• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.203-212
• /
• 2005

Cellulose insulation is primarily manufactured from recycled newsprint and treated with fire retardants for the fire resistance. Thanks to the fire retardants, it is not combustible and flammable. In addition to that, Its thermal resistance is much better than that of fiberglass or rock wool. It is made from waste paper and easily decayed when it is demolished, and it has small embodied energy. So it is very environment-friendly building material. For broader use of cellulose insulation in buildings in Korea, it is necessary to test its physical performance to compare the results with the requirements on the Korean Building Code. To this end, apparent thermal conductivity (ka) measurements of Korean-made loose-fill cellulose insulations were recently completed using equipment that was built and operated in accordance with ASTM C 518 and the fire resistance was tested in accordance with ASTM C 1485. Korean loose-fill cellulose has thermal conductivity about 5% greater than the corresponding U.S. product at the same density. This is likely due to differences in the recycled material being used. Both spray-applied and loose-fill cellulose insulation lose about 1.5% of their thermal resistivity for $5.5^{\circ}C$ increase in temperature. The fire resistance of cellulose insulation is increased in linear proportion to the increase of the rate of fire retardant. Thanks to the high fire resistance, cellulose insulation can be used as a substitution of Styrofoam or Urethane foam which is combustible. The thermal conductivity of cellulose insulation was $0.037-0.043W/m{\cdot}K$ at the mean specimen temperature from $4-43^{\circ}C$. It corresponds to the thermal resistance of "Na Grade" according to the Korean Building Code. The effect of chemical content on thermal conductivity was negligible for all but the chemical-free specimen which had the highest value for the thermal conductivity over the temperature range tested. The thermal resistance of cellulose insulation is better than that of fiberglass or rock wool, and its fire resistance is higher than that of Styrofoam or Urethane foam. Therefore it can be substituted for those above considering its physical performance. Cellulose insulation is no more expensive than Styrofoam or rock wool, so it is recommended to use it more widely in Korea.

• Journal of dental hygiene science
• /
• v.13 no.3
• /
• pp.330-338
• /
• 2013

In order to explore microleakage in class V cavity based on different kinds of several dentin adhesive and composite resin, 2 kinds of composite resin was restored and exposed after applying 4 kinds of dentin adhesives. Deposited in methylene blue solution for 4 hours and cut in parallel with tooth longitudinal axis. By observing dye penetration level of enamel and dentin margins of each restored resin following conclusion was obtained. 1. In composite resin Filtek Z350XT Universal (3M/ESPE Dental Products, USA) in enamel margin, Easy Bond (3M/ESPE Dental Products) showed the lowest microleakage and this leakage was represented to be high in the order of Single Bond 2 (3M/ESPE Dental Products), Scotchbond Multi-Purpose (3M/ESPE Dental Products) and Cearfil SE Bond (Kuraray Medical Inc., Japan). In case of Filtek Z350XT Flowable (3M/ESPE Dental Products), Scotchbond Multi-Purpose showed the lowest microleakage and this leakage was represented to be high in the order of Single Bond 2, Clearfil SE Bond and Easy Bond. 2. In case of Filtek Z350XT Universal in dentin margin, Easy Bond showed the lowest microleakage and this leakage was represented to be high in the order of Scotchbond Multi-Purpose, Single Bond 2 and Clearfil SE Bond. In case of Filtek Z350XT Flowable, Scotchbond Multi-Purpose and Single Bond showed the lowest microleakage and this leakage was represented to be high in the order of Clearfil SE Bond and Easy Bond. 3. In all the groups excepting S-U group (Single Bond 2+Filtek Z350XT Universal), enamel margin showed more higher microleakage than that of dentin margin. 4. There was a difference between enamel and dentin margin among each group but it was not significant statistically (p>0.05). When summarizing this result, it is considered that composite resin and dentin adhesive could be applied selectively and particularly in case of applying 1-step self-etching dentin adhesive, this method would be advantageous for manipulation convenience and shortening of operation time.

• Korean Journal of Microbiology
• /
• v.41 no.1
• /
• pp.38-46
• /
• 2005

To determine the actual hygienic status of domestic chicken meats sold in public markets (conventional markets and department stores), microbial contamination levels (Total cells, Coliforms and Staphylococcal cells) and zoonotic pathogens (Salmonella species, Campylobacter species, Listeria species, and Staphylococcus aureus) isolation tests were conducted. Chicken meats and eggs tested were collected from the conventional markets (Si-Jang) and department-stores located in Seoul and Kyung-gi regions in 1996. In total cells and coliforms contamination tests, chicken meats sold in department stores were much lesser contamination status than those of Si-Jang, but staphylococcal cells level was much more higher than that of conventional markets. Salmonella isolation frequency was investigated as $68.8\%$, but Campylobacter jejuni and Listeria monocytogenes isolation frequency were appeared both $64.0\%\;and\;63.3\%$. In case of eggs sold in public markets, one of S. gallinarum strain $(0.7\%)$ was isolated only on the egg-shell part among the four-hundred and fourty-six. In comparison with foreign imported chicken meats, there were no big differences in microbial contamination status. On the other hand, both Salmonella and L. monocytogenes were isolated only in the chicken wings from Korea and China, but not from U.S.A. This data suggest that more hygienic control system in order to produce the safe and hygienic chicken meats and eggs is need in our country as soon as possible.

• Korean journal of applied entomology
• /
• v.30 no.1
• /
• pp.18-28
• /
• 1991

The optimal pH of the extraction buffer was 7.5 considiering AChE stability and its buffer capacity when AChE was isolated and extracted from the housefly(Musca domesitca L.)and three other insect species with 0.01 M sodium phosphate buffer. Also, the optimal pH of the reaction buffer was 7.5 considering enzyme activity and its buffer capacity when AChE activity was measured with the substrate in 0.1 M sodium phosphate buffer. The Potter Elvehjem type homogenizer with Teflon pestle was used to homgenize the tissues. When preparing a AChE suspension by centrifuging the homogenate, 700 g supernatant of adult head for the housefly, 700 g supernatnat of 5th instar nymphal whole body for the brown planthopper, lipid-eliminated 10,000 g supernatant of 5th instar larval whole body for the diamondback moth, and 700 g supernatant of 4th instar larval head for the tobacco cutworm were considered satisfactory as enzyme sources in view of mass preparation, extraction efficiency and stability of enzyme activity during evaluation. When AChE suspensions of 4 insect species were stored at $-18^{\circ}C$, more than 90% of activity was maintained up to 3 weeks. Km values of AChEs of the housefly, the brown planthopper, and the diamondback moth were 0.042, 0.037 and 0.043 mM, respectively and AChE-specific substrate inhibition was observed at high concentration. Km value of the tobacco cutworm ChE was 1.15 mM and BuChE characteristics was observed, though further study is needed. The optimal substrate concentration for the AChE inhibition tests was 0.5 mM for the housfly, the brown planthopper, and the diamondback moth and 12 mM for the tobacco cutworm.

• Journal of the Korean Chemical Society
• /
• v.35 no.4
• /
• pp.316-323
• /
• 1991

We calculated a difference between the YBa$_2Cu _3O_{7-x}$ superconductor (123 system) of critical temperature, 95 K and the YBa$_2Cu_4 O_8$ superconductors (124 system) of critical temperature, 80 K in Y-system superconductors using Extended Huckel Theory (EHT). The valence electron population (VEP), reduced overlap population (ROP) and net charge for the charged cluster models relating to the layer and the chain in 123 and 124 systems were compared. The VEPs of Cu atom in the layer of 123 and 124 systems populated d$_{z^2}$ orbital more than d$_{x^2-y^2}$ orbital, and in the chain of 123 and 124 systems populated d$_{y^2-z^2}$ orbital more than d$_{z^2}$ orbital. The ROP of the Cu(1)-O(1) in the layer of 123 system was larger than the value of the Cu(1)-O(2), but the ROP of the Cu(1)-O(2) in the layer of 124 system was larger than the value of the Cu(1)-O(1). The ROP of Cu(2)-O(4) in the chain of 123 and 124 systems were larger than the value of the Cu(2)-O(3). In 123 system the net charge values of the Cu in the layer was larger than the value of the Cu in the chain. However, in 124 system the net charge value of the Cu in the chain was larger than the value in the layer.

• Journal of Aquaculture
• /
• v.13 no.2
• /
• pp.169-174
• /
• 2000

Reproductive cycle of U. unicinctus was studied from September 1998 to August 1999, using gonadosomatic index (CSI) as an indicator. In November, the CSI values were maximum for male (6.2) and female (7.0), respectively; the values were lowest for them (1.0 and 0.5) during the successive february. Subsequently, they rapidly increased and attained peak by March-April. The values decreased again in both sexes and remained unchanged until August. The index increased in October to attain the peak by November. The CSI values clearly indicated that there are two spawning events in a year, namely the first one during April-May and the second one in December. Reproductive cycle was classified into the following successive stages: in female, multipication (January~February, June ~Setember), maturation (March~April, November), spent (May and December), degeneration and resting (June and January), and in male, multiplication January ~ february, June ~September), maturation (March~April, October~November), spent (May and December) and degeneration and resting (January and June). Histological observations revealed that oocytes in the ovary matured simultaneously in November and March. At the same time, the envelopes of matured testis became thinner than those in the early stage.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.4
• /
• pp.337-349
• /
• 2008

Despite an improved bone reactions of Mg-incorporated implants in the animals, little yet has been carried out by the experimental investigations in functional loading conditions. This study investigated the clinical and histologic parameters of osseointegrated Mg-incorporated implants in delayed loading conditions. A total of 36 solid screw implants (diameter 3.75 mm, length 10mm) were placed in the mandibles of 6 beagle dogs. Test groups included 18 Mg-incorporated implants. Turned titanium Implants served as control. Gold crowns were inserted 3 months. Radiographic assessments and stabilitytests were performed at the time of fixture installation, $2^{nd}$ stage surgery, 1 and 3 months after loading. Histological observations and morphometrical measurements were also performed. Of 36 implants, 32 displayed no discernible mobility, corresponding to successful clinical function. There was no statistically significant difference between test implants and controls in marginal bone levels (p=0.413) and RFA values. The mean BIC % in the Mg-implants was $54.4{\pm}20.2%$. The mean BIC % in the turned implant was $48.9{\pm}8.0%$. These differences between the Mg-implant and control implant were not statistically significant (P=0.264). In the limitation of this study, bone-to-implant contact (BIC) and bone area of Mg-incorporated oxidized implant were similar to machine-turned implant. The stability analysis showed no significantly different ISQ values and marginal bone loss between two groups. Considering time-dependent bone responses of Mg-implant, it seems that Mg-implants enhanced bone responses in early loading conditions and osseointegrated similarly to cp Ti implants in delayed loading conditions. However, further investigations are necessary to obtain long-term bone response of the Mg-implant in human.

• Clinical and Experimental Reproductive Medicine
• /
• v.34 no.2
• /
• pp.87-94
• /
• 2007

Objective: To examine determinants of successful pregnancy and evaluate COH-IVF outcomes of infertile patients after conservative surgical treatment of borderline ovarian tumor (BOT). Methods: In women of BOT (n=93), from January 1995 to December 1999, 44 of 93 women underwent conservative surgical treatment. From theses 44 women, patients characteristics, surgical and histological parameters were compared between 14 women who conceived and 30 women who failed to conceive. For 5 infertile women of 30 women who failed to conceive, 10 attempt IVF cycles were analysed; clinical pregnancy rate (CPR), implantation rate (IR) and live birth rate (LBR). Results: Women who conceived tend to be younger (25.9 vs 27.0 years) and lower serum CA-125 level (59.7 vs 72.9) compared to women who failed to conceive without significant difference. For 8 cycles out of 10 attempt IVF cycles, except for 2 cancellation cycles, the mean number of oocytes retrieved was 5.6 (range 2$\sim$16) with a mean fertilization rate of 74.4%. The CPR, IR and LBR per embryo transfer were 50.0% (4/8 cycles), 31.6% (6/19) and 50.0% (4/8 cycles) respectively. During the mean follow-up period after COH-IVF initiation, 29.6 (range 14$\sim$61) months, no recurrence was found. Conclusion: No determinant of successful pregnancy was found after conservative treatment for BOT. COH-IVF may be considered for infertile patients after conservative treatment of BOT. However, larger clinical studies with longer follow-up are necessary to evaluate the safety and efficacy of COH-IVF. All patients should be informed of the potential risks associated with ovarian hyperstimulation and close follow-up is necessary after COH-IVF.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.12
• /
• pp.5684-5691
• /
• 2011

The purpose of this study is to examine effects of constraint-induced movement therapy(CIMT) and/or cognitive-perceptual training(CPT) on the change of hand function in cerebrovascular accident(CVA) patients and to evaluate the change in the amount and quality of use of the affected upper extremity in performing daily living tasks. The subjects of study were 10 patients who had been under rehabilitation for more than three months after CVA onset. They were all determined as mild cognition impairment according to NCSE or MVPT test. For CIMT group, to restrict the movement of the unaffected hand the subjects had been worn modified resting arm-splint in daytime for 4 weeks. For CIMT+CPT group, the subjects were performed CPT with CIMT and control group had been under conventional occupational therapy for the same period. CIMT+CPT group showed significant improvement in simulated feeding, lifting large light objects, and lifting large heavy objects of Jebsen-Taylor Hand Function Test. CIMT group also showed significant improvement compared with control group. The mean changes of the amount of use(AOU) of the affected arm had a statistically significant difference among groups (p<.05). While CIMT+CPT group had the biggest change in the quality of movement(QOM) of upper extremity of the affected side, CTL group showed the smallest change. Both CIMT and CIMT+CPT groups had statistically significant difference in the change in the quality of movement in upper extremity of affected side with CTL group(p<.05), but there was not significant difference between CIMT group and CIMT+CPT group. CIMT performed to the patients of stroke, with mild impairment in cognitive perceptual abilities showed the improvement in hand movement and AOU and QOM of upper extremity in the affected side and the combination of CIMT with CPT showed synergic effects.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.10
• /
• pp.916-927
• /
• 2010

In general water treatment process, the disinfection process by chlorine is used to prevent water borne disease and microbial regrowth in water distribution system. Because chlorines were reacted with organic matter, carcinogens such as disinfection by-products (DBPs) were produced in drinking water. Therefore, a suitable injection of chlorine is need to decrease DBPs. Rechlorination in water pipelines or reservoirs are recently increased to secure the residual chlorine in the end of water pipelines. EPANET 2.0 developed by the U.S. Environmental Protection Agency (EPA) is used to compute the optimal chlorine injection in water treatment plant and to predict the dosage of rechlorination into water distribution system. The bulk decay constant ($k_{bulk}$) was drawn by bottle test and the wall decay constant ($k_{wall}$) was derived from using systermatic analysis method for water quality modeling in target region. In order to predict water quality based on hydraulic analysis model, residual chlorine concentration was forecasted in water distribution system. The formation of DBPs such as trihalomethanes (THMs) was verified with chlorine dosage in lab-scale test. The bulk decay constant ($k_{bulk}$) was rapidly decreased with increasing temperature in the early time. In the case of 25 degrees celsius, the bulk decay constant ($k_{bulk}$) decreased over half after 25 hours later. In this study, there were able to calculate about optimal rechlorine dosage and select on profitable sites in the network map.