• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.3
• /
• pp.511-518
• /
• 2021

In order to obtain a good tracking performance of the motor, it is necessary to design a controller that can respond to a disturbance by including a disturbance observer. The disturbance observer of the motor is designed to estimate the load torque and the back electromotive voltage based on the first-order low-pass filter. A PI controller and an IP controller were designed to compare the correlation between the disturbance observer and the controller and to obtain improved control performance. To check the performance of the designed observer and the controller, it was applied to a 120 [W] class BLDC motor. As a result, overshoot is reduced, and it can be seen that the steady-state error converges to zero.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.481-488
• /
• 2000

This paper presents a new passive gravity -compensating system for articulated robot manipulators. The system, which consists of linear zero- free -length springs, achieves exact counterbalancing o f the gravitational loads throughout the entire range of the manipulator workspace, A basic concept is to design springs such that the total potential energy of the system including the manipulator and the springs should be maintained constant. A prototype has been developed for a direct-drive five-bar manipulator and its performances have been investigated. Results show that the gravity-induced motor torques have been reduced to less than 5% of those of uncompensated robots. Also, the gravity-compensating system simplifies the position control algorithm while maintaining the trajectory-tracking errors in a satisfactory level. In conclusion, the proposed system efficiently improves the manipulator performances by reducing the driving motor size and the energy consumption as well as by simplifying the control systems.

• Journal of Power Electronics
• /
• v.7 no.3
• /
• pp.222-232
• /
• 2007

This paper presents the application of a single phase AC-to-DC converter using a three-phase series parallel (SPRC) resonant converter to variable speed dc-drive. The improved power quality converter gives the input power factor unity over a wide speed range, reduces the total harmonic distortion (THD) of ac input supply current, and makes very low ripples in the armature current and voltage waveform. This soft-switching converter not only possesses the advantages of achieving high switching frequencies with practically zero switching losses but also provides full ranges of voltage conversion and load variation. The proposed drive system is the most appropriate solution to preserve the present separately excited de motors in industry compared with the use of variable frequency ac drive technology. The simulation and experimental results are presented for variable load torque conditions. The variable frequency control scheme is implemented using a DSP- TMS320LF2402. This control reduces the switching losses and current ripples, eliminates the EMI and improves the efficiency of the drive system. Experimental results confirm the consistency of the proposed approach.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.5
• /
• pp.585-591
• /
• 1998

It is proposed a new compensation method in the rotor time constant of indirect vector controlled induction motor. The proposed scheme is an on-line method using the stator current error that is the difference between current command and estimated current calculated from terminal voltages and currents. As the current error becomes to zero, the rotor time constant in the vector controller approaches the real value. The proposed method shows good performances in the transient region as well as in the steady state region regardless of load torque variation, and it is verified by the computer simulation using SIMULINK in Matlab.

• Journal of the Semiconductor & Display Technology
• /
• v.6 no.1 s.18
• /
• pp.31-36
• /
• 2007

Effect of coulomb friction and backlash on the single loop position control has been studied for the precision position control. We have showed the limit cycle on the single loop system which used a ball screw that had the backlash. Also, we have made an inner loop with a classical velocity and torque controller which was forcing the current of d axis to be zero by using a permanent-magnet synchronous motor and composed the outer loop with linear encoder for sensing a position of the loader. Also, we have used least squares fit(LSF) observer for reducing noise when we got velocity from position outputs. We have shown a good result by using the dual loop through simulation and experiment.

• Journal of Power Electronics
• /
• v.11 no.2
• /
• pp.120-131
• /
• 2011

This paper proposes two control strategies for the bidirectional Z-source inverters (BZSI) supplied by batteries for electric vehicle applications. The first control strategy utilizes the indirect field-oriented control (IFOC) method to control the induction motor speed. The proposed speed control strategy is able to control the motor speed from zero to the rated speed with the rated load torque in both motoring and regenerative braking modes. The IFOC is based on PWM voltage modulation with voltage decoupling compensation to insert the shoot-through state into the switching signals using the simple boost shoot-through control method. The parameters of the four PI controllers in the IFOC technique are designed based on the required dynamic specifications. The second control strategy uses a proportional plus resonance (PR) controller in the synchronous reference frame to control the AC current for connecting the BZSI to the grid during the battery charging/discharging mode. In both control strategies, a dual loop controller is proposed to control the capacitor voltage of the BZSI. This controller is designed based on a small signal model of the BZSI using a bode diagram. MATLAB simulations and experimental results verify the validity of the proposed control strategies during motoring, regenerative braking and grid connection operations.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.6
• /
• pp.565-575
• /
• 2009

A forklift (also called a lift truck) is a powered industrial truck that is used to lift and transport materials. It has become an indispensable piece of equipment in manufacturing and warehousing operations. The modem forklift is equipped with automatic transmission to meet the requirement of loading and easy operation of the vehicle. This paper proposes the design of TECU(Transmission Electronic Control Unit) which is applied to PSD322-Axle transmission. Garofalo's control technique is generally used to the automatic transmission. We consider the work quality and market requirement that does not want to control engine throttle. This paper proposes new controller system which guarantees efficient speed changes with simple system. This new system does not control the engine throttle spontaneously. But it has the load of engine and vehicle as a maximum disturbance. The scope of the disturbance is limited to the stoll area of the torque converter. This paper proposes a ideal control commander that converges relative velocity of the input and ouput of a clutch into a zero. We design linear controller to execute the idea control commander. We applied the control algorithm to the forklift of PSD322-Axle type and the performance of this controller was verified.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.10
• /
• pp.1065-1072
• /
• 2008

A HDD adopts a sensorless brushless DC (BLDC) motor as a spindle motor. Because there is no direct sensor measuring rotor position. open loop commutations with inductive sensing are used to increase the rotor speed up to a certain speed where the zero crossings of the back electromotive force (EMF) voltage are measurable. Therefore, successful open loop commutations are necessary for the stable start-up control of the spindle motors. In this paper, the time scale and the number of the open loop commutations are employed for design parameters to guarantee robustness to torque constant variation and initial rotor position. The design results are verified by experiments on a very low current start-up of the spindle motor with various environment. The experimental results show that the design results can decrease the start-up failure rate considerably.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.10a
• /
• pp.178-183
• /
• 2006

Effect of coulomb friction and backlash on the single loop posit ion control has been studied for the precision position control. We studied and showed the limit cycle on the single loop system which used a ball screw that had the backlash. Also, We made an inner loop with a classical velocity and torque controller which was forcing the $i_d$ current to be zero by using a permanent-magnet synchronous motor and composed the outer loop with linear sensor for sensing a position of the loader. We have been shown a good result by using the dual loop through numerical simulation method.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.11
• /
• pp.888-895
• /
• 1989

A novel model reference adaptive control (MRAC) scheme for electrical servo drives is proposed, in which the control input is synthesized without any parameter identification mechanism and a PI controller is inserted ahead of the plant to reduce the steady state chattering. The proposed scheme is shown to be asymptotically stable in the case where the load torque disturbance satisfies a certan condition. An application to a permanent magnet synchronous motor drive shows that the output error between the plant and the reference model tends to zero and the chattering is greatly reduced.