• 대한기계학회논문집B
• /
• 제23권7호
• /
• pp.820-830
• /
• 1999

The coupled turbulent flow and solidification is considered in a typical slab continuous easting process using commercial program FIDAP. Standard $k-{\varepsilon}$ turbulence model is modified to decay turbulent viscosity in the mushy zone and laminar viscosity is set to a sufficiently large value at the solid region. This coupled turbulent flow and solidification model also contains thermal contact resistance due to the mold powder and air gap between the strand and mold using an effective thermal conductivity. From the computed flow pattern, the trajectory of inclusion particles was calculated. The comparison between the predicted and experimental solidified shell thickness shows a good agreement.

• 설비공학논문집
• /
• 제11권6호
• /
• pp.766-773
• /
• 1999

A numerical analysis has been performed solidification problem using the fixed grid-enthalpy method with enthalpy-porosity relation. A modified standard $k-\varepsilon$ model was applied to describe the influence of turbulent flow. Computational procedures are based on the finite volume method and the non-staggered grid system. Comparisons with the different three experimental results show that applying a modified standard $k-\varepsilon$model in mushyzone is better than the previous computation results. This paper includes another EMBR's influences such as change of velocity field, Increasement of temperature and dispersion of flow out of nozzle into the flow field. These EMBR's influences are compared to case without EMBR.

• 대한기계학회논문집
• /
• 제12권6호
• /
• pp.1217-1226
• /
• 1988

본 연구에서는 고속연속주조의 기초적 연구로서 벌징만을 선택하여 주조속도 의 변화에 의한 주편의 거동을 해석하기 위해 응력을 변형률, 변형률속도, 온도의 함 수로서 잡고 크리프 변형과 탄소성 변형을 동시에 고려한 모델을 도입하여 주편내에서 의 벌징량, 변형률 등의 상태를 밝히며, 고속주조에 있어서 고려해야 할 사항에 대하 여 고찰한다.

• 한국재료학회지
• /
• 제21권11호
• /
• pp.581-586
• /
• 2011

This study describes a hydrogen embrittlement evaluation of the subsurface zone in 590DP steel by micro-Vickers hardness measurement. The 590DP steel was designed to use in high-strength thin steel sheets as automotive materials. The test specimens were fabricated to 5 series varying the chemical composition through the process of casting and rolling. Electrochemical hydrogen charging was conducted on each specimen with varying current densities and charging times. The relationship between the embrittlement and hydrogen charging conditions was established by investigating the metallography. The micro-Vickers hardness was measured to evaluate the hydrogen embrittlement of the subsurface zone in addition to the microscopic investigation. The micro-Vickers hardness increased with the charging time at the surface. However, the changing ratio and maximum variation of hardness with depth were nearly the same value for each test specimen under the current density of 150 mA/$cm^2$ and charging time of 50 hours. Consequently, it appears that hydrogen embrittlement in 590DP steel can be evaluated by micro-Vickers hardness measurement.

• 대한기계학회논문집
• /
• 제10권3호
• /
• pp.408-418
• /
• 1986

본 연구에서는 표면은 단단하고 내면은 강인한 조직을 얻기위하여 대형 성형 탄 로울에 대하여 노에서의 급속가열 및 대기 상태에서의 자연냉각의 열처리가 수행 되어진다. 급속가열 및 냉각시 성형탄 로울 내부의 온도 분포 예측을 위하여 대류 및 복사 열전달 경계조건을 가지는 1차원 비정상 열전도 방정식이 유한 차분법을 사 용하여 해석되어졌다. 여기서 급속가열시 연소가스로 부터 기체복사에 의하여 성 형탄 로울의 바깥표면을 통하여 흡수되는 열량은

• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.695-703
• /
• 1998

The crack problem of continuous casting slab due to the thermal stresses during the reheating process is analyzed using FEM. In this study, the C(t)-integral is calculated. As a result, the values of the C(t)-integral decrease by increasing the initial temperature of the slab and decreasing total heat flux. And those decrease by decreasing the heat flux of pre-heating zone and increasing the heat flux of heating zone.

• 한국주조공학회지
• /
• 제14권5호
• /
• pp.455-463
• /
• 1994

Aluminum matrix composites reinforced by fine steel wires were fabricated by squeeze casting process. Preforms made of fine steel wires were prepared with different surface conditions, namely uncoated(TN), carbo-nitriding treated(TT), and brass coated(TA). Squeeze casting were performed under the pressure of $1500kg/cm^2$ for 3min. during solidification, and pouring temp. of the melt being $750^{\circ}C$ and the steel mold being preheated at $250^{\circ}C$. Microstructural characteristics were evaluated, particularly concerned with the effect of the surface conditions of the preforms. The results obtained from this study are like these. TN specimens show partially non-wetted regions, due to easy formation of oxides on the surface of the fine steel wires. TT specimens show no interfacial reaction between the steel wires and the aluminum alloy matrix, possibly due to the formation of carbo-nitrided zone on the surface of the steel wires. TA specimens show excellent wettabillity between the reinforced steel wires and the aluminum alloy matrix and very thin interfacial zone is formed between them. During the solution hardening treatment of TA specimens, thickness of the interfacial reaction zones were increased with the solution treating time. TA specimens show typical ductile fracture in tensile test, but TT specimens show brittle fracture possibly due to the formation of the brittle hard surface on the steel wires during carbo-nitriding treatments. TA specimens which were reinforced with 40 vol.% of the fine steel wires exhibit high tensile strength of $77.1kgf/mm^2$ and impact value of $8.1kgf-m/cm^2$.

• 보존과학회지
• /
• 제32권1호
• /
• pp.11-19
• /
• 2016

승자총통은 중국 화기를 모방하여 선조(宣祖,1552-1608) 시기에 독자적인 화기 제작방식으로 만들어진 우리나라 유통식 소화기(小火器)이다. 이 연구는 경희대학교 중앙박물관 소장 승자총통을 중심으로 명문 판독 결과와 함께 과학분석 결과를 정리한 것이다. 경희대학교 중앙박물관에 소장하고 있는 승자총통 3점은 각 원소의 함량차이가 크지 않은 Cu-Sn-Pb 삼원계 합금으로 제작되었고 분석대상 중 미세조직 분석이 가능한 승자총통 1의 미세조직을 분석한 결과 일반적인 주조방식에 의해 제작되었으며 추가적인 열처리나 담금질 흔적은 관찰되지 않는다는 점이 밝혀졌다. 또한 승자총통 제작 시 사용한 납의 출처를 알아보고자 납동위원소비 분석을 실시한 결과 한국 남부 zone 2 지역(경상북도 북부와 강원도 남부지역)의 납광석을 사용하여 승자총통을 제작한 것으로 판단된다.

• 대한치과기공학회지
• /
• 제23권2호
• /
• pp.203-210
• /
• 2002

This test is to conduct applied research the reaction area of the Ti-cast metal body which is made use of Dental Phosphate-silica alumina bonded investment material selling at a market, and the cooling method is how to effect on the acicular. The experimentation is as followings, 1. Experimental specimens After invest with Dental Phosphate-silica alumina bonded investment material, the $10{\times}10{\times}1.0mm^3$ wax pattern was casted by Dental high vacuum argon centrifugal casting machine. 2. Test We can analyze SEM/EDS, XRD utilize the fractography(an optical microscope). 3. Conclusion The pure cast metal body constituted of reaction products layer, stability layer and contamination layer. This pure cast have no connection with the cooling condition. The pure Titanium shows difference in a component distribution according to the cooling condition. Through this experimentation we can establish that acicular in the pure Ti-cast metal is consist of Hexagonal structure a=2.9505$\AA$, c=4.6826$\AA$.

• Journal of Pharmaceutical Investigation
• /
• 제30권2호
• /
• pp.93-98
• /
• 2000

In order to evaluate the effect of fabrication methods on the controlled release of an antibiotic from a polymeric device, two types of polyurethane-cefadroxil matrix were prepared by the solvent casting method or the freeze drying method, using bovine serum albumin as a pore former. The amount of cefadroxil released from various formulations at $37^{\circ}C$ was measured by HPLC. The duration of antimicrobial activity of matrices against S. aureus was evaluated by measuring the diameters of the inhibition zone. The morphology of the matrices was investigated by scanning electron microscopy (SEM). Changing the fabrication method could alter the release rate of cefadroxil from the matrix. The matrix fabricated by the freeze drying method had more porous inner structure and showed higher release rate than that prepared by the solvent casting method. However, the duration of antimicrobial activity was shorter when the matrix was fabricated by the freeze drying method.