• Economic and Environmental Geology
• /
• v.27 no.3
• /
• pp.247-261
• /
• 1994

Honam Shear Zone is a mylonite zone approximately parallel to the NE-SW trend located southern part of Korea peninsula. Geologic ages and petrogenesis of foliated granites in this zone are as follows: Igneous rocks of this zone are composed of granite gneiss, Paleozoic granites, Songrim granites, Jurassic granites and Cretaceous granites. Foliated granites show deformed phase of Paleozoic and Songrim granites during Daebo Orogeny. And isotopic ages obtained from foliated granites are early Permian to late Triassic period (276~200 Ma). Most of foliated granite masses are igneous complex consisting of a series of differential product of cogenetic magma. The individual rock mass of foliated granites plotted on Harker diagram shows mostly similar trend of calc-alkali series. REE diagram indicates that LREE amount of foliated granites are more enriched than HREE and negative Eu anomalies of them are weaker than those of the other granites. From these data, we suggest the rocks are generated from continental margin under syntectonic environment. Original magma type of foliated granites correspond to I-type, syn-collision type and Hercyano type. In compressive stress field between Ogcheon folded belt and Youngnam massif, foliated granites had formed due to mylonitic deformation. Those facts indicate that magma of foliated granites would had been generated by melting in lower crust or contamination in upper mantle.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.290-294
• /
• 1997

In this study, the welded residual stresses test was carried out with pure titanium and TIG welded material using in chemical plants an airplane frames etc.. The relationship between process parameters and residual stresses is complex since a number of factors are involved. Extensive studies have been carried out to determine the effects of various process parameters on residual stress. The result of micro-hardness about butt welded spacemen was measured of low hardness value in the melting metal zone. The residual stress of welded zone on the Titanium plate by the sectioning method and finite element method was high measured in the spacemen of high current and voltage. Also, compressive residual stress in the range of distance about 15∼20mm from the middle of the deposited metal area is very change. The result of impact test about butt welded spacemen of pure titanium plate was measured of very difference in the welded bead, heat affect zone and base metal, and be measured of high impact value in the heat affect zone. The measure result of welded residual stresses about pure titanium is high measured hen nominal steel plate. The V-Type butt welded spacemen, that of the measurement result on the welded residual stress is high measure then X-Type butt welded spacemen.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.1-7
• /
• 2014

For the resistance spot welds of CR1180 and GA1180 TRIP steels, the weld quality evaluation method using the digitalized X-ray transmission imaging apparatus was investigated in comparison with the crosssectional examination method. In the case of the resistance spot welding of CR1180, three circular regions, such as WZ(white zone), GZ(grey zone) and DZ(dark zone), appeared on X-ray image and they corresponded to the diameters of indentation mark, nugget and corona bond, respectively. The variation of X-ray transmission thickness due to the thickness variation of the weld seemed to be mainly responsible for the formation of those contrasts. The X-ray image contrast formed from the variation of transmission thickness at the outer border line of DZ could also enable the inspections of the notch shape, nonuniformity of the welding pressure and spatter from its sharpness, concentricity and the normal straight line, respectively. The X-ray image of the resistance spot weld of galvannealed GA1180 TRIP steel was very similar to that of CR1180 TRIP steel except the crown shaped outer border line of DZ which was considered to be due to the melting behavior of zinc having the boiling temperature even lower than the melting temperature of steel.

• Economic and Environmental Geology
• /
• v.33 no.4
• /
• pp.249-260
• /
• 2000

The development of dual volcanic chains, parallel to the trend of the subduction trench, is observed in the southern part of Korea. Elsewhere on the Earth volcanic arcs dominantly consist of two such chains. In the southern part of Korea, two volcanic chains within a single volcanic arc was developed. Kyongsang basin, where the first volcanic chain located, and Youngdong-Kwangju depression zone where the second volcanic zone located, showed sub-parallel volcanic rock distributed areas. Concentrations of incompatible elements in the southern part of Korea samples show clear across-arc variations, with lavas from the first volcanic chain being most depleted in these elements, all incompatible element concentrations increase towards the second volcanic chain. The above across-arc variation may be caused by the difference in solid phases coexisting with the fluid phases during the dehydration processes. The concentrations of incompatible elements, Zr/Y ratios, and Rb/K ratios indicate that the second volcanic chain (Youngdong-Kwangiu depression zone) was generated by low degrees of partial melting at the deeper depth compared to the conditions of the first volcanic chain (Kyongsang basin) and residual garnet probably attributed to the their partial melting.

• Journal of Welding and Joining
• /
• v.26 no.2
• /
• pp.92-97
• /
• 2008

In welding of thin plate, some defects such as melt through and unmelted zone occur easily at welding start, however there is a limited study on those problems. Therefore the effects of start block and arc length on melt through and unmelted zone at start were investigated in this study. When start block height was lower than base metal, there was melt through at start. And when the height was even with base metal, no unmelted zone existed. Unmelted zone was increased as start block height increased from 0mm to 0.5mm. However unmelted zone was not much changed as the height increasing from 0.5mm to 1.0mm. When gap existed between start block and base metal, melt through occurred. However, unmelted zone was increased as the contact force of start block on base metal was increased from 0kgf to 7.5kgf. And when arc length was decreased from 3.8mm to 3.0mm, unmelted zone was decreased. It was concluded that the optimum condition to prevent melt through and to minimize unmelted zone would be with start block height 0.25mm, contact force 3.0kgf, and arc length 3.4mm. This optimum condition was applied to the mass production line and resulted in satisfied outcome.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.11a
• /
• pp.67-67
• /
• 2001

The structure zone model has been used to provide an overview of the relationship between the microstructure of the films deposited by PVD and the most prominent deposition condition.s. B.AMovchan and AV.Demchishin have proposed it firstls such model. They concluded that the general features of the resulting structures could be correlated into three zones depending on $T/T_m$. Here T m is the melting point of the coating material and T is the substrate temperature in kelvines. Zone 1 ($T/Tm_) is dominated by tapered macrograins with domed tops, zone 2 ($O.3) by columnar grains with denser boundaries and zone 3 ($T/T_m>O.5$) by equiaxed grains formed by recrystallization. J.AThomton has extended this model to include the effect of the sputtering gas pressure and found a fourth zone termed zone T(transition zone) consisting of a dense array of poorly defined fibrous grains. R.Messier found that the zone I-T boundary (fourth zone of Thorton) varies in a fashion similar to the film bias potential as a function of gas pressure. However, there has not nearly enough model for explaining the change in morphology with crystal orientation of the films. The structure zone model only provide an information about the morphology of the deposited film. In general, the nucleation and growth mechanism for granular and fine structure of the deposited films are very complex in an PVD technique because the morphology and orientation depend not only on the substrate temperature but also on the energy of deposition of the atoms or ions, the kinetic mechanism between metal atoms and argon or nitrogen gas, and even on the presence of impurities. In order to clarify these relationship, AI and Mg thin films were prepared on SPCC steel substrates by PVD techniques. The influence of gas pressures and bias voltages on their crystal orientation and morphology of the prepared films were investigated by SEM and XRD, respectively. And the effect of crystal orientation and morphology of the prepared films on corrosion resistance was estimated by measuring polarization curves in 3% NaCI solution.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.2
• /
• pp.66-71
• /
• 2000

Laser induced surface hardening of Tool steel(STC5) can be achieved either with or without surface melting. In trans-formation hardening as the surface is heated to a temperature below its melting point and is rapidly cooled solidified microstructures are usually much finer and stronger than those of the base matals. For this reason surface modification of tool steel by YAG laser irradiation has been studied as a function of processing parameters such as power density pulse width defocusing distance and molten depth. The high energy density changes and refines the microstructure of the near surface layer. In the case of beam passes martensite formed in the melt zone exhibited very high vickers hardness values. Molten depth and width depend on defocusing distance and energy of black color painting is more absorptive than other color painting.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.12
• /
• pp.1023-1029
• /
• 2015

Laser-assisted machining (LAM) is one of the most effective methods for enhancing the machinability of difficult-to-cut materials, such as titanium alloys and various ceramics, and has been studied by many researchers. LAM is a method that facilitates machining by softening a workpiece using a laser heat source. The advantages of the LAM process are decreases in tool wear, cutting force, and surface roughness. However, when the material is over-heated, melting or burning can occur. This study analyzed the heat source distribution with regard to overlapping of preheating on the laser heating path with an acute angle, a right angle and obtuse angles. Then, a power reduction method was proposed to reduce the melting and burning of the workpiece.

• Journal of Welding and Joining
• /
• v.19 no.4
• /
• pp.379-383
• /
• 2001

Resistance spot welding has been widely used in the sheet metal joining processes because of low cost, high productivity and convenience. Recently, automobile and aerospace industries are trying to replace partly steel sheets with aluminum alloy sheets. But in the case of dissimilar materials, to apply resistance spot welding has been known to be very difficult owing to the effect of melting temperature. On this study, an effort was made to apply spot welding of dissimilar sheet metals, 2024 aluminum alloy and zinc coated steel sheet, evaluate the spot weld quality with tensile-shear strength test and nondestructive evaluation technique, C-scan image methodology. In this study results, as the current below 11 kA, melting of materials is not achieved well. Also as the current exceeds to 13.5 kA, the more spatters happen at welded zone and tensile-shear strength lowered. So, the feasibility of C-scan image technique proposed in the study is found to be suitable evaluation method for resistance spot weldability.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10b
• /
• pp.76-79
• /
• 2003

Recently, many attempts have been made to develop high strength and high modulus fibers from conventional polymers such as poly(vinyl alcohol) (PVA)[1-4] and polyethylene (PE). PVA has potentiality to yield high strength and high modulus fiber, since they have high theoretically attainable moduli because of their planar zig-zag structure. As PVA has a melting temperature as high as 230$^{\circ}C$ in contrast to PE with a low melting temperature such as 130$^{\circ}C$, it seems possible that high strength and high modulus fibers comparable to Aramid can be fabricated from PVA. (omitted)