• Restorative Dentistry and Endodontics
• /
• 제12권1호
• /
• pp.165-169
• /
• 1986

A total of 114 extracted human mandibular 2nd molars were used to study the configuration of the floor of the chamber. The specimens were ground and the pulp chamber was examined with a magnifier and explored with sharp explorer. The study showed the shape of the pulp chamber, number of root canals, and the type of canal orifice. The results were as follows, 1. In so far as observing the shape of the pulp chamber of the teeth, 47.4% of the teeth were square, 42.9% were triangle and 9.7% were ovoid shape. 2. 35% of the samples had 2 root canal orifices, 62% had 3 root canal orifices, 3% had 4 root canal orifices. 3. 3% of the specimens showed 'H' shape, 5% showed 'Square' shape, 51% showed 'T' shape, 1% showed 'reverse-T' shape, 35% showed 'I' shape and 5% showed the specific 'C' shape.

• 한국세라믹학회지
• /
• 제56권3호
• /
• pp.277-283
• /
• 2019

We have examined minimization of the number of impurity particles by replacing the load-lock chamber materials of the chemical vapor deposition equipment through optimization of the pumping method in the deposition chamber. In order to reduce the number of impurity particles in the chamber, the load-lock spacer material was changed from monomer casting nylon to Torlon. Furthermore, we controlled the pumping speed and number of pumping ports, which resulted in a reduction in the impurity particle generation from 2.67% to 0.52%. This study revealed that the selection of the material for the parts of a chemical vapor deposition chamber can minimize particle generation, thereby presenting a method of optimization method of the chemical vapor deposition chamber.

• International Journal of Automotive Technology
• /
• 제6권2호
• /
• pp.79-85
• /
• 2005

This work is to investigate the surface heat flux and combustion characteristics of premixed propane mixture in a constant volume chamber. The experiment of heat flux and combustion characteristics of premixed propane mixture are performed with various equivalence ratio and initial pressure conditions. Based on the experimental results, it is found that the maximum instantaneous temperature is increased with the increase of initial pressure in the chamber. There are significant differences in the burning velocity of premixed propane mixture at different measuring points in the constant volume combustion chamber. A]so, the trends of temperature difference at each measuring points are similar to the burning velocity in the combustion chamber. It is concluded that the total heat loss during the combustion period is affected by the equivalence ratio and the initial condition of fuel-air mixture.

• 한국항해학회지
• /
• 제21권4호
• /
• pp.29-38
• /
• 1997

Because of the result of a large use of electronic equipments, the occupation density of microwave frequency band is highly increased, and electromagnetic environment is getting more seriously bad. It is sometimes reported that electronic machines are not normally operated on account of the influence of undesired electromagnetic wave, which often gives fatal blow to even human life and thus becomes serious social problems. OATS(Open Area Test Site) is principally used to measure EMI or examine elelctromagnetic emission. Because of various restrictions we often build semi-anechoic chamber which has the function of OATS to measure EMI or EMS other than OATS. If the difference of the site attenuation between semi-anechoic chamber and OATS is within ${\pm}3dB$, the semi-anechoic chamber is recognized as adequate facility to measure EMI or EMS. Accordingly authors evaluate and analyze site attenuation due to absorbent materials, polarization, mutual coupling effects, etc. The calculated and the measured site attenuation in semi-anechoic chamber are compared. As a result good agreement is obtained.

• Restorative Dentistry and Endodontics
• /
• 제7권1호
• /
• pp.53-57
• /
• 1981

A total of 130 extracted human maxillary second molars were used to study the configuration of the floor of the pulp chamber. The specimens were ground and the pulp chamber was examined with a magnifier and explored with sharp explorer. The study showed the shape of the pulp chamber, number of root canals, and the type of canal orifice. The results were as follows; 1. In so far as observing the shape of the pulp chamber of the teeth, 16.9% of the teeth were quadrilateral, 70.0% were triangle and 13.1% were ovoid shape. 2. 13.1% of the specimens have 4 root canal orifices. 73.9% have 3 root canal orifices, 11.5% have 2 root canal orifices and 1.5% have single orifice. 3. 13.1% of the specimens have 2 mesio-buccal canal orifices and among the teeth those have 3 canals, 20.8% show 'Y' shape, 29.1% show straight line and 23.8% show obtuse triangle shape.

• 한국가시화정보학회지
• /
• 제19권2호
• /
• pp.63-73
• /
• 2021

It is essential to accurately predict the change in water level, velocity, and flow rate for each passage of the grit chamber according to the operating conditions of the pump. In this study, VOF multiphase flow analysis was performed, and the flow characteristics of the grit chamber were predicted. As a result of simulations, the sedimentation phenomenon after the entrance of the grit chamber channel is expected to occur on the side walls. When 6 channels are used, the average speed of the channels is about 52% of the design standard, and when 4 channels are used, the value increases to 74% of the design standard. The average water level in the channels tends to decrease as the flow velocity increases, and the water level in the absorption well with a larger flow rate is maintained lower than that in the absorption well with a smaller flow rate.

• 반도체디스플레이기술학회지
• /
• 제23권1호
• /
• pp.52-55
• /
• 2024

In this paper, a state change study was conducted through Frequency Domain Reflectometry (FDR) technology for the process chamber of plasma equipment for semiconductor manufacturing. In the experiment, by direct connecting the network analyzer to the RF matcher input of the 300 mm plasma enhanced chemical vapor deposition (PECVD) chamber, S11 was measured in a situation where plasma was not applied, and the frequency domain reacting to the chamber state change was searched. Response factors to changes in the status, such as temperature, spacing of the heating chuck, internal pressure difference, and process gas supply state were confirmed. Through this, the frequency domain in which a change in the reflection value was detected through repeated experiments. The reliability of the measured micro-displacement was verified through reproducibility experiments.

• 한국전산유체공학회지
• /
• 제20권3호
• /
• pp.8-14
• /
• 2015

More and more, spaces are decreasing which satisfy multiple requirements for wind power plants. However, areas which have excellent wind resources and are free to civil complaints occupy a large space, although they are exposed to the cryogenic environment. This study conducted a thermal-fluid analysis of a cryogenic chamber for testing large wind turbine parts exposed to the cryogenic environment. The position of supply air is placed to the upper area to compare each cooling performance for each location of various outlets in mixing ventilated conditions. The study carried out CFD analysis for the chamber both with and without a test object. For the cases without the test object, the air temperature of the upper supply and down extract type chamber was cooled faster by 5-100% than the others. However, for the cases with the test object, the object temperature of upper supply and center extract on the opposite side type chamber was cooled faster by 33-132% than the others. The cooling performance by the air inside the chamber and the test object did not show the same pattern, which implicates the need to consider the cooling performance by not only the air but also the test object in the large cryogenic chamber design for testing large parts.

• 한국추진공학회지
• /
• 제16권6호
• /
• pp.92-97
• /
• 2012

발사체의 추진기관은 일반적으로 산화제와 연료를 연소실로 공급하여 추진력을 얻게 된다. 개발 중에 있는 한국형 발사체(KSLV-II) 2단 엔진의 경우 산화제로는 액체산소(Liquid Oxygen)를 사용하고 연료로는 JET-A1이 사용될 예정이다. 터보펌프 공급방식인 2단 엔진의 주요 구성은 연소기와 터보펌프, 엔진공급시스템 등으로 구성되어 있다. 액체 추진 엔진 개발을 위해서는 서브시스템인 연소기 개발이 선행되어야 하고 설계 및 제작된 연소기의 성능 검증은 연소기 연소시험설비(CCTF)에서 수행된다. 우주센터에 구축 예정인 연소기 연소시험설비에 대한 상세설계가 수행되었으며, 본 설계 결과를 기준으로 AMESim을 사용하여 산화제공급시스템에 대한 모델링을 수행하여 산화제 공급특성을 해석하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.502-506
• /
• 2012

발사체의 추진기관은 일반적으로 산화제와 연료를 연소실로 공급하여 추진력을 얻게 된다. 개발 중에 있는 한국형 발사체(KSLV-II) 2단 엔진의 경우 산화제로는 액체산소(Liquid Oxygen)를 사용하고 연료로는 JET-A1이 사용될 예정이다. 터보펌프 공급방식인 2단 엔진의 주요 구성은 연소기와 터보펌프, 엔진공급시스템 등으로 구성되어 있다. 액체 추진 엔진 개발을 위해서는 서브시스템인 연소기 개발이 선행되어야 하고 설계 및 제작된 연소기의 성능 검증은 연소기 연소시험설비(CCTF)에서 수행된다. 우주센터에 구축 예정인 연소기 연소시험설비에 대한 상세설계가 수행되었으며, 본 설계 결과를 기준으로 AMESim을 사용하여 산화제공급시스템에 대한 모델링을 수행하여 산화제 공급특성을 해석하였다.