number of passes and composition of powders on the microstructure and mechanical properties are investigated in detail. The welding wire and powders are deposited twice on a stainless-steel rod using a laser overlay welding process. The microstructure and structural characterization are performed by scanning electron microscopy and X-ray diffraction. The mechanical properties of the first and second overlay layers are analyzed through the micro-Vickers-hardness tester and abrasion wear tester. In the second overlay layer, the hardness and specific wear are approximately 840 Hv and $2.0{\times}10^{-5}mm^3/Nm$, respectively. It is suggested that the increase of the volume fractions of $(Cr,Fe)_7C_3$ and NbC phases in the second welding layer enhances the hardness and wear resistance.

• Elastomers and Composites
• /
• 제54권3호
• /
• pp.225-231
• /
• 2019

Bio-based polyester polyol was synthesized via esterification between azelaic acid and isosorbide. After esterification, bio-based polyurethanes were synthesized using polyester polyol, 1,3-propanediol as the chain extender, and 4,4'-diphenylmethane diisocyanate, in mixing ratios of 1:1:1.5, 1:1:1.8, 1:1:2, and 1:1:2.3. The bio TPU (Thermoplastic Polyurethane) samples were characterized by using FT-IR (Fourier Transform Infrared Spectroscopy), TGA (Thermal Gravimetric Analysis), DSC (Differential Scanning Calorimetry), and GPC (Gel Permeation Chromatography). The mechanical properties (tensile stress and hardness) were obtained by using UTM, a Shore A tester, and a Taber abrasion tester. The viscoelastic properties were tested by an Rubber Processing Analyzer in dynamic strain sweep and dynamic frequency test modes. The chemical resistance was tested with methanol by using the swelling test method. Based on these results, the bio TPU synthesized with the ratio of 1:1:2.3, referred to as TPU 4, showed the highest thermal decomposition temperature, the largest molecular weight, and most compact matrix structure due to the highest ratio of the hard segment in the molecular structure. It also presented the highest tensile strength, the largest elongation, and the best viscoelastic properties among the different bio TPUs synthesized herein.

• 대한치과보철학회지
• /
• 제40권2호
• /
• pp.172-183
• /
• 2002

This study is going to compare the degree of color change which occurs in the following two cases of the factors which cause the color change of extra-staining, one is during glazing by the dental technician, the other is tooth brush abrasion which makes the biggest influence on color change. To compare the degree of color change before and after glazing, a sample was made with vintage incisal porcelain No. 59 OPAL(Shofu Inc, Japan), after that it was painted with three colors of porcelain stainers, then the degree of color was measured with a spectrophometer(Model Chromaview 300, Spectoron Tech Co. Korea) after it had been treated with firing only and glazing after firing 40,000-cycle and 80,000-cycle of tooth brush abrasion test were carried out in order to simulate the brushing effect of 4 years and 8 years by using the abrasion tester. The colors were measured before the test, and after the 40,000-cycle and 80.000-cycle operations and the surfaces were examined by SEM. The results of this study were as follows ; 1. The color change before and after glazing was not great enough to have a clinical significance but the orange color was changed more significantly statistically than the blue and light brown(p<0.05). 2. In the case of the color change of stained porcelain by tooth brushing, carrying out staining and glazing with two-times firings resulted in statically less color change than one firing only(p<0.05). 3. In the case of the difference in the stainer's color, the orange color which has higher chroma was statically more sensitive than the blue color(p<0.05) 4. In the case of the color change after the 80,000-cycle abrasion, all showed color change when there was one firing and the orange stainer showed some color change with clinical significance when firings were done two times.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.375-378
• /
• 2007

Abrasive wear between piston ring face and cylinder liner is an extremely unpredictable and hard-to-reproduce phenomenon that significantly decreases engine performance. Wear by abrasion are forms of wear caused by contact between a particle and solid material. Abrasive wear is the loss of material by the passage of hard particles over a surface. From the pin-on-disk test, particle dent test and scuffing test, abrasive wear characteristics of diesel engine cylinder liner-piston ring have been investigated. Pin-on-disk test results indicate that abrasive wear resistance is not simply related to the hardness of materials, but is influenced also by the microstructure, temperature, lubricity and micro- fracture properties. In particle dent test, dent resistance stress decreases with increasing temperature. From the scuffing test by using pin-on-disk tester, scuffing mechanisms for the soft coating and hard coating were proposed and experimentally confirmed.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.520-528
• /
• 1994

An investigation was carried out to understand the effect of the amount of free silicon on the tribological properties of Si-SiC. The specimens of dense Si-SiC composites with various amount of free silicon were fabricated in the temperature of 175$0^{\circ}C$ after molding under various pressure. Wear properties were measured by ball-on-plate wear tester under the constant weight of 4 Kgf at constant sliding speed of 500 mm/sec in water. As the result, the Rockwell hardness and fracture strength of Si-SiC composites remained nearly constant up to 16.62 vol% of free silicon in the Si-SiC microstructure. The Si-SiC composites containing the free silicon of 16.62 vol% was considered to be prominent in the tribological properties, which had the friction coefficient of 0.08 and the specific wear rate of 2.4$\times$10-8$\textrm{mm}^2$Kgf-1. The analysis of the wear surface indicated the complicated processes occuring on the surface such as fine polishing, abrasion, microfracture.