• Progress in Medical Physics
• /
• v.16 no.2
• /
• pp.62-69
• /
• 2005

The purpose of this study has been performed to investigate the possibility of external audit program using thermoluminescence dosimetry for electron beam in korea. The TLD system consists of LiF powder, type TLD-700 read with a PCL 3 reader. In order to determine a calibration coefficient of the TLD system, the reference dosimeters are irradiated to 2 Gy in a $^{60}CO$ beam at the KFDA The irradiation is performed under reference conditions is water phantom using the IAEA standard holder for TLD of electron beam. The energy correction factor is determined for LiF powder irradiated of dose to water 2 Gy in electron beams of 6, 9, 12, 16 and 20 MeV (Varian CL 2100C). The dose is determined according to the IAEA TRS-398 and by measurement with a PTW Roos type plane-parallel chamber. The TLD for each electron energy are positioned in water at reference depth. In this study, to verify of the accuracy of dose determination by the TLD system are performed through a 'blind' TLD irradiation. The results of blind test are $2.98\%,\;3.39\%\;and\;0.01\%(1\sigma)$ at 9, 16, 20 MeV, respectively. The value generally agrees within the acceptance level of $5\%$ for electron beam. The results of this study prove the possibility of the TLD quality assurance program for electron beams. It has contributed to the improvement of clinical electron dosimetry in radiotherapy centers.

• Progress in Medical Physics
• /
• v.18 no.2
• /
• pp.87-92
• /
• 2007

A thermal neutron beam facility utilizing a typical tangential beam port for Neutron Capture Therapy was installed at the HANARO, 30 MW multi-purpose research reactor. Mixed beams with different physical characteristics and relative biological effectiveness would be emitted from the BNCT irradiation facility, so a quantitative analysis of each component of the mixed beams should be performed to determine the accurate delivered dose. Thus, various techniques were applied including the use of activation foils, TLDs and ionization chambers. All the dose measurements were perform ed with the water phantom filled with distilled water. The results of the measurement were compared with MCNP4B calculation. The thermal neutron fluxes were $1.02E9n/cm^2{\cdot}s\;and\;6.07E8n/cm^2{\cdot}s$ at 10 and 20 mm depth respectively, and the fast neutron dose rate was insignificant as 0.11 Gy/hr at 10 mm depth in water The gamma-ray dose rate was 5.10 Gy/hr at 20 mm depth in water Good agreement within 5%, has been obtained between the measured dose and the calculated dose using MCNP for neutron and gamma component and discrepancy with 14% for fast neutron flux Considering the difficulty of neutron detection, the current study support the reliability of these results and confirmed the suitability of the thermal neutron beam as a dosimetric data for BNCT clinical trials.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.18 no.6
• /
• pp.586-593
• /
• 1985

The rose bitterling, Rhodeus ocellatus (KNER) is commonly distributed in the fresh waters of Korea and Japan. On January 15, February 15, and March 18 in 1984, mature adults of rose bitterling were caught in the watercourse of Maeri, Kimhae, South Korea. The authors fertilized the eggs employing dry method in the laboratory on May 7, 16 and 25 in 1984. Hatched larvae were reared in small aquariums at $17{\sim}25.5^{\circ}C$ (average around $21.2^{\circ}C$). Mollusks, Anodonta woodiana in the gill chamber of which, rose bitterling lay eggs were caught in order to study natural spawning of the rose bitterling in the same watercourse. The eggs of this species are not adhesive and demersal. The size of the eggs varies from 2.54 to 2.75mm in long diameter and 1.45 to 1.65mm in short diameter. The eggs are cylindrical in form when they are extruded from ovipositor, immediately after entering water, but they acquire their distinctive form of a greatly elongated pear. Hatching took place in ca. 39 hours after fertilization. The newly hatched larvae were $2.65{\sim}2.70mm$ in total length possessing yolk sac and 13-14 myotomes. Thirteen days after hatching, the prelarvae attained 6.5 mm in total length, and the first melanophores appeared on the head, and the anterior part and sides of the yolk sac. One month after hatching, the postlarvae attained 8.5mm. in total length and emerged from the gills of the mollusks. Then the yolk sac was completely resorbed. Two months after hatching, the rose bitterling attained 14.4mm in total length, and entered the fingerling period of life. All the rays already present were the D. III, 11-12, A. III, 11-12, P. 10, V. 7. and a distinguishing, feature is the presence of a black pigment spot in the lobe of the dorsal fin.

• Journal of radiological science and technology
• /
• v.35 no.4
• /
• pp.299-308
• /
• 2012

To perform patient dose surveys in major interventional radiography procedures as a mean of inter-institutional comparison and of establishing reference dose levels with the ultimate goal of optimizing patient doses in the field of interventional radiography. We reviewed international patient dose survey data in the literature and measured patient dose in major interventional radiography procedures (TACE, AVF, PTBD, TFCA, GDC embolization). ESD(Entrance Skin Dose) was measured using TLD chips attached to the patient skin and ED(Effective Dose) was calculated using angiography unit-derived DAP. A survey of patient dose in interventional radiography procedures were also performed with a questionnaire for interventional radiologists and we proposed a guideline for optimizing patient doses in the field of interventional radiology. The patient dose survey data in interventional radiography procedures were very rare in literature compared with those in diagnostic radiography procedures. In TACE, the mean ED was 25.43 mSv and the mean ESD was 511.75 mGy. The mean ED of TACE was not high, but the cumulative dose should be checked, due to longer procedure TACE. In TFCA, the mean ED was 22.6 mSv and it was relatively high compared with data of other countries. In GDC embolization, the mean ED was not available, because GDC embolization was performed with old Image-Intensifier-type unit and there has no unit-installed ionization chamber. Also, the mean ESD of GDC embolization was up to 2,264 mGy and further studies are needed to calculate the net ED of GDC embolization. Patient dose occurred during interventional radiography procedures are high related with the difficulty of the procedure, fluoroscopy time, the number of angiographies and the treatment protocol. Therefore, continuous education and efforts should be made to optimize the patient dose in the field of interventional radiology.

• Korean journal of applied entomology
• /
• v.36 no.1
• /
• pp.77-82
• /
• 1997

This study was carried out to investigate the developmental characteristics and life cycle of sciarid fly (Lycoriella sp.), an important mushroom pest. The sciarid fly was reared ina growth chamber at 21$\pm$$1^{\circ}C$ and 55$\pm$5% of relative humidity with a 16h high, 8h dark cycle and Flammulina velutipes was used at diet. The egg was oval with 0.17 mm in diameter and 0.27 mm in length. Average egg period was 4 days. Body length of each instar from the 1st to 3rd was 0.7, 1.5, and 4.5, mm. respectively. Average weight of each instar was 1.9, 15.4 and 93.6 $\mu\textrm{g}$, respectively. In the 4th instar larvae, however, developmental characteristics of female and male became different by body length, weight and segment size. Body length and weight of the 4th instar female larvae were 5 mm and 162$\mu\textrm{g}$, and those of the male larvae were 3.5 mm and 90 $\mu\textrm{g}$, respectively. The larval periods of female and male were respectively 13.5 and13 days. Pupal length of female and male was 3.5 and 2.7 mm, and average weight was 136 $\mu\textrm{g}$ and 6.5$\mu\textrm{g}$, respectively. Adults were emerged from female and male pupae on 5.5 and on 5 days after pupation, respectively. Average longevity of male and female were 7 and 5 days, respectively. The weight of female was two-fold heavier than the male. After copulation, female laid approximately 130 to 150 eggs on/in the sporophore of mushroom. In conclusion, total lifespan of male and female were 29 and 28 days, respectively.

• Progress in Medical Physics
• /
• v.9 no.2
• /
• pp.77-88
• /
• 1998

Wedge shaped isodoses are desired in a number of clinical situations. Hard wedge filters have provided nominal angled isodoses with dosimetric consequences of beam hardening, increased peripheral dosing, nonidealized gradients at deep depths along with the practical consequendes of filter handling and placement problems. Dynamic wedging uses a combination of a moving collimator and changing monitor dose to achieve angled isodoses. The segmented treatment tables(STT) that monitor unit setting by every distance of moving collimator, was induced by numerical formular. The characteristics of dynamic wedge by STT compared with real dosimetry. Methods and Materials : The accelerator CLINAC 2100C/D at Yonsei Cancer Center has two photon energies (6MV and 10MV), currently with dynamic wedge angles of 15$^{\circ}$, 30$^{\circ}$, 45$^{\circ}$ and 60$^{\circ}$. The segmented treatment tables(STT) that drive the collimator in concert with a changing monitor unit are unique for field sizes ranging from 4.0cm to 20.0cm in 0.5cm steps. Transmission wedge factors were measured for each STT with an standard ion chamber. Isodose profiles, isodose curves, percentage depth dose for dynamic wedge filters were measured with film dosimetry. Dynamic wedge angle by STT was well coincident with film dosimetry. Percent depth doses were found to be closer to open field but more shallow than hard wedge filter. The wedge transmission factor were decreased by increased the wedge angle and more higher than hard wedge filters. Dynamic wedging probided more consistent gradients across the field compared with hard wedge filters. Dynamic wedging has practical and dosimetric advantages over hard filters for rapid setup and keeping from table collisions. Dynamic wedge filters are positive replacement for hard filters and introduction of dynamic conformal radiotherapy and intensity modulation radiotherapy in a future.

• Horticultural Science & Technology
• /
• v.31 no.1
• /
• pp.56-64
• /
• 2013

Recent unusual weather due to global warming causes shortage of daily sunlight and constitutes one of the primary reasons for agricultural damages. LED light sources are frequently utilized to compensate for the shortage of sunlight in greenhouse agriculture. The present study is aimed at evaluating formations of phytochemicals as well as growth characteristics of mature strawberry fruits ('Daewang' cultivar) during cultivation in a closed growth chamber equipped with artificial LED light as a sole light source. Each LED light of blue (448 nm), red (634 and 661 nm) or mixed blue plus red (blue:red = 3:7) was separately supplied and the intensity of each light was adjusted to $200{\pm}1{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ at plant level with a photoperiod consisted of 16 hours light and 8 hours darkness. Strawberries grown under mixed LED light of blue and red wavelengths showed a higher production of fruits than those grown under other LED treatments. Fructose, one of the free sugars, increased in mixed LED light-grown fruits. Anthocyanin contents were elevated remarkably in the mixed LED light-grown fruits compared with those in other LED treatments. Contrastingly, contents of total phenolics and flavonoids were not of much different from one another among the fruits treated with various LED lights. On the other hand, ripening of strawberry fruits was found to be faster when grown under blue LED light compared with other LED treatments. Moreover, antioxidant activities of blue or red LED light-grown fruits, respectively, were significantly higher than those of mixed LED light-grown fruits. We suggest that when daylight is in shortage during cultivation in a greenhouse, supplementation of sunlight with LED light, which is composed of blue and red wavelengths, could be useful for the enhancement of productivity as well as of free sugar content in strawberry fruits. In addition, for the strawberry culture in the plant factory, selective adoption of LED light wavelength would be required to accomplish the purpose of controlling fruit maturation time as well as of enhancing contents of sugars and antioxidants of fruits.

• Korean Journal of Heritage: History & Science
• /
• v.50 no.1
• /
• pp.42-57
• /
• 2017

The Joseon Dynasty (1392~1910) had a long tradition of making official seals to commemorate the granting of official royal titles, including posthumous honorary titles, to its kings, queens, crown princes and queen dowagers. These royal seals were typically gold-plated or made of jade. After the death of its holder, each seal would be stored in the royal seal depository in the Royal Ancestral Shrine. Extensive efforts were made to restore the traditions and culture of the royal family of Joseon during the reign of King Sukjong (r. 1674~1720). In 1705, discussions were held about the royal ceremonial objects, including the royal seals, stored in the Royal Ancestral Shrine, resulting in the reproduction of a set of accessories related with the storage of royal seals and ten golden royal seals which had been lost during wars or had yet to be made. With these reproductions, each shrine chamber of the Royal Ancestral Shrine would have had at least one seal. The details of the reproduction project were meticulously recorded in The Royal Protocol by the Directorate for the Restoration of Golden Royal Seals("金寶改造都監儀軌"). Given that the restoration project was the single event that led to the reproduction of all the golden royal seals, it is reasonable to conclude that the directorate had fulfilled a historically significant function. In this study, the main discussion is focused on the establishment of the directorate and the storage and management of the damaged royal seals. The discussion includes the manufacturing process of the golden seals, for which The Royal Protocol is compared with other similar documents in order to gain more detailed knowledge of the measurements of the turtle knob, the lost-wax casting technique, the gold plating with mercury amalgamation technique, and other ornamentation techniques. The discussion also covers the activities of the artisans who made the royal seals, based on a study of the royal protocols; the styles of the artifacts, based on an examination of the remaining examples; and the techniques used by the Directorate for the Restoration of Golden Royal Seals to produce the royal seals in 1705.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.2
• /
• pp.31-40
• /
• 2019

In Korea, 51,013 thousand tons of livestock manure was generated in 2018. A total of 46,530 thousand tons, which is 91.2% of the total amount of livestock manure generated, was treated by composting(40,647 thousand tons) or liquid fertilization(5,884 thousand tons) method. At present, the policy of livestock manure treatment in Korea is to make livestock manure into organic fertilizer(compost, liquid fertilizer) and then to applicate it on agricultural land. And this policy is very effective in terms of livestock manure treatment and nutrient recycling. However, considering the steadily declining farmland area for decades, the use of livestock manure compost could be limited in the future. There is also concern that local nutrient overloading, nutrient management regulation, and restrictions on the number of livestock may become serious problem for livestock manure treatment. In addition, there are some opinions that nutrient derived from livestock manure may flow into tributaries of major dams. In recent years, there has been a suspicion that fine dust may be generated from livestock manure compost. In recent years, the use of livestock manure fertilizer has been rapidly increasing, there is a growing demand of the development of new technologies for livestock manure treatment. Especially, cow excretes a larger amount of manure than other livestock, so that the efficiency of development of new technology for cow manure treatment will be high. Therefore, in this study, the combustion characteristics of cow manure pellet were investigated in order to analyzed whether cow manure could be used as source of solid fuel. During the combustion test, the weight loss of the cow manure pellet began to increase when the temperature of the combustion chamber reached $300^{\circ}C$. The ratio of $H_2$, $CH_4$, CO in the pyrolysis gas produced in the pyrolysis process of cow manure pellet were 6.65~11.62%, 0.58~1.54 and 11.47~14.07%, respectively.

• Korean Journal of Heritage: History & Science
• /
• v.56 no.3
• /
• pp.214-232
• /
• 2023

Stromatolite at the Daegu Catholic University, Gyeongsan was designated as a natural monument in December 2009 because it was very excellent in terms of rarity, accessibility, preservation and scale. From the time of designation, the necessity of confirming the lateral extension of the stromatolite beds with the excavation of the surrounding area, and preparing a preservation plan was raised. Accordingly, the Cultural Heritage Administration conducted an investigation of the scale, production pattern, and weathering state of stromatolites with an excavation from April to December 2022, and based on this, suggested natural heritage values and conservation and use plans. The excavation was carried out in a 1,186m² area surrounding the exposed hemispherical stromatolite (approximately 30m2). Stromatolites are continuously distributed over the entire excavation area, and hemispherical stromatolites predominate in the eastern region, and the distribution and size of hemispherical domes tend to decrease toward the west. These characteristics are interpreted as a result of long-term growth in large-scale lakes, where stratiform or small columnar domes continued to grow and connect with each other, finally forming large domes. Consequently, large and small domes were distributed on the bedding plane in clusters like coral reefs. The growth of plants and lichens, as well as small-scale faults and joints developed on the stromatolite bedding surface, is the main cause of accelerated weathering. However, preservation treatment with chemicals as with dinosaur footprints or dinosaur egg fossil sites is not suitable due to the characteristics of stromatolites, and preservation with the installation of closed protection facilities should be considered. This excavation confirmed that the distribution, size and value of stromatolites are much larger and higher than at the time of designation as a natural monument. Therefore, additional excavation of areas by experts that could not be excavated due to the discovery of buried cultural properties (stone chamber tombs) and reexamination of the expansion designation of natural monuments are required.