• Geomechanics and Engineering
• /
• 제28권1호
• /
• pp.25-33
• /
• 2022

The energy transferred on drill rods by dynamic impact mainly determines the penetration depth for in-situ tests. In this study, the dynamic response and transferred energy of drill rods are determined from the frequency of the stress waves. AW-type drill rods of lengths 1 to 3 m are prepared, and strain gauges and an accelerometer are installed at the head and tip of the connected rods. The drill rods are hung on strings, allowing free vibration, and then impacted by a pendulum hammer with fixed potential energy. Increasing the rod length L increases the wave roundtrip time (2L/c, where c is the wave velocity), and hence the transferred energy at the rod head. At the rod tip, the first velocity peak is higher than the first force peak because a large and tensile stress wave is reflected, and the transferred energy converges to zero. The resonant frequency increases with rod length in the waveforms measured by the strain gauges, and fluctuates in the waveforms measured by the accelerometer. In addition, the dynamic response and transferred energy are perturbed when the cutoff frequency is lower than 2 kHz. This study implies that the resonant frequency should be considered for the interpretation of transferred energy on drill rods.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1995년도 Proceedings of the Korea Automation Control Conference, 10th (KACC); Seoul, Korea; 23-25 Oct. 1995
• /
• pp.360-363
• /
• 1995

In this paper, we describe the composition of frequency response bands based on experimental data of plants (controlled systems) with uncertainty and nonlinearity, and the robust stability evaluation of feedback control systems. Analysis and design of control systems using the upper and lower bounds of such experimental data would be effective as a practicable method which is not heavily dependent upon mathematical models such as the transfer function. First, we present a method to composite gain characteristic bands of frequency response of cascade connected plants with uncertainty and a recurrent inequality for the composition. Next, evaluation methods of the robust stability of multi-loop control systems obtained through feedback from the output terminals and multi-loop control systems obtained through feedback into the input terminals are described. In actual control systems, experimental data of frequency responses often depends on the amplitude of input. Therefore, we present the evaluation method of the nominal value and the width of the frequency response band in such a case, and finally give numerical examples based on virtual experimental data.

• 한국지반공학회논문집
• /
• 제24권12호
• /
• pp.113-120
• /
• 2008

1차원 지반응답해석은 지반에 의한 지진동의 증폭현상을 모사하는 데 널리 사용되고 있다. 가장 널리 사용되고 있는 등가선형 지반응답해석기법은 유효변형률에 상응하는 전단탄성계수와 감쇠비를 전 주파수 영역에 일률적으로 적용하며, 진동주파수에 대한 지반 응답의 영향을 고려하지 않는다. 지반의 비선형 거동을 주파수영역에서 보다 정확하게 모사하기 위하여 진동주파수와 지반거동의 상관관계를 주파수-변형률 곡선으로써 모의하는 등가선형해석기법이 개발되었으며, 이 방법은 기존의 등가선형해석기법에 비하여 정확성을 향상시킨다고 알려져 있다. 이제까지 다양한 형상의 주파수변형률 곡선이 제안되었으며, 이들은 한결같이 해석의 정확성을 증가시킨다고 주장된 바 있다. 본 연구에서는 기존의 연구에서 제안되었건 두 개의 주파수-변형률 관계 완화곡선과 본 연구에서 새롭게 제안된 세 개의 곡선을 이용하여 주파수 의존성을 고려한 등가선형해석기법의 정확성을 검증하였다. 검증에는 세 개의 부지에서 기록된 6개의 지진파가 사용되었다. 해석결과, 완화곡선은 지반응답에 지배적인 영향을 미치는 것으로 나타났으며, 주파수 의존성을 고려한 해석은 정확성을 향상시킬수 있는 것으로 나타났다. 하지만, 모든 사례에서 가장 정확하게 응답을 예측하는 완화곡선은 없는 것으로 나타났으며, 해석사례별로 최적의 완화곡선이 다른 것으로 나타났다. 따라서, FDEL 해석 수행 시, 다양한 완화곡선을 사용해야 할 것으로 판단되며 등가선형해석과 병행해서 수행되어야 한다고 판단된다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제6권9호
• /
• pp.2218-2230
• /
• 2012

In this paper, we propose an efficient channel delay estimation method for orthogonal frequency-division multiplexing (OFDM) systems, especially over doubly-selective fading channels which are selective in both the symbol time domain and subcarrier frequency domain. For the doubly-selective fading channels in single frequency network (SFN), long and strong echoes exist and thus the conventional discrete Fourier Transform (DFT) based channel delay estimation system often fails to produce the exact channel delay profile. Based on the analysis of the discrete-time frequency response of the channel impulse response (CIR) coefficients in the DFT-based channel delay estimation system, we develop a method to effectively extract the true CIR from the aliased signals by employing a simple narrow-band low-pass filter (NB-LPF). The performance of the proposed system is verified using the COST207 TU6 SFN channel model.

• 한국소음진동공학회논문집
• /
• 제21권5호
• /
• pp.447-454
• /
• 2011

This paper reports a filtered velocity feedback(FVF) controller, which is an alternative to direct velocity feedback(DVFB) controller. The instability problems due to high frequency response under DVFB can be alleviated by the suggested FVF controller. The FVF controller is designed to filter out the unstable high frequency response. The FVF controller and the dynamics of clamped beams under forces and moments are first formulated. The effects of the design parameters(cut-off frequency, gain, and damping ratio) on the stability and the performance are then investigated. The cut-off frequency should be selected not to affect the system stability. The magnitude of the open loop transfer function(OLTF) at the cut-off frequency should be small. As increasing the gain of the FVF controller, the magnitude of the OLTF is increased, so that the closed loop response can be reduced more. The enhancement of the OLTF at the cut-off frequency is reduced but the phase behavior around the cut-off frequency is distorted, as the damping ratio is increased. The control performance is finally estimated for the clamped beam. More than 10 dB reductions in velocity response can be achieved at the modal frequencies from the first to eighth modes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.264-270
• /
• 2011

This paper reports a filtered velocity feedback (FVF) controller, which is an alternative to direct velocity feedback (DVFB) controller. The instability problems due to high frequency response under DVFB can be alleviated by the suggested FVF controller. The FVF controller is designed to filter out the unstable high frequency response. The FVF controller and the dynamics of clamped beams under forces and moments are first formulated The effects of the design parameters (cut-off frequency, gain, and damping ratio) on the stability and the performance are then investigated. The cut-off frequency should be selected not to affect the system stability. The magnitude of the open loop transfer function (OLTF) at the cut-off frequency should be small. As increasing the gain of the FVF controller, the magnitude of the OLTF is increased, so that the closed loop response can be reduced more. The enhancement of the OLTF at the cut-off frequency is reduced but the phase behavior around the cut-off frequency is distorted, as the damping ratio is increased The control performance is finally estimated for the clamped beam. More than 10dB reductions in velocity response can be achieved at the modal frequencies from the first to eighth modes.

• 한국정밀공학회지
• /
• 제17권9호
• /
• pp.122-132
• /
• 2000

A simplified modeling approach of forced vibration for occupied car seats was demonstrated by using a mathematical model presented in 'Free Vibration of Car seat and Mannequin System' nonlinear and linear equations of motions were rederived for forced vibration and the transfer function was used to calculate the frequency response function. The experimental apparatus were set up and hydraulic shaker was used to obtain the system responses. Through the tests mannequin's head had a lot of problems and the responses with a head and without a head were measured. To explore the effects of linear dampings and friction moments at the joints linear analyses were performed. New sets of linear spring and damping coefficients and torsional dampings at the joints were calculated through parameter study to match up with experimental results. Good agreement between experimental and simulation frequency response estimates were obtained both in terms of locations of resonances and system deflection shapes at resonance indicating that this is a feasible method of modeling seated occupants.

• Journal of Mechanical Science and Technology
• /
• 제19권10호
• /
• pp.1891-1901
• /
• 2005

Recently the authors tried to find damage position only using measured frequency response functions. According to their work, it seems that the algorithm is very practical since it needs only measured frequency responses while other methods require exact analytic model. But when applying the method to a real structure, it requires lots of experiment. The authors, in this time, propose a method to reduce its experimental load by detecting damage within a substructure. This method searches damages not within an entire structure but within substructures. In addition, damage severity was treated in this paper since it is worthy to know damage severity. Optimization technique is used to estimate damage level using measured responses and damage model. Two test examples, a plate and a jointed structure, are chosen to verify the suggesting method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.398-403
• /
• 2001

A simplified modeling approach of forced vibration for occupied car seats was demonstrated by using a mathematical model presented in previous paper. Nonlinear and linear equations of motions were rederived for forced vibration, and the transfer function was used to calculate the frequency response function. The experimental apparatus were set up and hydraulic shaker was used to obtain the system responses. Through the tests, mannequin's head had a lot of problems, and the responses with a head and without a head were measured. To explore the effects of linear dampings and friction moments at the joints, linear analyses were performed. New sets of linear spring and damping coefficients, and torsional dampings at the joints were calculated through parameter study to match up with experimental results. Good agreement between experimental and simulation frequency response estimates were obtained both in terms of locations of resonances and system deflection shapes at resonance, indicating that this is a feasible method of modeling seated occupants.

• 한국추진공학회지
• /
• 제24권2호
• /
• pp.83-93
• /
• 2020

압력전달시스템의 주파수응답특성의 효과 때문에 동압센서를 하드웨어에 flush 마운트 형태로 설치해야 한다. 그러나 측정을 위한 포트 주변의 협소한 조건 혹은 고온의 연소가스로부터 센서가 손상되는 것을 막기 위해 벽면 안쪽에 recess 마운트 방식을 설계하기도 한다. 압력전달시스템에서 동압 신호의 왜곡이 발생하기 때문에 동적 응답 특성을 반드시 고려해야 한다. 본 연구에서는 섭동 모델과 2차 축소 모델을 실험치와 비교하였고 주파수응답모델을 선택하기 위한 가이드라인을 제시하였다.