• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국축산식품학회지
• /
• 제25권4호
• /
• pp.430-435
• /
• 2005

유기 셀레늄 강화 폐배지를 첨가한 실험사료는 셀레늄 농도를 건물 기준으로 0.9ppm이 되도록 첨가하여 무급여(C), 2개월(T1), 4개월(T2), 6개월(T3) 급여한 한우 거세우 채끝육의 육질에 미치는 영향을 비교한 결과, 수분함량은 $63\%$에서 $66\%$로 급여기간에 따른 유의적인 차이를 보이지 않았다. 근내 지방도와 직접적으로 관련된 지방함량도 처리구별로 약 $11.7\%$에서 $16.4\%$정도의 분포를 보였으나 처리구간 유의적 차이를 보이지 않았다(p>0.05). 단백질은 T3구가$20.8\%$로 가장 높았고, T2구가 $19.2\%$로 가장 낮은 조성을 보였다. 따라서 유기 셀레늄을 사료로서 첨가 급여할 경우 일반조성분에는 영향을 미치지 않는 것으로 나타났다. 물리적 특성에 미치는 영향을 비교한 결과, 가열 감량은 $20\~21\%$, 전단력은 $3.6\~4.4kg/inch^2$의 범위로 처리구간 유의적인 차이를 보이지 않았다. 그러나 사후 24시간 pH는 대조구와 T1구가 각각 5.52, 5.57, T2와 T3는 5.50으로 급여기간이 길어짐에 따라 낮아지는 경향을 보였다. 반면 보수력은 대조구 $59.5\%$에 비하여 시험구 T1, T2, T3가 각각 63.8, 64.4, $64.2\%$로 유의적으로 높은 경향을 보였으나(p<0.05), 급여기간에 따른 차이는 보이지 않았다(p>0.05). 관능 특성을비교한 결과로서 다즙성은 처리구간 유의적인 차이를 보이지 않았으나, 연도는 T1구와 T2구가 각각 5.30, 5.28점으로서 T3구보다 유의적으로 높았으며, 향미에서는 T2구가 다른 처리구와 대조구에 비하여 높은 결과를 보였다. 본 연구 결과 유기셀레늄 급여기간이 쇠고기의 육질에는 큰 영향을 미치지 않는 것으로 나타났다. 그러나 유기 셀레늄 급여에 의한 항산화 효과 등에 대해서는 앞으로 더 많은 연구가 이루어져야 할 것으로 사료된다.

• Tuberculosis and Respiratory Diseases
• /
• 제65권6호
• /
• pp.495-503
• /
• 2008

연구배경: 유전자의 후생적인 변화(epigenetic alteration)는 악성종양의 병인론에 있어서 유전자 변이와 동등한 위치를 점하고 있다. 특히 종양억제 유전자의 전사 촉진(promoter) 부위에 발생하는 비정상적인 메칠화(methylation)는 유전자의 발현을 침묵화(silencing)하고, 결과적으로 유전자의 기능 소실을 일으키게 된다. 저자들은 CpG island와 HpaII site를 가지고 있으며 암화 과정에 관여할 것으로 생각되는 유전자에 대하여 HpaII-MspI methylation microarray를 이용하여 새로운 종양억제 유전자를 발굴하고자 하였다. 방 법: 2005년 건양대학교 병원에서 수술한 비 소세포성 폐암 환자 10명에서 폐암조직과 상응하는 암 주변의 정상조직을 얻었으며, HpaII-MspI methylation microarray (Methyl-Scan DNA chip$^{(R)}$, Genomic tree, Inc, South Korea)를 이용하여 21개의 유전자에 대하여 DNA methylation profile을 분석하였다. 각각의 유전자에서 메칠화된 정도를 두 그룹에서 비교하였고, 정상 대조군으로 두 명의 젊고 건강한 기흉 환자에서 수술한 폐 조직에 대하여 methylation profile을 분석하였다. 결 과: 21개의 대상 유전자 중 10개의 유전자에서 폐암조직, 폐암 주변 정상 조직, 대조군에서 모두 공통적으로 과메칠화 되었고, 나머지 11개의 유전자 중 APC, AR, RAR-b, HTR1B, EPHA3, CFTR의 6개의 유전자에서 대조군에서 메칠화가 없으며, 폐암조직에서 폐암 주변 정상 조직에 비하여 더 빈번하게 과메칠화 되었다. 결 론: HTR1B, EPHA3, CFTR은 비소세포 폐암에서 후생적 변화로 발생하는 새로운 종양억제 유전자의 후보 유전자로서의 가능성이 있을 것으로 생각한다.

• The Korean Journal of Pain
• /
• 제1권1호
• /
• pp.106-119
• /
• 1988

For the relief of pain in 3 cases of whiplash syndromes (case I, II and IV) and in one of reflex sympathetic dystrophy (case III), we have carried out six intentional. total spinal blocks (TSB) which attempted two times in case I, three in case II and one in carte III whoso various symptoms were chronically unresponsive to the usual conservative treatments, and a time of cervical epidural and right suprascapular nerve block in case W whose acute symptom lasted 4 drys following the cervical injury (see fables from 1 to 9). During the 753, we have observed clinically the sequential charges of respiration, lid and pupil reflexes, body motion and consciousness. And checked the blood pressure, pulse rate and arterial Pco2. The effectiveness of those blocks has been assessed by using the Visual Analog Scale which is designed to measure the patient$\acute{s}$ subjective intensity of pain and also we have found out the sequelae following those blocks. The methods of the blocks were as the following: 1. Under the N.P.O. for 8~10 hours, the preparations of immediate cardiopulmonary resuscitation and premedication with atropine 0.5mg at thirty minutes before the TSB, it was performed by injecting the mixture of 2% mepivacaine 10 or 15ml and normal saline 10 or 5ml through No. 23 G. spinal needle into the subarachnoid space of $C_7-T_1$ interspinous region with fully flexed neck on the lateral posture. Immediately after the injection of the local anesthetic in the lateral position, the patient$\acute{s}$ were hasten to change Trendelenburg$\acute{s}$ position in order to act the drugs cephalad and to make easy controlled respiration with oxygen. 2. The cervical epidural block was done by injecting the mixture of 0.5% bupivacaine 4ml, normal saline 4ml and triamcinolone 15mg through No. 18 G. Tuohy needle into the epidural space on the same region and posture as the above without premedication.7he suprascapular nerve block was done by injecting of 0.5% bupivacaine 3ml only into the right suprascapular fossa on the sitting posture. The results were as the following: 1. The cessation of respiration was seen within 5 minutes following the subarachnoidal injection of the above 20ml mixture in 2 to 3 minutes and then soon the consciousness began to disappear. The loss of Lid and pupil reflexes noted between 5 to 10 minutes and the size of the dilated pupils was equal between 5 to 20 minutes, but the pupil of the dependent side on tile lateral position was dilated 1 to 3 minutes earlier than that of the independent. The patients had r=ever responded to any stimulations during the TSB except their heart funtion. 2. The recovery of the TSB was as the following, firstly the ankle and lower limb of the independent side began to move slightly with in 34 to 75 minutes after the injection and then that of the dependent Secondly the neck and upper limb moved 6 to 15 minutes later than the lower limb. Thirdly the self respiration began to appear between 40 to 80 minutes from the block. The lid and pupil reacted to touch and light respectively between 40 to 80 minutes but the pupil of the independent side responded earlier than that of the depends. Lastly the consciousness recovered completely between 80 to 125 minutes from the block. 3. In the cardiopulmonary function during the TSB, the blood pressure were stable except the 210/130 tory at the and block of case I. There were bradycardias between 65 to 85 minutes in case I and II but no arrythmia on the EKG. The level of the arterial Pco2 was maintained to 43~45 torr during the TSB. 4. The effectiveness of the above blocks was no pain(0%) in case IV, and light (10~20%) in case I and II but no improvement in case III. 5. The right arm weakness has been complicated as to be Injected accidently the "COLD" local anesthetic at the End block of case I.

• 구강회복응용과학지
• /
• 제28권4호
• /
• pp.359-370
• /
• 2012

근관 치료가 시행된 치아의 상당수는 많은 치질의 상실로 인하여 통상적으로 치수관 내에 포스트를 세워 유지를 얻고 코어를 제작하여 최종 보철물을 제작하는 방법으로 치료되고 있다. 포스트와 코어를 이용한 고정성 보철물의 장기적 예후를 보장하고자 하는 많은 노력에도 불구하고, 임상에서는 다양한 합병증이 관찰되고 있다. 이에 본 연구에서는 근관 치료를 받고 포스트와 코어를 시행한 치아에 제작된 고정성 보철물의 임상적 상태를 조사하여 보철 진료의 임상적 참고 자료와 연구의 기초 자료로 도움이 되고자 하였다. 1990년에서 2005년까지 부산대학교병원 치과 보철과에 내원한 환자 중 근관 치료 후 포스트와 코어를 시행하고 고정성 보철물을 치료 받은 환자를 대상으로 고정성 보철물에 연관된 임상적 상태를 조사 평가하여 다음과 같은 결과를 얻었다. 1. 전체 고정성 보철물의 추정 수명은 11.1년이었고, 평균 장착 기간은 $9.7{\pm}3.4$년이었다. 2. 나이와 성별에 따른 수명의 차이는 나타나지 않았다 (P>.05). 3. 악골에 따른 수명의 차이는 나타나지 않았으나 (P>.05), 전후방 위치에서는 전치부에서 수명이 가장 길었고 구치부, 견치를 포함하는 보철물 순으로 수명이 짧았다 (P<.05). 4. 포스트의 재료 및 방법과 고정성 보철물의 종류는 보철물의 수명에 영향을 미치지 않았으나 (P>.05), 보철물의 재료는 수명에 영향을 미쳤다(P<.05). 5. 고정성 보철물의 크기는 보철물의 수명에 영향을 미치지 않았다 (P>.05). 6. 대합치 조건별 고정성 보철물의 수명은 차이가 없었다 (P>.05). 7. 고정성 보철물의 합병증은 치아 우식증 (34.5%), 치주 질환 (25.9%), 치아 파절 (15.5%), 치수 질환 (12.1%) 순이었다. 보철물을 제거한 후 잔존 치질은 51.9%가 수복 불가능한 상태였다.

• 대한화장품학회지
• /
• 제36권2호
• /
• pp.157-165
• /
• 2010

본 연구에서는 만병초 추출물의 항산화 작용과 tyrosinase, elastase 저해 효과, 만병초 추출물 중 ethyl acetate 분획 함유 크림을 제조하고 이를 피부에 도포한 후 피부 수분 보유량, 경표피 수분 손실량을 측정하였다. 만병초 추출물의 free radical (1,1-diphenyl-2-picrylhydrazyl, DPPH) 소거활성($FSC_{50}$)은 ethyl acetate 분획에서 1.83 ${\mu}g/mL$으로 나타났다. Luminol-의존성 화학발광법을 이용한 $Fe^{3+}$-EDTA/$H_2O_2$계에서 생성된 활성산소종(reactive oxygen species, ROS)에 대한 만병초 추출물의 총 항산화능($OSC_{50}$)은 50 % EtOH extract 분획에서 0.064 ${\mu}g/mL$으로 ethyl acetate와 aglycone 분획보다 더 큰 활성을 나타내었다. 만병초 추출물에 대하여 rose-bengal로 증감된 사람 적혈구의 광용혈에 대한 억제 효과를 측정하였는데 1 ~ 10 ${\mu}g/mL$의 농도에서 농도-의존적으로 $^1O_2$으로 유도된 용혈을 억제하였다. 미백 효과 측정으로는 각각 tyrosinase의 활성 저해 효과($IC_{50}$)를 측정하였는데 ethyl acetate 분획과 aglycone 분획에서 각각 70.5 ${\mu}g/mL$, 122.40 ${\mu}g/mL$로 나타났으며 elastase의 활성 저해 효과($IC_{50}$)는 ethyl acetate 분획과 aglycone 분획이 각각 51.40 ${\mu}g/mL$, 20.73 ${\mu}g/mL$로 나타났다. 만병초 추출물 ethyl acetate 분획 함유 크림을 팔에 도포한 후 180 min 동안 30 min 간격으로 수분 보유량을 측정한 결과 placebo 크림에 비하여 만병초 추출물 함유 크림의 수분 보유량을 1 ~ 4 % 정도 증가시켰다. 또한 180 min 동안 측정한 경표피 수분 손실량은 7.7 $g/m^2h$으로 무도포(10.2 $g/m^2h$)한 부분과 placebo 크림(8.9 $g/m^2h$)과 비교했을 때 더 적은 수분 손실량을 나타내었다. 이상의 결과들은 만병초 추출물이 $^1O_2$ 혹은 다른 ROS를 소광시키거나 소거함으로써 그리고 ROS에 대항하여 세포막을 보호함으로써 생체계, 특히 태양 자외선에 노출된 피부에서 항산화제로서 작용할 수 있음을 가리킨다. 또한 만병초의 tyrosinase, elastase 저해활성, 만병초 추출물 함유 크림의 인체 시험의 결과로부터 항산화, 항노화의 기능성 화장품 소재로서의 응용 가능성이 있음을 확인하였다.

• 한국식품영양과학회지
• /
• 제46권11호
• /
• pp.1358-1365
• /
• 2017

본 연구에서는 쌀 소비 촉진방안 마련 및 머핀의 품질 향상을 위한 소재 개발을 위하여 푸코이단 홍국쌀 분말을 0%, 10%, 20%, 30% 및 50%를 첨가한 머핀의 이화학적, 관능적 특성 및 생리활성을 알아보았다. 머핀의 중량은 푸코이단 홍국쌀 분말 50% 첨가군에서 55.17 g으로 가장 높게 나타났고, 높이는 4.93~5.58 cm로 푸코이단 홍국쌀 분말의 첨가량이 증가할수록 유의적으로 감소하였다(P<0.05). 머핀의 굽기 손실률은 50% 첨가군에서 8.06%로 가장 낮게 나타나 무첨가군(8.98%)과는 유의적인 차이가 있었다(P<0.05). 머핀의 수분 함량은 27.20~28.35%로 50% 첨가군에서 가장 높게 나타났으나 모든 시료 간에 유의적인 차이가 없었고, 머핀의 pH는 8.43~8.60으로 푸코이단 홍국쌀 분말의 첨가량이 증가함에 따라 유의적으로 증가하였다(P<0.05). 머핀의 내부 색도를 측정한 결과 명도를 나타내는 L값과 황색도를 나타내는 b값은 푸코이단 홍국쌀 분말의 첨가량이 증가할수록 무첨가군에 비해 유의적으로 감소하였고(P<0.05), 적색도를 나타내는 a값은 푸코이단 홍국쌀 분말의 첨가량이 증가할수록 무첨가군에 비해 유의적으로 증가하였다(P<0.05). 머핀의 경도는 푸코이단 홍국쌀 분말 50% 첨가군에서 $158.00g/cm^2$로 가장 높게 나타나 무첨가군($126.33g/cm^2$)과는 유의적인 차이가 있었고(P<0.05), 응집성은 푸코이단 홍국쌀 분말 50% 첨가군에서 69.41%로 가장 낮게 나타났으나 무첨가군 및 10%와 20% 첨가군 사이에는 유의적인 차이가 없었다. 머핀의 탄력성은 91.67~93.03%로 30% 첨가군에서 가장 높게 나타났으나 모든 시료 간에 유의적인 차이는 없었고, 씹힘성은 50% 첨가군에서 231.05 g으로 가장 높게 나타났으나 무첨가군 및 30% 첨가군과는 유의적인 차이가 없었으며, 파쇄성은 50% 첨가군에서 21.23 kg으로 가장 높게 나타났으나 무첨가군과는 유의적인 차이가 없었다. 머핀의 관능적 특성을 측정한 결과 외관과 내부색은 무첨가군이 각각 5.63과 5.71로 가장 높게 나타났고, 향과 맛 및 조직감은 50% 첨가군에서 각각 5.17과 5.88 및 5.88로 가장 높게 나타났다. 전반적인 기호도는 50% 첨가군이 5.83으로 가장 높았고(P<0.05), 그다음으로 20% 첨가군(5.33), 30% 첨가군(5.29), 무첨가군(5.08), 10% 첨가군(4.96)의 순으로 나타났다. 머핀의 총 폴리페놀 함량은 푸코이단 홍국쌀 분말의 첨가량이 증가함에 따라 유의적으로 증가하였고(P<0.05), DPPH 라디칼 소거능 역시 푸코이단 홍국쌀 분말의 첨가량이 증가할수록 유의적으로 증가하였다(P<0.05). 이상의 결과에서와 같이 푸코이단 홍국쌀 분말의 첨가는 머핀의 기호도에 긍정적인 영향을 줄 뿐만아니라 항산화 기능이 향상된 머핀을 제조할 수 있을 것으로 판단되며 다양한 제품 개발을 위한 식품소재로서의 가능성을 확인할 수 있었다.

• 공연문화연구
• /
• 제25호
• /
• pp.253-289
• /
• 2012

다시래기는 전라남도 진도 지방에서 전승되는 상장례놀이로서, 죽음의 현장에서 새생명이 탄생한다는 생사불이(生死不二)의 메시지를 담고 있다. 더불어 많은 춤과 노래, 재담을 포함한 독특한 양식적 구조로 인해 현장 연희판에서 새로운 콘텐츠에 목말라 있던 공연문화 담당층의 주목을 끌기에 충분했다. 다시래기에 관한 많은 선행연구물들이 이들의 다시래기 재창조 작업에 커다란 도움을 주었다는 것은 불문가지의 사실이다. 그러나 이전의 연구들이 진도다시래기를 다각도로 다루어 적지 않은 성과를 이루어 내었지만 주로 학술적 접근을 통해 연행의 상징적 의미를 구명하는 데 치중한 것이 사실이다. 또한 공연요소들에 대한 접근도 대본, 노래가사, 재담, 행색, 소도구, 장단, 춤사위 등의 소개에 그쳐 정작 중요한 공연요소인 소리(창(唱))의 구체적 모습에 대한 연구가 없어 아쉬움으로 남아 있었다. 이에 본고는 다시래기 음악을 분석하고 그 음악의 성격과 특징을 악보와 함께 제시하여 공연현장의 연희실기자들에게 실질적인 도움을 주고자 하였다. 본고에서 음악분석 대상으로 삼은 소리는 가상제놀이와 거사 사당놀이에 나오는 모든 소리, 그리고 연희패의 입장 시에 부르는 상여소리로 한정하였다. 다시래기 다섯 절차 중 가상제놀이와 거사 사당놀이, 상여소리가 가장 많이 공연되기 때문이다. 수많은 공연 자료가 있지만 분석의 텍스트로는 E&E미디어에서 출반된 음반인 "진도다시래기"를 택하였다. 이는 이 음원의 녹음상태가 우수하며 무엇보다 본고에서 제시된 악보를 학습 자료로 삼아 다시래기 소리를 익히고자 하는 연희실기자들이 음원 구득과 그 활용을 용이하게 할 수 있다는 판단에서이다. 음악분석 결과, 진도다시래기에서 불리는 소리들은 대부분 꺾는 음이 있는 '미'음계를 사용한 전형적인 육자배기토리로 짜여 있었다. 그리고 '솔'음계의 남부경토리는 극히 일부분에 짧게 나타나며, 음악적 완결성은 갖추지 못하고 있는 것도 알 수 있었다. 또한 같은 상장례음악임에도 씻김굿과의 음악적 친연성은 거의 발견되지 않는데, 이는 망자를 달래서 천도하는 씻김굿과 산 자의 삶을 북돋우는 다시래기의 성격과 기능이 다른 데서 비롯된 음악적 특징이라고 생각된다. 한편 다시래기 소리 전반에 판소리 음악어법적 특징들이 보이는데, 이는 다시래기의 복원과 전승에 있어서 주도적 역할을 한 예능보유자의 과거 창극단 활동이력과 무관하지 않다고 여겨진다. 다시래기 예능 담당자의 이러한 활동이력은 다시래기 원형의 변질을 초래한 원인이 되기도 하였지만, 한편으로는 다시래기의 공연요소를 더욱 풍부하게 하여 공연현장에서 콘텐츠로 활용될 수 있는 연희적 기반을 확장시킨 결과로도 나타났다. 본고의 작업이 다시래기를 원형 삼아 죽음의 상실을 극복하고 삶의 활력을 지켜낼 미래의 진지한 현장예술가들에게 의미 있게 활용되기를 기대한다.

• 한국토양비료학회지
• /
• 제5권2호
• /
• pp.65-74
• /
• 1972

IR667의 낮은 등숙률요인(登熟率要因)을 밝히고자 재식밀도(栽植密度)와 질소수준(窒素水準)만을 달리하여 $5m^2$시멘트 pot IR667-수원(水原) 214와 진흥(振興)을 재배(栽培)하여 등숙구조(登熟構造)와 이의 생리적(生理的) 기능(機能)을 비교검토(比較檢討)하여 다음 결과(結果)를 얻었다. 1. IR667의 등숙률(登熟率)은 64로 진흥(振興)의 85보다 훨씬 낮으나 수량(收量)은 IR667이 790kg/10a로 진흥(振興)의 760kg보다 높았다. 2. 출수후(出穗後) 10일(日)의 NAR당(當) 등숙립수(登熟粒數)가 IR667은 6,490으로 진흥(振興)의 6,360보다 약간커서 IR667의 천립중(千粒重)은 29.9로 진흥(振興)의 31.2보다 적으며 NAR당(當) 총립수(總粒數)는 IR667이 10,530으로 진흥(振興)의 7,290보다 훨씬 높아 이것이 IR667의 등숙률(登熟率)이 낮은 요인(要因)이었다. 3. 투광상수(透光常數)는 IR667이 0.115로 진흥(振興)의 0.200보다 적어서 IR667이 보다 큰 등숙구조(登熟構造)를 갖게되는 장점(長點)을 보였다. 4. LAI 증가(增加)에 따른 LAI당(當) 입수(粒數)의 감소율(減少率)은 두 품종(品種)이 같았다. 5. 기초생산속도(基礎生産速度)(CGR)가 최고치(最高値)인 감계엽면적지수(監界葉面積指數)(critical leaf area index)는 IR667은 6.5이고 진흥(振興)은 5.2이며 5.2이하(以下)에서 진흥(振興)의 NAR이 IR667 보다 크다. 6. 최고수량(最高收量)을 얻을수 있는 출수기(出穗期) 최적엽면적지수(最適葉面積指數)(optimum leaf area index)는 IR667이 7.4로 진흥(振興)의 6.2보다 컸다. 출수기(出穗期) 평균엽면적지수(平均葉面積指數)는 IR667이 6.2 진흥(振興)이 4.7로 최적엽면적지수(最適葉面積指數)에 미달(未達)일 뿐 아니라 감계엽면적지수(監界葉面積指數)보다도 적었다. 7. 출당후(出糖後) 20일간(日間) LAI의 감소율(減少率)은 IR667이 크나 광합성량(光合成量)의 감소율(減少率)은 진흥(振興)이 컷다. 8. LAI가 클수록 NAR이 감소(減少)하는데 그 감소율(減少率)은 등숙(登熟)이 진행(進行)됨에 따라 진흥(振興)에서는 감소(減少)하나 IR677에서는 증가(增加) 함은 저온(低溫)에 의(依)한 광합성능(光合成能)의 저하(低下)와 호흡소모(呼吸消耗)에 기인(基因)하며 등숙적온(登熟適溫)이 IR667에서 높다는 것을 의미(意味)한다. 9. 수량(收量)-등숙률곡선(登熟率曲線)은 IR677이 진흥(振興)보다 등숙(登熟)이 수량(收量)에 미치는 영향이 적은 것으로 나타났고 이는 등숙환경(특히 기온)이 IR667에 부적(不適)한 때문으로 등숙환경(登熟環境)개선은 IR667의 최대 증수요인임을 보였다.