• Korean Journal of Materials Research
• /
• v.24 no.12
• /
• pp.652-657
• /
• 2014

The purpose of this study was to investigate the microstructures and mechanical properties of zirconia toughened alumina (ZTA) ceramics prepared from two kinds of 3Y-TZP powders. ZTA composites were prepared by adding two kinds of 3Y-TZP powders, 3YEH (BET = $7m^2/g$) and 3YEM (BET = $16m^2/g$), to ${\alpha}$-alumina in the range of 5-25 wt%. It was found that the microstructure photographs of the ZTA composites showed that the average grain size of alumina decreased as the content of zirconia increased. In our present study, specimens containing 3YEM zirconia exhibited smaller grain sizes compared to those of 3YEH zirconia. The Vickers hardness of the ZTA composites that were sintered at $1600^{\circ}C$ for 2 hrs was found to smoothly decrease with increasing zirconia content because of the low Young modulus in zirconia. The Vickers hardness of the ZTA containing 3YEH zirconia was greater than that of the 3YEM zirconia. In substance, the fracture toughness ($K_{1c}$) of the ZTA composites increased as the content of zirconia increased. The fracture toughness ($K_{1c}$) of ZTA containing 3YEM zirconia was greater than that of 3YEH zirconia.

• Smart Media Journal
• /
• v.12 no.2
• /
• pp.15-26
• /
• 2023

Due to the global COVID-19 pandemic, which has led to a shift towards remote work, the frequency of external access to important internal resources by companies has increased exponentially, exposing them to various security threats. In order to address these access security issues, ZTA (Zero Trust Architecture) has gained attention. ZTA operates on the principle of not trusting external or internal users, and manages access authentication and authorization strictly according to pre-established policies. This paper analyzes the definition of ZTA and key research trends, and summarizes different ZTA solutions for each company.

• Journal of the Korean Ceramic Society
• /
• v.31 no.1
• /
• pp.17-24
• /
• 1994

Al2O3-ZrO2(ZTA) composites were fabricated by a surface-induced coating of the precursor for the ZrO2 phase on the kinetically stable colloid particles of Al2O3. The fabricated composites were characterized by a uniform spatial distribution of the dispersed ZrO2 phase and by the absence of large ZrO2 grains throughout the Al2O3 matrix. The fracture toughness (KIC) and the bending strength of ZTA composites sintered at 1$600^{\circ}C$, respectively, were 5.6 MPa.m1/2 (for 20 wt% ZrO2) and 600 MPa (for 15wt% ZrO2). The fraction of tetragonal ZrO2 phase decreases as the total content of ZrO2, suggesting that both the stress-induced tlongrightarrowm transformation and the microcrack nucleation contribute to the toughening of the ZTA composites fabricated by the surface-induced coating.

• Korean Journal of Materials Research
• /
• v.23 no.4
• /
• pp.250-254
• /
• 2013

In order to increase the toughness of ZTA(zirconia toughened alumina) ceramics, the present study focused on rearrangement and densification of particles according to the particle size of the parent material. When rough alumina was used for production of ZTA, densification behavior was observed in the specimen sintered at a temperature over $1550^{\circ}C$. However, it was found that the densification behavior was occurred in the specimen sintered at $1450^{\circ}C$ when fine alumina powder was used. High relative density exceeding 98% was obtained when fine alumina powder was mixed with 15 wt% of 3Y-TZP and sintered at $1600^{\circ}C$. Also, a hardness of 1820.2 Hv was obtained when a specimen containing 10 wt% of 3Y-TZP was sintered at $1600^{\circ}C$. In the case of 3Y-TZP containing rough alumina powder that had been sintered the hardness value was around 1720.3 Hv. It was predicted that an improved toughening effect in ZTA could be achieved by using finer alumina powder as the parent material.

• Korean Journal of Materials Research
• /
• v.16 no.12
• /
• pp.743-746
• /
• 2006

ZTA tubes were prepared by centrifugal casting and sintered at $1600^{\circ}C$ for 2 hrs. The ZTA tubes were machined into specimens of $3{\times}4{\times}40$ mm. Molten Soda lime glass (SLG) was penetrated into the surface of ZTA at an optimized condition of $1500^{\circ}C$ for the holding time of 5 h and furnace cooled. The extra glass on the surface was removed using a resin bonded diamond wheel. The glass penetrated samples were tested for their flexural strength using four point bend test. Vickers Indentation cracks were made on the glass penetrated surface at different loads of 9.8 N, 49 N, 98 N and 196 N. The residual compression on the surface enhanced the flexural strength and crack arrest behaviour remarkably. This was attributed to the thermoelastic mismatch between the glass and ZTA matrix during cooling.

• Journal of the Korean Ceramic Society
• /
• v.27 no.3
• /
• pp.369-382
• /
• 1990

ZrO2-Toughened Alumina-Ceramics(ZTA) with Cr2O3 and HfO2 as addition were synthesized by assintering method for solid solution of Al2O3/Cr2O3 and ZrO2/HfO2, and were prepared by pressureless sintering at 1$600^{\circ}C$. The effects of Cr2O3 and HfO2 on the thermal and mechanical properties, the sintering mechanism, and the wearness between theory and experiment were investigated. Among three kinds of mechanisms such as stress-induced transformation, microcracking, and crack deflection it contributed to the ZTA system with a few exceptons according to composite. We show that wearness can be estimated sufficiently by HV and KIC through theory and experiment.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.06a
• /
• pp.13-17
• /
• 1997

The densification of $Al_2$O$_3$/15v/o ZrO$_2$ (Zirconia Toughened Alumina: ZTA) to the 99% of theoretical density was attempted by controlling the processing parameters affecting the each processing step i.e., milling, spray-drying, forming and pressureless sintering. The ZTA processed under the identical conditions showed a large variation in the green and sintered densities, and the mechanical properties. The deviation of 4-point bending strength was more than 100MPa for the ZTA with ~99% of theoretical density. Moreover, the relative green and sintered densities were deviated greatly from the average value. This low reproducibility could be caused by the variation of spray-dried granule properties. Thus, the effect of yield strength and morphology of spray-dried ZTA granule on the green and sintered densities and the mechanical properties needs to be studied in detail. The objective of this work is to fine out the optimum condition of compaction pressure and compaction method depending on the properties of spray-dried granules.

• Journal of the Korean Ceramic Society
• /
• v.27 no.3
• /
• pp.329-336
• /
• 1990

In this investigation, bar-shaped specimens which consisted of three layers are prepared to study the effects of residual compressive stress on the mechanical properties in ZTA. The outer layers contained Al2O3 and unstabilized ZrO2 and the central layer contained Al2O3 and stabilized ZrO2(with 5.10wt% Y2O3). When cooled from the sintering temperature, some of zirconia in the outer layers transformed to the monoclinic form while zirconia in the central layer was retained in the tetragonal form. The transformation which induces to dilatational expansion led to the estabilishmenet of compressive stress in the outer layers and balances tensile stress in the central layer. Decrease of outer layer thickness(for a fixed total thickness)increases residual compressive stress. Because of residual compressive stress in the outer layers, the fracture toughness of outer layers of 3-layers composite is 10.21 Mpam1/2, which is increased to 25% above in comparison with 1-layer specimens in ZTA. Also, the 3-layers composite is believed to exhibite greater fracture resistance in contact damage environment from thermal shock test.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.2
• /
• pp.356-364
• /
• 1998

The dependence of green and sintered densities of Zirconia-Toughened Alumina ($ZTA:\;Al_2O_3/\;15\;vol{%}\;ZrO_2$) on the properties of spray-dried granules was studied thoroughly to establish the optimum compaction condition leading to high reproducibility in the light of sintered density. The sphericity, mean size, degree of hollow occurrence and moisture content of spray-dried granules were largely different in between the granule containing binder and the ones with no binder. The effect of these differences in the characteristic of granules on the compaction behavior was examined in terms of the compaction pressure from 80 MPa to 120 MPa 10 MPa increment and the compaction method, i.e., uniaxial and cold isostatic pressing. This work confirmed that the reproducibility of sintered density caused by the variation of granule property could be improved by the optimization of compaction process. The variation of sintered density was controlled within 1 % deviation by compacting the granules under a relatively low pressure of 80 MPa in an uniaxial forming and subsequent cold isostatic pressing at high pressure of 500 MPa.

• Journal of the Korean Ceramic Society
• /
• v.28 no.9
• /
• pp.696-704
• /
• 1991

ZrO2-Toughened Alumina-Ceramics (ZTA) with SiC Whisker as dispersive additive were prepared by pressureless sintering at 1$600^{\circ}C$ and 1$650^{\circ}C$ and by HIPing at 1$600^{\circ}C$ in Ar atmosphere. Effects of SiC-Whisker addition on microstuructural, mechanical, and thermal properties were investigated and the toughening mechanisms between theory and experiment were compared. Specimens with 15 vol% Whisker prepared by HIPing showed 8.26 MPa.ma1/2 in fracture toughness and 600 MPa in flexural strength owing to contribution of the three mechanisms such as crack deflection, whisker bridging and whisker pullout in spite of difference between the theoretical and experimental values due to the partial inhomogeneous dispersion of SiC-Whisker in the matrix and the processing flaw.